For U.K. Customer CUSTOMER SERVICES Tel. Fax. LGEUK SERVICE WEB-SITE P/No.: MFL61988408 : +44-(0) 844 847 LGLG(5454) : +44-(0) 844 847 1413 : http://www.lge.co.
Washing Machine OWNER’S MANUAL F8056QD(1~9)/WD-80690TDK F1056QD(1~9)/WD-10690TDK/WD-1039(1~9)TDK F1256QD(1~9)/WD-1239(1~9)TDK F1456QD(1~9)/WD-1439(1~9)TDK Thank you for buying a LG Fully Automatic Washing machine. Please read your owner’s manual carefully, it provides instructions on safe installation, use and maintenance. Retain it for future reference. Record the model and serial numbers of your washing machine.
roduct Features P Protection against creases With the alternate rotation of the drum, creasing in the laundry is minimized. Built-in heater Internal heater automatically heats the water to the best temperature on selected cycles. More economical by Intelligent Wash System Intelligent Wash System detects the amount of load and water temperature, and then determines the optimum water level and washing time to minimize energy and water consumption.
W arnings READ ALL INSTRUCTIONS AND EXPLANATION OF THE INSTALLATION BEFORE USE WARNING! For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, personal injury, or loss of life. IMPORTANT SAFETY INSTRUCTIONS WARNING : To reduce the risk of fire, electric shock, or injury to persons when using the washer, follow basic precautions, including the following: • Before installation, check exterior damages.
S pecifications ■ Name : Front loading washing machine ■ Power supply : 220-240V~,50Hz ■ Size : 600mm(W) ■ Weight/Max.Watt : 61kg / 2100W ■ Wash capacity : Refer to the Rating Label ■ Water consumption : 49 (7 /kg) 550mm(D) 850mm(H) ■ Permissible water pressure : 0.
I nstallation Install or store where it will not be exposed to temperatures below freezing or exposed to the weather. Properly ground washer to conform with all governing codes and ordinances. The base opening must not be obstructed by carpeting when the washing machine is installed on a carpeted floor.
I nstallation Installation place requirement Drain Hose Washer Laundry Tub approx. 2cm Level floor : Allowable slope under entire washer is 1˚ Power outlet : Must be within 1.5 meters of either side of location of washer. Do not overload the outlet with more than one appliance. Additional Clearance : For wall, door and floor modeling is required. (10cm : rear /2cm:right & left side) Do not place or store laundry products on top of washer at any times. They can damage the finish or controls.
nstallation I ■ Electrical connection 1. Do not use an extension cord or double adapter. 2. If the supply cord is damaged, it must be replaced by the manufacturer or its service agents or similarly qualified person in order to avoid a hazard. 3. Always unplug the machine and turn off the water supply after use. 4. Connect the machine to an earthed socket in accordance with current wiring regulations. 5. The appliance must be positioned so that the plug is easily accessible.
nstallation I Normal Tap without thread & screw type inlet hose 1. Unscrew the fixing screw to attach the tap. 2. Push the connector up till the rubber packing is in tight contact with the tap. Then tighten the 4 screws. 3. Push the water supply hose vertically upwards so that the rubber packing within in the hose can adhere completely to the tap and then tighten it by screwing it to the right. Normal Tap without thread & one touch type inlet hose (Single inlet models) 1.
I nstallation This equipment is not designed for maritime use or for use mobile installations such as caravans, aircraft etc. Turn off the stopcock if the machine is to be left for any length of time (e.g. holiday), especially if there is no floor drain(gully) in the immediate vicinity. When disposing of the appliance, cut off the mains cable, and destroy the plug Disable the door lock to prevent young children being trapped inside. Packaging material (e.g. Films, Styrofoam) can be dangerous for children.
I nstallation Level adjustment 1. Adjusting the washing machine level properly prevents excessive noise and vibration. Install the appliance on a solid and level floor surface, preferably in a corner of the room. NOTE Timber or suspended type flooring may contribute to excessive vibration and unblance errors. 2. If the floor is uneven, adjust the adjustable feet as required. (do not insert pieces of wood etc.
C are before washing Before the first washing Select a cycle (COTTON 60°C, add a half load of detergent) allow the unit to wash without clothing. This will remove residues and water from the drum that may have been left during manufacturing. Caring before washing 1. Care Labels Look for a care label on your clothes. This will tell you about the fabric content of your garment and how it should be washed. 2.
A dding detergent Adding detergent and fabric softener 1. The Dispenser Drawer • Main wash only ➔ MAX • Pre Wash + Main Wash ➔ max 2. Adding Fabric Softener • Do not exceed the maximum fill line. Close the dispenser drawer slowly. Overfilling can cause early dispensing of the fabric softener which could stain clothes. • Do not leave the fabric softener in the detergent drawer for more than 2 days. (Fabric softener could harden) • Softener will automatically be added during the last rinse cycle.
A dding detergent 3. Detergent dosage • The detergent should be used according to the instruction of the detergent manufacture. • If too much detergent is used, too many suds can occur and this will decrease the washing result or cause heavy load to the motor. • Use powder detergent only for the front loading washer. ❇ If suds occur too much, pleas reduce the detergent amount. • Detergent usage may need to be adjusted for water temperature, water hardness, size and soil level of the load.
F unction Recommended courses according to the laundry type Fabric Type Program Color fast gaments (shirts, night dresses, pajamas...) and lightly soiled white cotton(underwear...) Cotton Proper Temp. 60˚C (Cold, 30˚C, 40°C,95°C) Synthetic Polyamide, Acryic, Polyester 40˚C (Cold, 30˚C, 60°C) Cotton Quick Cotton which is lightly soiled 60˚C (Cold, 30˚C, 40°C) Quick 30 Hand Wash Wool Delicate / Rating Less than 3.0 kg Rating Less than 2.
H ow to use washer 1. Cotton automatically selected upon power on. • Press the Power button to start. • Press the Start/Pause button. • Initial conditions - Wash : main wash - Rinse : 3 times 2. Manual Selecting • Press the Power button to start. • Select the conditions which you want to use, by turning the program dial and pressing each button. For selecting the each conditions, please refer to the page16~page21 • Press the Start/Pause button.
H ow to use washer (1) Dial : Program (2) Button : Start / Pause (3) Button : Spin (4) Button : Temperature (5) Button : Power (6) Button : Medic Rinse (7) Button : Pre Wash (8) Button : Intensive Power (9) Button : Crease Care (10) Child Lock (11) Button : Time Delay Program 1. Power • Press the Power button to turn power on and off. • To cancel the Time Delay function, the power button should be pressed. 2. Initial Program • When the Power button is pressed, the washer is ready for Cotton program.
H ow to use washer Start/Pause Option • By pressing the Option button, all Option functions may be selected. 1. Start • This Start/Pause button is used to start wash cycle or pause the wash cycle. 2. Pause • If temporary stop of wash cycle is needed, press the Start/Pause button. 1. Medic Rinse • When in Pause, the power is turned off automatically after 4 minutes. • For high effectiveness or more purity in rinse operation you can choose Medic Rinse option. • NB.
H ow to use washer Child Lock If you choose to lock the buttons on the control assembly to prevent tampering this function may be selected. • Child Lock can be set by pressing the Medic Rinse button and Pre Wash button simultaneously. (About three seconds) • To change to the desired program, whilst in child lock mode. 1. Press both Medic Rinse and Pre Wash together once again. (About three seconds) 2. Press the Start/Pause button. 3. Select the desired program and press the Start/Pause button again.
H ow to use washer Spin • After selecting the spin course, the spin speed can be chosen by pressing the spin button. [F8056QD(1~9)/ WD-80690TDK] [F1056QD(1~9)/ WD-10690TDK/ WD-1039(1~9)TDK] [F1256QD(1~9)/ WD-1239(1~9)TDK] 1. Spin selection • Spin Speed is available according to the program as follows.
H ow to use washer Water Temp. • By pressing the Temp. button, the water temperature can be selected. - Cold - 30˚C / 40˚C / 60˚C / 95˚C Time Delay Preparing washing before starting “Time Delay” - Turn on the water tap. - Load laundry and close the door. • Water temperature can be selected according to the program. The required temperature lamp will light up for identification. For the more detailed information, please refer to the page14. - Place the detergent and fabric softener in the drawer.
H ow to use washer Display 3. Completion of washing • When washing cycle is completed, “ ” is displayed on the “Multi display”. 1. Special function display 4. Time left • When child lock is selected, the “ ” is displayed. • During washing cycle, the remaining washing time is displayed. • Recommended program by manufacturer. • When time delay is selected, it shows the remaining time to finish the selected program. 2.
M aintenance ❋ Before cleaning the washer interior, unplug the electrical power cord to avoid electrical shock to avoid electrical shock hazards. ❋ When disposing of the appliance, cut off the mains cable, and destroy the plug Disable the door lock to prevent young children being trapped inside. The water inlet filter -" " error message will blink on the control panel when water does not enter the detergent drawer.
M aintenance The drain pump filter ❋ The drain filter collects threads and small objects left in the laundry. Check regularly that the filter is clean to ensure smooth running of your machine. CAUTION First drain using the drain hose and then open the pump filter to remove whatever any threads or objects. Be careful when draining if the water is hot. ❋ Allow the water to cool down before cleaning the drain pump, carrying out emergency emptying or opening the door in an emergency. 1.
M aintenance ■ Dispenser drawer ❋ After a while detergents and fabric softeners leave a deposit in the drawer. • It should be cleaned from time to time with a jet of running water. • If necessary it can be removed completely from the machine by pressing the catch downwards and by pulling it out. max MAX MAX • To facilitate cleaning, the upper part of the fabric softener compartment can be removed.
M aintenance ■ Cleaning your washer 1. Exterior Proper care of your washer can extend its life. The outside of the machine can be cleaned with warm water and a neutral non abrasive household detergent. Immediately wipe off any spills. Wipe with damp cloth. Try not to hit surface with sharp objects. ❋ IMPORTANT: Do not use methylated spirits, diluents or similar products. 2. Interior Dry around the washer door opening, flexible gasket and door glass. Run washer through a complete cycle using hot water.
roubleshooting guide T ❋ This washing machine is equipped with automatic safety functions which detect and diagnose faults at an early stage and react appropriately When the machine does not function properly or does not function at all, check the following points before you contact your service provider. Symptom Possible Cause Solution Rattling and clanking noise • Foreign objects such as coins or safety pins maybe in drum or pump. Stop washer and check drum and drain filter.
T roubleshooting guide Symptom Washer does not start Possible Cause • Electrical power cord may not be plugged in or connection may be loose. Make sure plug fits tightly in wall outlet. • House fuse blown, circuit breaker tripped,or a power outage has occurred. Reset circuit breaker or replace fuse. Do not increase fuse capacity. If problem is a circuit overload, have it corrected by a qualified electrician. Turn on water supply tap. • Water supply tap is not turned on.
T roubleshooting guide Symptom Possible Cause Solution • Water supply is not adequate in area. • Water supply taps are not completely open. • Water inlet hose(s) are kinked. • The filter of the inlet hose(s) are clogged. Check another tap in the house. Fully open tap. Straighten hose(s). Check the filter of the inlet hose. • Drain hose is kinked or clogged. • The drain filter is clogged. Clean and straighten the drain hose. Clean the drain filter. • Load is too small. • Load is out of balance.
T erms of Warranty Disposal of your old appliance 1. When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC. 2. All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities. 3.
M emo 30
