ENGLISH OWNER’S MANUAL DRYER Read this owner’s manual thoroughly before operating the appliance and keep it handy for reference at all times. DLE7300*E (Elec) DLG7301*E (Gas) www.lg.com MFL70442606 Rev.01_112218 Copyright © 2018 LG Electronics Inc. All Rights Reserved.
TABLE OF CONTENTS TABLE OF CONTENTS 3 PRODUCT FEATURES 41 SMART FUNCTIONS 41 Smart ThinQ Application 4 SAFETY INSTRUCTIONS 43 Smart Diagnosis™ Function 5 7 44 mAINTENANCE IMPORTANT SAFETY INSTRUCTIONS GROUNDING INSTRUCTIONS 44 Regular Cleaning 8 PRODUCT OVERVIEW 8 Parts 8 Accessories 8 Safety Tether Kit 8 Two-Way Reversible Door (on some models) 9 INSTALLATION 9 Installation Overview 9 Product Specifications 10 Installation Location Requirements 10 Clearances 12 Leveling the Dryer
PRODUCT FEATURES ENGLISH PRODUCT FEATURES Easy-to-Use Control Panel An entire selection of user-friendly functions make operating the dryer easy. Two-Way Easy-Access Reversible Door D The LG EasyLoadTM can be tilted open from the top, hamper-style, allowing you to easily load the dryer without items falling on the floor. The door still swings open to provide easy access for unloading or loading of bulkier items. The door hinge can be reversed to adjust to the installation location.
SAFETY INSTRUCTIONS SAFETY INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE USE Your safety and the safety of others is very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word DANGER, WARNING, or CAUTION.
SAFETY INSTRUCTIONS 5 Warning To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic precautions, including the following: Installation •• Keep area around the exhaust opening and adjacent surrounding areas free from the accumulation of lint, dust, and dirt. •• Do not install or store this appliance where it will be exposed to the weather. •• Do not place items exposed to cooking oils in your dryer.
SAFETY INSTRUCTIONS Operation Steam (steam model): •• Read all instructions before using the appliance. •• Do not open the dryer door during steam cycles. Failure to follow these instructions may result in a burn hazard. •• Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, or other flammable or explosive substances, as they give off vapors that could ignite or explode.
SAFETY INSTRUCTIONS 7 ENGLISH GROUNDING INSTRUCTIONS Warning Improper connection of the equipment-grounding conductor may result in a risk of electric shock. Check with a qualified electrician or service person if you are in doubt that the appliance is properly grounded. •• This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current.
PRODUCT OVERVIEW PRODUCT OVERVIEW Parts Control panel Reversible door Lint filter Leveling feet Accessories Terminal block access panel (electric models) Gas connection location (gas models) Power cord location (gas models) Water inlet valve (on some models) Exhaust duct outlet Two-Way Reversible Door (on some models) Included Accessories Release Safety Tether Kit (on some models) Hamper door Optional Accessories Swing door Drying rack (sold separately) No.
INSTALLATION ENGLISH INSTALLATION Installation Overview Please read the following installation instructions first after purchasing this product or transporting it to another location. Check and choose the proper location Level the dryer Connect electric dryers Connect gas dryers Installation test Vent the dryer Gas dryer Electric dryer Plug in the power cord Test run Product Specifications The appearance and specifications listed in this manual may vary due to constant product improvements.
INSTALLATION Installation Location Requirements Warning Read all installation instructions completely before installing and operating the dryer! It is important that you review this entire manual before installing and using the dryer. Detailed instructions concerning electrical connections, gas connections, and exhaust requirements are provided on the following pages. The installation requires: •• A location that allows for proper exhaust installation. A gas dryer must be exhausted to the outdoors.
INSTALLATION 11 Closets with doors must have both an upper and lower vent to prevent heat and moisture buildup in the closet. One upper vent opening with a minimum opening of 48 sq. in. (310 cm2) must be installed no lower than 6 feet above the floor. One lower vent opening with a minimum opening of 24 sq. in. (155 cm2) must be installed no more than one foot above the floor. Install vent grills in the door or cut down the door at the top and bottom to form openings.
INSTALLATION Leveling the Dryer 2 Warning To reduce the risk of injury to persons, adhere to all industry recommended safety procedures including the use of long-sleeved gloves and safety glasses. Failure to follow this warning may result in serious injury or death. Use an adjustable wrench to turn the leveling feet. Unscrew the legs to raise the dryer or screw in the legs to lower it. Raise or lower with the leveling feet until the dryer is level from side to side and front to back.
INSTALLATION 13 1 Open the door from the side so that the hinge screws are accessible. 4 Warning Be sure to support the weight of the door before removing the hinge screws. 2 Remove the four hinge screws. While supporting the door, remove the four hinge screws, two from each hinge. Set the door aside face down on a protected surface to prevent damage to the door or the work surface.
INSTALLATION 7 Reinstall the door. While supporting the door, install the four hinge screws removed in step 2. Test the swing of the door to make sure the hinges and latch are properly aligned and that the door opens, closes and latches properly. 2 Remove the door from cabinet. a. While supporting the door, remove the four hinge screws. Two large screws Two small screws b. Lift the door slightly to disengage the hinge support and remove the door from the cabinet.
INSTALLATION 15 ENGLISH Twelve screws CAUTION Do NOT remove any of the eight screws on the face of the cabinet (marked below). Doing so could result in damage to the dryer and the need for a service call to repair the dryer. Hole plug e. Remove the three screws on the hinge at the bottom left. Remove the hinge and reinstall it on the right side. The top screw will occupy the hole where you removed the screw behind the hinge bracket in step d.
INSTALLATION 6 Reverse the components inside the door. You will now be removing and reversing various components inside the door. See below for a detailed diagram and identification of the inner structure and parts of the door. (The diagram shows the “before view” of the door, with the default set-up for a right side hinge swing. After following these instructions, the door should be a mirror image of the illustration.
INSTALLATION 17 Lift out the gray interlock button in the side of the door. Make sure to remove the spring with the interlock button and to keep the two together. Set the interlock button aside. Do not confuse this with the interlock buttons from the top of the outer door. 8 Remove the side lock rod. Remove the side lock rod from the lower hinge bracket by lifting the top end of the rod and sliding it toward the top of the door. The spring should remain attached to the lock rod. Set the lock rod aside.
INSTALLATION 10 Reverse the lower hinge bracket and hinge assembly. a. Remove one screw from the lower hinge bracket (on the right) and lift it out. Remove two screws from the lower hinge assembly (on the left) and lift it out. 11 Install the side lock rod. a. Flip the side lock rod over and insert the lower end into the left hinge bracket. b. Lower the rod into the guides on the door while compressing the spring inside the recess.
INSTALLATION 19 Reinstall the side interlock button. Install the side interlock button on the opposite side from which it was removed. ENGLISH 12 NOTE Make sure the spring is on the interlock button and is centered in the compartment. 13 Reinstall the door cover. a. Clean the glass on the door and door cover, if necessary. b. Make sure the three gray interlock buttons are properly installed and that the top and side lock rods intersect properly. c.
INSTALLATION Installing the Side Vent Kit 3 Warning •• Use a heavy metal vent. •• Do not use plastic or thin foil ducts. •• Clean old ducts before installing this dryer. •• To reduce the risk of injury to persons, adhere to all industry recommended safety procedures including the use of long-sleeved gloves and safety glasses. •• Failure to follow all of the safety warnings in this manual could result in property damage, injury to persons, or death. Preassemble a 4-inch (10.
INSTALLATION 21 Warning To reduce the risk of fire or explosion, electric shock, property damage, injury to persons or death when using this appliance, follow basic safety precautions, including the following: •• Do not crush or collapse ductwork. Failure to follow these instructions may result in fire or death. •• Do not allow ductwork to rest on or contact sharp objects. Failure to follow these instructions may result in fire or death.
INSTALLATION Routing And Connecting Ductwork NOTE Follow the guidelines below to maximize drying performance and reduce lint buildup and condensation in the ductwork. Ductwork and fittings are NOT included and must be purchased separately. •• Use 4-inch (10.2 cm) diameter rigid, semi-rigid or flexible metal ductwork. •• The exhaust duct run should be as short as possible. •• Use as few elbow joints as possible. •• The male end of each section of exhaust duct must point away from the dryer.
INSTALLATION 23 Warning To reduce the risk of fire or explosion, electric shock, property damage, injury to persons, or death when using this appliance, follow basic safety precautions. Gas Supply Requirements •• As shipped from the factory, this dryer is configured for use with natural gas (NG). It can be converted for use with propane (LP) gas. Gas pressure must not exceed 8 inches (20.3 cm) of water column for NG, or 13 inches (33 cm) of water column for LP.
INSTALLATION Connecting the Gas Supply •• Installation and service must be performed by a qualified installer, service agency, or the gas supplier. Failure to do so may result in fire, explosion, or death. •• Use only a new stainless steel flexible connector and a new AGA-certified connector. Failure to do so may result in fire, explosion, or death. •• A gas shutoff valve must be installed within 6 ft. (1.8 m) of the dryer. Failure to do so may result in fire, explosion, or death.
INSTALLATION 25 Electrical Requirements for Electric Models Only Warning To help prevent fire, electric shock, serious injury, or death, the wiring and grounding must conform to the latest edition of the National Electrical Code, ANSI/NFPA 70 and all applicable local regulations. Please contact a qualified electrician to check your home’s wiring and fuses to ensure that your home has adequate electrical power to operate the dryer.
INSTALLATION Warning Connect the power cord to the terminal block. Connect each wire in the power cord to the terminal block screw with the matching colored wire. The terminal block wire colors are indicated in the manual. Failure to follow these instructions may result in a short or overload.
INSTALLATION 27 •• A 4-wire connection is required for all mobile and manufactured home installations, as well as all new construction after January 1, 1996. •• A UL-listed strain relief is required. •• Use UL-listed 4-wire #10 AWG-minimum copper conductor cable. Allow at least 5 ft. (1.5 m) of wire to allow for removal and reinstallation of the dryer. 1 Remove 5 inches (12.7 cm) of the outer covering from the wire. Remove 5 inches (12.7 cm) of insulation from the ground wire.
INSTALLATION 5 Warning Connect the power cord to the terminal block. Connect each wire in the power cord to the terminal block screw with the matching colored wire. The terminal block wire colors are indicated in the manual. Failure to follow these instructions may result in a short or overload.
INSTALLATION 29 9 Reinstall the terminal block access cover. Hot (Black) •• A 3-wire connection is NOT permitted on new construction after January 1, 1996. •• A UL-listed strain relief is required. •• Use UL-listed 3-wire, #10 AWG-minimum copper conductor cable. Allow at least 5 ft. (1.5 m) length to allow for removal and installation of dryer. 1 Remove 3½-inch (8.9 cm) of the outer covering from the wire. Strip 1 inch (2.5 cm) insulation from each wire.
INSTALLATION Installation Test (Duct Check) 4 Once you have completed the installation of the dryer, use this test to make sure the condition of the exhaust system is adequate for proper operation of the dryer. This test should be performed to alert you to any serious problems in the exhaust system of your home. •• This dryer features Flow Sense™, an innovative sensing system that automatically detects blockages and restrictions in dryer ductwork.
INSTALLATION 31 Restricted or Blocked Airflow Avoid long runs or runs with multiple elbows or bends. NOTE When the dryer is first installed, this test should be performed to alert you to any existing problems with the exhaust duct in your home. However, since the test performed during normal operation provides more accurate information on the condition of the exhaust duct than does the installation test, the number of bars displayed during the two tests may not be the same.
OPERATION OPERATION WARNINg To reduce the risk of fire, electric shock, or injury to persons, read this entire manual, including the IMPORTANT SAFETY INSTRUCTIONS, before operating this dryer. Using the Dryer Lint Filter 1 Clean the Lint Filter If the lint filter has not already been cleaned, lift out the filter and remove the lint from the last load. This will help ensure the fastest and most efficient drying performance.
OPERATION 33 Group Similar Items Always make sure the lint filter is clean before starting a new load; a clogged lint filter will increase drying time. To clean, pull the lint filter straight up and roll any lint off the filter with your fingers. Do not rinse or wash the filter to remove lint. Push the lint filter firmly back into place. See Regular Cleaning for more information. Different fabrics have different care requirements, and some fabrics will dry more quickly than others.
OPERATION Using the LG EasyLoadTM Swing Door Use the swing door when unloading, or when loading bulkier items, for easy access to the drum. To open the swing door, grasp the top of the door on the side opposite the hinge and pull. NOTE Make sure the hamper door release is completely closed before using the swing door. Hamper Door (on some models) Use the hamper door when loading.
OPERATION 35 1 2 3 4 5 7 1 POWER Button Press to turn the dryer ON. Press again to turn the dryer OFF. NOTE Pressing the POWER button during a cycle will cancel that cycle and any load settings will be lost. 2 Cycle Selector Knob Turn this knob to select the desired cycle. Once the desired cycle has been selected, the standard presets are shown in the display. On Manual Dry cycles, these settings can be adjusted using the cycle modifier buttons any time before starting the cycle.
OPERATION 8 9 10 11 13 12 8 Custom PGM If you have a special combination of settings that you use frequently, you can save these settings as a Custom Program. 12 Estimated Time Remaining This display shows the estimated time remaining for SENSOR DRY cycles or the actual time remaining for Time Dry or MANUAL DRY cycles.
OPERATION 37 Cycle = default setting = allowable option Fabric Type Dry Level Normal Dry Bedding Comforters, pillows, shirts Heavy Duty Jeans, heavyweight items Normal Work clothes, corduroys, etc. Perm.
OPERATION Manual dry cycles Sensor dry cycles utilize LG’s unique dual sensor system to detect and compare the moisture level in clothes and in the air and adjust the drying time as needed to ensure superior results. The dryer automatically sets the dryness level and temperature at the recommended setting for each cycle. The estimated time remaining will be shown in the display. NOTE Use dry cycles to select a specific amount I manual GN ES of drying time and a drying temperature.
OPERATION 39 Cycle Modifier Buttons SENSOR DRY cycles have preset settings that are selected automatically. MANUAL DRY cycles have default settings, but you may also customize the settings using the cycle modifier buttons. Press the button for that option to view and select other settings. Cycle Option Buttons The dryer features several additional cycle options to customize cycles to meet individual needs.
OPERATION Special Functions Some cycle option buttons also activate secondary functions. These special functions are marked with an asterisk (*). Press and hold the option button marked with the special function to activate it. Custom PGM If you have a special combination of settings that you use frequently, you can save these settings as a custom program. Saving a Custom Program: Drum Light The drum is equipped with a blue LED that illuminates when the dryer is turned on.
SMART FUNCTIONS 41 Smart ThinQ Application The Smart ThinQ application allows you to communicate with the appliance using a smartphone. Installing Smart ThinQ Application Search for the LG Smart ThinQ application from the Google Play Store or Apple App Store on a smart phone. Follow instructions to download and install the application. Smart ThinQ Application Features •• For appliances with the or logo.
SMART FUNCTIONS Wireless LAN Module Specifications Model LCW-004 Frequency Range 2412 MHz to 2462 MHz Output Power (Max) IEEE 802.11b: 22.44 dBm IEEE 802.11g: 24.68 dBm IEEE 802.11n: 24.11 dBm FCC Notice (For transmitter module contained in this product) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
SMART FUNCTIONS 43 Smart ThinQ Smart Diagnosis™ Should you experience any problems with the appliance, it has the capability of transmitting data via your telephone to the LG Customer Information Center. NFC or Wi-Fi equipped models can also transmit data to a smartphone using the LG Smart ThinQ application. •• For appliances with the Smart Diagnosis™ through the Customer Information Center Follow the instructions in the Smart ThinQ application to perform a Smart Diagnosis using your smartphone.
MAINTENANCE mAINTENANCE Regular Cleaning Warning To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions, including the following: •• Unplug the dryer before cleaning to avoid the risk of electric shock. Failure to follow this warning may cause serious injury, fire, electric shock, or death. Maintaining Ductwork Vent ductwork should be checked for lint buildup once per month and cleaned at least once per year.
Troubleshooting 45 ENGLISH Troubleshooting FAQs: Frequently Asked Questions Q: When I press a button, why does my dryer beep and then nothing happens? A: The Control Lock feature is turned on. To turn off Control Lock, turn the dryer on, then press and hold the button that has *Control Lock on or under it for 3 seconds. Q: Why does my dryer take so long to dry clothes? A: Proper airflow is critical to the efficient operation of clothes dryers.
Troubleshooting Before Calling for Service This dryer is equipped with an automatic error-monitoring system to detect and diagnose problems at an early stage. If the dryer does not function properly or does not function at all, check the following before you call for service. Operation Problem TM Possible Cause Solutions The Flow Sense indicator remains active after clearing the restriction in the venting.
Troubleshooting 47 Possible Cause Solutions Clothes take too long to dry Exhaust ducts are blocked, dirty, or duct run is too long. Confirm that the exhaust duct is properly configured and free of debris, lint, and obstructions. Make sure that outside wall dampers can open properly and are not blocked, jammed, or damaged. Load is not properly sorted. Separate heavy items from lightweight items. Larger and heavier items take longer to dry.
Troubleshooting Problem Possible Cause Solutions Clothes take too long to dry Energy Saver option selected (on some models) If using the Cotton/Normal cycle, deselect the Energy Saver option. This option reduces energy use by adding an air dry section to the beginning of the cycle. Drying time is not consistent Heat settings, load size, or dampness of clothing is not consistent.
Troubleshooting 49 Problem Greasy or dirty spots on clothes Possible Cause Solutions Fabric softener used incorrectly. Confirm and follow the instructions provided with your fabric softener. Clean and dirty clothes are being dried together. Use your dryer to dry only clean items. Soil from dirty clothes can transfer to the clean clothes in the same or later loads. Clothes were not properly cleaned or rinsed before being placed in the dryer.
Troubleshooting Problem Lint on clothes Excess static in clothes after drying Clothes have damp spots after a SENSOR DRY cycle. Possible Cause Solutions Excess static in clothes. Use a fabric softener to reduce static electricity. Be sure to follow the manufacturer’s instructions. Overdrying a load of laundry can cause a buildup of static electricity. Adjust settings and use a shorter drying time, or use SENSOR DRY cycles. Dryer is overloaded.
Troubleshooting 51 Problem Possible Cause Solutions Error code: tE1 through tE7 Temperature sensor failure. Turn off the dryer and call for service. Display shows error code: PS (electric dryers only) Power cord is connected incorrectly. Check the connection of the power cord to the terminal block. *Flow SenseTM indicator shows four bars during the drying cycle or the display shows "d80" after drying Exhaust system is too long or has too many turns/restrictions.
Troubleshooting Problem Possible Cause Solutions The display shows d90, d95 The duct work is about 90%-95% blocked.(“d90” or “d95” error code is displayed for 2 hours only) Do not use the dryer until the exhaust system has been cleaned and/or repaired. Using the dryer with a severely restricted exhaust is dangerous and could result in a fire or other property damage. House exhaust system blocked. Check the outside dryer vent while the dryer is operating to make sure there is strong airflow.
WARRANTY (USA) 53 ARBITRATION NOTICE: THIS LIMITED WARRANTY CONTAINS AN ARBITRATION PROVISION THAT REQUIRES YOU AND LG TO RESOLVE DISPUTES BY BINDING ARBITRATION INSTEAD OF IN COURT, UNLESS YOU CHOOSE TO OPT OUT. IN ARBITRATION, CLASS ACTIONS AND JURY TRIALS ARE NOT PERMITTED. PLEASE SEE THE SECTION TITLED “PROCEDURE FOR RESOLVING DISPUTES” BELOW.
WARRANTY (USA) •• Increases in utility costs and additional utility expenses. •• Repairs when your Product is used in other than normal and usual household use (e.g. commercial use, in offices and recreational facilities) or contrary to the instructions outlined in the Product’s owner’s manual. •• Costs associated with removal of your Product from your home for repairs.
WARRANTY (USA) 55 Definitions. For the purposes of this section, references to “LG” mean LG Electronics U.S.A., Inc.
LG Customer Information Center For inquiries or comments, visit www.lg.com or call: This product qualifies for ENERGY STAR in the “factory default (Home Use)” setting. Changing the factory default settings or enabling other features may increase power consumption that could exceed the limits necessary to qualify for ENERGY STAR . 1-800-243-0000 1-888-542-2623 USA CANADA Register your product Online! www.lg.
