OWNER'S MANUAL WASHING MACHINE Please read this manual carefully before operating your washing machine and retain it for future reference.
product Features I Protection against creases With the alternate rotation of the drum, creasing in the laundry is minimized. I Built-in heater Internal heater automatically heats the water to the best temperature on selected cycles. I More economical by Intelligent Wash System Intelligent Wash System detects the amount of load and water temperature, and then determines the optimum water level and washing time to minimize energy and water consumption.
arnings READ ALL INSTRUCTIONS AND EXPLANATION OP THE INSTALLATION BEPORE USE A WARNING! For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, personal injury, or loss of life. IMPORTANT SAFETY INSTRUCTIONS WARNING ! To reduce the risk of fire, electric shock, or injury to persons when using the washer, follow basic precautions, including the following: • Before installation, check exterior damages.
pecifications Power Plug • If the supply cord is damaged, It must be replaced by the manufacturer or Its service agents or a similarly qualified person in order to avoid a hazard. Control Panel Drum Drain Pump Filter Drain Plug Lower Cover Cap I Name : Front loading washing machine I Power supply : 220-240V~,50Hz I Size : 600mm{W) x550mm(D) x850mm{H) I Weight :62kg I Max.Watt : 2100W I Wash capacity :7kg [F14/12/1096QD(W)(A)(1~9)] I Spin speed : 0.
nstallation Install or store where It will not be exposed to temperatures below freezing or exposed to the weather. Properly ground washer to conform with all governing codes and ordinances. The base opening must not be obstructed by carpeting when the washing machine is installed on a carpeted floor. In countries where there are areas which may be subject to infestation by cockroaches or other vermin, pay particular attention to keeping the appliance and its surroundings in clean condition at all times.
nstallation Installation place requirement Level floor: Allowable slope under entire washer is 1” Power outlet: Must be within 1.5 meters of either side of location of washer. Do not overioad the outiet with more than one appliance. Additional Clearance: For wall, door and floor modeling is required. (10cm : rear /2cm:right & left side) Do not place or store laundry products on top of washer at any times. They can damage the finish or controls. ■ Positioning Install the washer on a flat hard floor.
nstallation ■ Electrical connection 1. Do not use an extension cord or double adapter. 2. If the supply cord is damaged, it must be replaced by the manufacturer or its service agents or similarly qualified person in order to avoid a hazard. 3. Always unplug the machine and turn off the water supply after use. 4. Connect the machine to an earthed socket in accordance with current wiring regulations. 5. The appliance must be positioned so that the plug is easily accessible.
nstallation Normal Tap without thread & screw type inlet hose 1. Unscrew the fixing screw to attach the tap. . Push the connector up tiii the rubber packing is in tight contact with the tap. Then tighten the 4 screws. . Push the water suppiy hose verticaiiy upwards so that the rubber packing within in the hose can adhere compieteiy to the tap and then tighten it by screwing it to the right. Fixing screw Normal Tap without thread & one touch type inlet hose 1. Untighten the upper connector 2.
nstallation This equipment is not designed for maritime use or for use mobiie instailations such as caravans, aircraft etc. Turn off the stopcock if the machine is to be ieft for any iength of time (e.g. hoiiday), especiaiiy if there is no fioor drain(guily) in the immediate vicinity. When disposing of the appiiance, cut off the mains cabie, and destroy the piug Disabie the door iock to prevent young chiidren being trapped inside. Packaging materiai (e.g. Fiims, Styrofoam) can be dangerous for chiidren.
nstallation Level adjustment 1. Adjusting the washing machine level properly prevents excessive noise and vibration. Install the appliance on a solid and level floor surface, preferably in a corner of the room. Timber or suspended type flooring may contribute to excessive vibration and unblance errors. • 2. If the floor is uneven, adjust the adjustable feet as required, (do not insert pieces of wood etc.
are before washing Before the first washing Select a cycle (COTTON 60°C, add a half load of detergent) allow the unit to wash without clothing. This will remove residues and water from the drum that may have been left during manufacturing. Caring before washing 1. Care Labels Look for a care label on your clothes. This will tell you about the fabric content of your garment and how it should be washed. 2. Sorting To get the best results, Sort clothes into loads that can be washed with the same wash cycle.
lidding detergent I Adding detergent and fabric softener 1. The Dispenser Drawer • Main wash only \ 11 / • Pre Wash + Main Wash \ I / • \ 11 / Keep all washing detergents away from children as there is danger of poisoning. Too much detergent, bleach or softener may cause an overflow. Be sure to use the appropriate amount of detergent. 2. Adding Fabric Softener • Do not exceed the maximum fill line. Close the dispenser drawer slowly.
lidding detergent 3. Detergent dosage • Detergent should be used according to the instruction of the detergent manufacture. • If too much detergent is used, too many suds can occur and this will decrease the washing result or cause heavy load to the motor. • It is recommended that you use powdered detergent for best results. • If you wish to use liquid detergent follow guidelines provided by the detergent manufacturer.
unction Recommended courses according to the laundry type Program Fabric Type Cotton Cotton Eco Color fast garments (shirts, nightdresses, pajamas, etc) and normaiiy soiied cotton ioad (underwear) Baby Care Laundry for infant Skin Care Fabrics which wiii be in direct contact with the skin, e.g. underwear, nappies, toweiling, bed linen, pillow and mattress covers Easy Care Mix Duvet Sports Wear Option Proper Temp.
unction * Water Temperature : Select the water temperature to the wash cycles. Always follow garment manufacture's care label or Instructions when laundering, * Intensive : When washing heavily soiled laundry you can Increase effectiveness by choosing “Intensive” option. * Pre Wash : If the laundry is heavily soiled, “Pre Wash” Course is recommended. * Crease Care : If you want to prevent crease, select Crease Care button.
ow to use washer SmartOiagnosis"^“ function is available only for the products with a SmartDiagnosis''’'^ mark. Cotton Eco---------------- 1 — Sportswear / Mix--------------------- \ ----------Delicate Easy Care------- --------- Wool A Duvet----------- /^ n \ - Intensive 60 Skin Care------\^\ \ _\ tAyBaby Care—\ 1- 1 -------Quick 30 w / r tè L ----- Rinse+Spin Ml 1. Cotton automatically selected upon power on. Spin Temp. 2. Manual Selecting • Press the Power button to start.
(10) (6) (2) (1) (1) (2) (3) (4) Dial : Program Button : Start/Pause Button : Spin Button : Temperature (5) (6) (7) (8) (7) (3) Button : Power Button : Medic Rinse Button : Pre Wash Button : Intensive Power (4) (8) (5) (9) (11) (12) (9) Button : Crease Care (10) Child Lock (11) Tub Clean (12) Button : Time Delay Program © Sports Wear ------Delicate ------ Wool A 1.
ow to use washer Start/Pause ► II Option Medic Rinse intensive 1. Start • This Start/Pause button is used to start wash cycle or pause the wash cycle. • By pressing the Option button, all Option functions may be selected. 2. Pause • If temporary stop of wash cycle is needed, press the Start/Pause button. 1. Medic Rinse • When in Pause, the power is turned off automatically after 4 minutes. • For high effectiveness or more purity in rinse operation you can choose Medic Rinse option. • NB.
ow to use washer Child Lock( [Sj ) Tub Clean( * ) Medic Rinse Intensive Pre Wash Crease Care ~1 r & Hr j If you choose to lock the buttons on the control assembly to prevent tampering this function may be selected. Tub Clean course can be set by pressing and holding Intensive and Crease Care button simultaneously. • Child Lock can be set by pressing the Medic Rinse button and Pre Wash button simultaneously. (About three seconds) When Tub Clean course is set, display “ tci.
ow to use washer Spin( ■[§.) 1400 I 1200 800 I 800 800 400 After selecting the spin course, the spin speed can be ' 1000 400 i 400 No Spin I No Spin Rinse Hold I Rinse Hold ' Rinse Hold Spin Spin Spin chosen by pressing the spin button. No Spin [F1496Q/TD(W)(A (1-9)] [F1296Q/TD(W)(A (1-9)] [F1096Q/TD(W)(A (1-9)] 1. Spin selection 2. No spin • Spin Speed is avaiiable according to the program as foiiows. • If No spin is selected, the washer stops after draining water.
ow to use washer Water Temp. Time Delay • By pressing the Temp, button, the water temperature can be selected. - Cold - 20T / 40’C / 60T / 95’C D-nn J-UU lime Delay c-nn D-UU Preparing washing before starting “Time Delay” - Turn on the water tap. - Load laundry and close the door. - Place the detergent and fabric softener in the drawer. • Water temperature can be selected according to the program. The required temperature lamp will light up for identification.
ow to use washer Display 3. Completion of washing • When washing cycle is completed, " p ” is displayed on the “Multi display”. 1. Special function display 4. Time left • When child lock is selected, the • During washingI cycle, ( the remaining washing time is displayed. 'll" • When time delay is selected, it shows the remaining time to finish the selected program. 2. Self diagnosis display • If the machine encounters a fault during operation, the associated fault will be displayed.
aintenance ^ Before cleaning the washer interior, unplug the electrical power cord to avoid electrical shock to avoid electrical shock hazards. 0 When disposing of the appiiance, cut off the mains cable, and destroy the plug Disable the door lock to prevent young children being trapped inside. ■ The water inlet filter -" l£ " error message will blink on the control panel when water does not enter the detergent drawer.
aintenance The drain pump filter * The drain filter collects threads and small objects left In the laundry. Check regularly that the filter is clean to ensure smooth running of your machine. A CAUTION First drain using the drain hose and then open the pump filter to remove whatever any threads or objects. Be careful when draining if the water is hot. A CAUTION Do not open filter in half only. Filter must be turned off and closed fully to avoid leakage.
aintenance ■ Dispenser drawer • After a while detergents and fabric softeners leave a deposit in the drawer. • it should be cleaned from time to time with a jet of running water. • If necessary it can be removed compieteiy from the machine by pressing the catch downwards and by puiiing it out. • To facilitate cleaning, the upper part of the fabric softener compartment can be removed.
aintenance ■ Cleaning your washer 1. Exterior Proper care of your washer can extend its life. The outside of the machine can be cleaned with warm water and a neutral non abrasive household detergent. Immediately wipe off any spills. Wipe with damp cloth. Try not to hit surface with sharp objects. ^ IMPORTANT: Do not use methylated spirits, diluents or similar products. 2. Interior Dry around the washer door opening, flexible gasket and door glass. Run washer through a complete cycle using hot water.
roubleshooting guide * This washing machine is equipped with automatic safety functions which detect and diagnose faults at an early stage and react appropriately When the machine does not function properly or does not function at all, check the following points before you contact your service provider. Symptom Possible Cause Solution Rattling and clanking noise • Foreign objects such as coins or safety pins maybe in drum or pump. Stop washer and check drum and drain filter.
roubleshooting guide Symptom Washer does not start. Possible Cause • Electrical power cord may not be plugged in or connection may be loose. Make sure plug fits tightly in wall outlet. • House fuse blown, circuit breaker tripped,or a power outage has occurred. Reset circuit breaker or replace fuse. Do not increase fuse capacity. If problem is a circuit overload, have it corrected by a qualified electrician. Turn on water supply tap. • Water supply tap is not turned on. Washer will not spin.
roubleshooting guide Symptom Possible Cause Solution • Water supply is not adequate in area. • Water supply taps are not completely open. • Water inlet hose(s) are kinked. • The filter of the inlet hose(s) are clogged. Check another tap in the house. Fully open tap. Straighten hose(s). Check the filter of the inlet hose. • Drain hose is kinked or clogged. • The drain filter is clogged. Clean and straighten the drain hose. Clean the drain filter. • Load is too small. • Load is out of balance.
roubleshooting guide ^ SmartDiagnosis™ function is available only for the products with a SmartDIagnosis™ mark. NOTE In case of a mobile phone with static option, the smart diagnosis function might not operate. ■ Using SmartDiagnosis™ • Only use this feature when instructed to do so by the call center. The transmission sounds similar to a fax machine, and so has no meaning except to the call center. ♦ SmartDiagnosiscannot be activated it the washer does not power up.
erms of Warranty Disposal of your old appliance 1. When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC. 2. All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities. 3.
LG Life's Good CUSTOMER SERVICES Fax. LGEUK SERVICE WEB-SITE Tel. +44-(0) 844 847 LG LG (5454) +44-{0) 844 847 1413 http://www.lge.co.uk For U.K.
