The FLATRON LCD 295LM Flat Panel Monitor has an active matrix TFT (Thin-Film Transistor) LCD (Liquid Crystal Display). Features The FLATRON LCD 295LM is a 22-inch (55.8cm viewable) intelligent micro- processor based monitor. This monitor can be connected to a VCR or DVD. The monitor has two signal (D-sub and DVI-D) so that it can support both an existing analog input (D-sub) and an advanced standard digital input (DVI-D).
Description of Controls Front Panel Controls Remote Control Sensor SET Button MENU Button MENU SOURCE DOWN/UP VOLUME Power Button SET SOURCE Selection DOWN/UP Button ( ) VOLUME Control SOURCE ( ) Power Indicator Buttons Buttons Function SOURCE Selection Button Use this button to select SOURCE input signal.
Description of Controls Rear Panel Controls Connected to another object (stand type and wall-mounted type optional) -- USB DC15V upstream port ANT D USB downstream Locking slot connected to can Rear Cover most Composite Input DC Power Connector be Video D-sub Connector a locking cable that purchased separately at computer Output Jack Headphone/Earphone Output Jack DC15V D S-Video Video Sound IN LR PC Audio Audio IN LR PC Sound S-Video Input Jack DVI-D Connector Sound(L/R) I
Description of Controls For the detailed instruction for each button of the remote control, refer to the appropriate pages in this manual. Remote Controller Power Button AUTO Button PAGE A2 This function is suitable for analog signal input only. This The buttons cannot be button is for the automatic set in this model. adjustment of the screen position, clock and phase. Note: Some signal from some graphics boards may not function properly.
Description of Controls Insert the batteries into the remote control to operate the monitor. This section shows you how to the remote control. Preparing the Operating with the Remote Control Make sure to match the + Point the remote control at the remote sensor and and press the buttons. - the batteries to the marks SOURCE 3. Remote Control 1. Open the battery cover. 2. Insert batteries (AAA size). on use inside the battery compartment. Close the cover.
the Monitor Connecting To set up the monitor, ensure that the power is turned off to the monitor, computer system, and other attached devices. Remove the rear cover of the monitor to connect the cables and connect the cables to the monitor with it lying on a cushion or a cloth. Rear Cover Follow these steps: Connecting the Speakers Attach the speakers to the monitor as shown positions.
Connecting the Monitor 1 Figure DC Power DVI-D connector connector PC Audio IN DC15V S-Video D 3 Video Sound IN LR There should be DVI-Dporton PC Audio Audio IN LRANT the 1 computer 5 2 Audio Cable 4 AC Power Cord adapter DC Power Figure Signal Cable D-sub connector connector 2 DVI-D PC Audio IN DC15V D S-Video Video Sound IN LR PC Audio Audio N LRANT 1 3 5 Power Cord D-sub 2 Audio Cable 4 AC adapter Signal Cable MAC6 MAC Adapter 2' Cable Signal 4.
Making use of USB (Universal Serial Bus) (Universal Serial Bus) is an innovation in connecting your different desktop peripherals conveniently to your computer. By using the USB, you will be able to connect your mouse, keyboard, printer, and other peripherals to your monitor instead of having to connect them to your computer. This will give you greater flexibility in setting up your system.
Connection of external equipment Connecting the VCR/DVD 1. Connect the audio/video output input ports of the jacks of the VCR/DVD to the corresponding set. If you connect the S-Video input port to external equipment, you can enjoy high definition display.
On Screen Display (OSD) Control Adjustment Making adjustments to the image size, position and operating parameters of the monitor are quick and easy with the On Screen Display Control system. A quick example is given below to familiarize you with the use of the controls. Following section is an outline of the available adjustments and selections you can make using the OSD.
On Screen You were Display(OSD) introduced to the Selection and Adjustment procedure of selection and adjusting an item using the OSD system. Listed below are shown are icons, icon names, and icon descriptions of the items that the the Menu. on Adjusting the Screen when Using a Computer Note : When PIP items can OSD input is set as a digital signal, only the BRIGHTNESS, SETUP, be adjusted. You do not need to adjust the other items.
On Screen Display(OSD) OSD Selection and Adjust Description AUTO RGB This function is suitable for analog signal input only. This button is for the TRACKING Image AUTO OFF automatic Color Position Adjustment CLOCK 50 PHASE 50 position, CLOCK Tracking adjustment of the phase. screen clock and To minimize any vertical bars stripes visible on the screen Setup background.The horizontal change. or screen size will also PIP PHASE adjust the focus of the display.
On Screen Display(OSD) OSD RGB Adjust PIP Image PIP ON/OFF OFF Color Position PIP SOURCE V1(AV) PIP SIZE LARGE PIP POSITION Tracking PIP SOUND Setup PIP Selection and OFF Adjustment Description This PIP (Picture-in-Picture) function allows the image from the VCR or DVD to be displayed on sub-screen while you are using a computer. PIP ON/OFF To select the sub-screen on/off. PIP SOURCE To select an input :V1 (AV) / V2 (S) PIP SIZE To a PIP IMAGE signal for PIP.
On Screen Display(OSD) Selection and Adjustment Adjusting the Screen when Using VCR/DVD ( V1 / V2 ) Adjust OSD Description CONTRAST ADJUSTMENT Adjustment Audio Setup CONTRAST 53 BRIGHTNESS 70 SHARPNESS 50 COLOR 50 TINT 50 the desired. display to Adjust BRIGHTNESS Used to adjust the the contrast brightness of the screen. SHARPNESS To adjust the clearness of the COLOR To adjust the color to desired level. TINT To adjust the tint to desired level.
display modes listed below are the most commonly used modes and are set as factory defaults. The monitor automatically recognizes most input data modes, and displays centered images with the proper sizing. The If the to screen size is inappropriately set or the display is not centered, you need readjust the parameters of the monitor using the OSD (on-screen display). Display Modes (Resolution) 123456789 10 11 12 13 14 15 *16 VESA, IBM 640 x 350 31.469 70 VESA VESA VESA VESA 640 x 480 31.
Troubleshooting Check the following before calling for service. Display Position is incorrect. Select AUTO in the OSD menu. If the results are unsatisfactory, adjust the image position using the position icon in the on screen display. On the screen background, vertical bars or stripes are visible. Select AUTO in the OSD menu. If the results are unsatisfactory, decrease the vertical bars CLOCK icon in the on screen display. in any Any horizontal noise appearing portraid.
Specifications Display Sync Input Video Input Type 22inch (55.8cm) Wide SXGA TFT LCD Viewable Size Anti-Glare coating 22inch (55.8cm) Viewing Angle(max.) Pixel pitch 70˚ True color 16.7 million color Horizontal Freq. Vertical Freq. Input form 30kHz Signal input Input Form pin D-Sub connector/DVI-D connector Separate, RGB Analog, 0.
