Owner's Manual

19
Hookup and
Settings
General
Settings
(Continued)
TV
Aspect
Selects the
aspect
ratio of the connected TV
(4:3
standard or
wide).
[4:3
Letter
Box]
Select this when
connecting
to a 4:3
screen TV.
Displays
a wide
picture
with bands on
the
upper
and lower
portions
of the screen.
[4:3
Pan
Scan]
Select this when
connecting
to a 4:3
screen TV.
Automatically displays
a wide
picture
on
the entire screen and cuts off the
portions
that do
not fit.
[16:9]
Select this when
connecting
to a wide-screen
TV or TV with a wide mode function.
AV2
Connection
You can connect a decoder or other device to the
EURO AV2 DECODER socket on the back.
[Decoder]
Select
[Decoder]
if
you
connect the
recorder's EURO AV2 DECODER
jack
to a PAY-TV
or Canal Plus decoder.
[Other Device]
Select
[Other Device]
if
you
connect
the recorder's EURO AV2 DECODER
jack
to a VCR
or similar
recording
device.
Progressive
Scan
(DR687DX,
DRK687X
only)
Progressive
Scan Video
provides
the
highest quality
pictures
with less
flickering.
If
you
are
using
the COMPONENT/PROGRESSIVE
SCAN VIDEO OUT
jacks,
but are
connecting
the
recorder to a standard
(analog)
television,
set
Progressive
Scan to
[OFF].
If
you
are
using
the COMPONENT/PROGRESSIVE
SCAN VIDEO OUT
jacks
for connection to a TV or
monitor that is
compatible
with a
progressive
scan
signal,
set
Progressive
Scan to
[ON].
Note:
Progressive
Scan will be disable in the
setup
menu
when the VIDEO OUT SELECT switch on the rear
panel
is set to RGB
position.
Caution
Once the
setting
for
Progressive
Scan
output
is
entered,
an
image
will
only
be visible on a
Progressive
Scan
compatible
TV or monitor. If
you
set
Progressive
Scan to
[ON]
in
error,
you
must reset the
recorder.
First,
remove the disc in the recorder.
Next,
press
STOP
(x)
and hold it for five seconds before
releasing
it. The video
output
will be restored to the
standard
setting,
and a
picture
will once
again
be
visible on a conventional
analog
TV or monitor.
Power Save Mode
You can set
up
the unit into an economic
power
save
mode.
Nothing
is
displayed
in the
display
window
when the unit is turned off.
[OFF]
Power Save Mode is not active.
[ON]
Power Save Mode is active.
Notes:
The encoded television
signals (CANAL+
or
PREMIERE)
are not decoded in the Power Save
Mode.
The Power Save Mode is not available in the
standby
mode for the timer
recording
and when
power
off of the unit after
receiving
the encoded
television
signals (CANAL+
or
PREMIERE).
Factory
Set
If
you
need
to,
you
can reset the Recorder to all its
factory settings.
Select ''Set'' icon then
press
ENTER
and auto
setup
menu will
appear,
see
page
16.
Note:
Some
options
can not be reset.
(Rating,
Password,
and Area
Code)
Language Settings
Display
Menu
Select a
language
for the
Setup
menu and on-screen
display.
Disc Menu/Audio/Subtitle
[Original]Refers
to the
original language
in which
the disc was recorded.
[Others]
To select another
language, press
number
buttons then ENTER to enter the
corresponding
4-digit
number
according
to the
language
code list
in the reference
chapter (see page 47).
If
you
make
a mistake while
entering
number,
press
CLEAR
repeatedly
to delete numbers one
by
one then
correct it.
[Off](for
Disc
Subtitle)
: Turn off Subtitle.