Owner's Manual

22
Additional Information
Last Condition
Memory
This
player
memorizes the user
settings
for the last disc
that
you
have viewed.
Settings
remain
in
memory
even
if
you
remove the disc from the
player
or switch off the
player.
If
you
load a disc that has its
settings
memo-
rized,
the latest
stop position
is
automatically
recalled.
Notes
--
Settings
are stored
in
memory
for use
any
time.
--
This
player
does not memorize
settings
of a disc
if
you
switch off the
player
before
commencing
to
play
it.
Screen Saver
The screen saver
picture appears
when
you
leave the
DVD
Player
in
stop
mode for about five minutes.
After the Screen Saver has been
engaged
for about five
minutes,
the
DVD
Player
will
automatically
turn itself off.
Video Mode
Setting
With
certain
discs,
the
playback picture may
be flick-
ering
or Dot Crawl is shown on
straight
lines. That
means Vertical
interpolation
or De-interlace is not
perfectly
matched
with
the disc.
In
this
case,
the
picture quality may
be
improved by changing
the
video mode.
To
change
the video
mode,
press
and hold DISPLAY
about 3 seconds
during
disc
playback.
The new video
mode number selected is
displayed
on the
TV
screen.
Check whether the video
quality
has
improved.
If
not,
repeat
the above
procedure
until
picture quality
is
improved.
Video mode
change sequence:
MODE1
→
MODE2
→
MODE3
→
MODE1
If
you
turn off the
power,
the video mode
will
be back
to initial state
(MODE1).
Detailed
Descriptions
for Video Modes
MODE1: The source material of the
DVD
video
(film
material
or video
material)
is determined from disc information.
MODE2: Suitable for
playing
film
based content or video based
material recorded
by
the
progressive
scan method.
MODE3: Suitable for
playing
video based content
with
compar-
atively
little motion.
Note
The video mode
setting only
works when the
Progressive
Scan mode is set to "On"
in
the
Setup
menu.
Controlling
other TVs
with
the
remote control
You can control the sound
level,
input
source,
and
power
switch of
your
LG
TV with
the
supplied
remote
control.
You can control the sound
level,
input
source,
and
power
switch of non-LG TVs as well.
If
your
TV
is listed
in
the table
below,
set the
appropriate
manufacturer
code.
1
While
holding
down
TV
POWER
button,
press
the
number buttons to select the manufacturer code for
your
TV
(see
the table
below).
2
Release
TV
POWER button.
Code numbers of controllable TVs
If
more than one code number is
listed,
try entering
them one at a time until
you
find the one that works
with
your
TV.
Manufacturer Code Number
LG
/
GoldStar
1
(Default),
2
Zenith
1,3,4
Samsung
6,7
Sony
8,9
Hitachi
4
Note
Depending
on
your
TV,
some or all buttons
may
not
function on the
TV,
even after
entering
the correct
manufacturer code.
If
you
enter a new code
number,
the code number
previously
entered
will
be erased.
When
you replace
the batteries of the
remote,
the
code number
you
have set
may
be reset to the
default
setting.
Set the
appropriate
code number
again.
System
Select
You must select the
appropriate system
mode for
your
TV
system.
If
NO DISC
appears
in
the
display
window,
press
and hold PAUSE on the front
panel
for more than
5 seconds to be able to select a
system
(PAL,
NTSC,
or
AUTO).
?
When the selected
system
does not coincide
with
the
system
of
your
TV,
normal color
picture may
not be
displayed.
AUTO: Select when
DVD
player
is connected
with
Multi
system
TV.
NTSC: Select when
DVD
player
is connected
with
NTSC-TV.
PAL:
Select when
DVD
player
is connected
with
PAL-TV.
VCD1.1 VCD2.0 DVD
VCD1.1 CD
DVD