Table of Contents Introduction Introduction Important Installation Operation Precautions Connecting the Monitor Location and Function of Controls Control Panel Function Technical Information On Screen Display (OSD) Control Adjustment On Screen Display(OSD) Selection and Adjustment Energy Saving Design Low Radiation Compliance (MPR II), Self Diagnostics Messages and DDC (Display Data Channel) Video Memory Modes Troubleshooting Service Specifications Appendix Communications Regulation
Introduction The FLATRON LCD 575MS Flat Panel Monitor has TFT (Thin-Film Transistor) an active matrix LCD (Liquid Crystal Display). designed for use in small working areas or for those who need more working space on the desk. This monitor is Features The FLATRON LCD 575MS is intelligent micropro-cessor based a 15-inch (15 inches viewable) monitor.
Precautions Important This unit has been engineered and manufactured to assure your personal safety, but improper use can result in potential electrical shock or fire hazard. In order not to defeat the safeguards incorporated in this monitor, observe the following basic rules for its installation, use, and servicing. Also follow all warnings and instructions marked directly on your monitor. On Safety Use only the power cord supplied with power cord, make the unit.
Precautions Important On Installation Do not bring magnetic devices such picture tube. as magnets or motors near the Do not allow anything to rest upon or roll over the power cord, and do not monitor where the power cord is subject to damage. place the Do not this monitor use near water such as near a in basement, bathtub, washbowl, kitchen sink, laundry tub, Monitors provided with ventilation openings in the cabinet to allow the generated during operation.
Installation Connecting the Monitor Connection to any IBM VGA PC compatible monitor, ensure that the power is turned off to the monitor, computer system, and other attached devices, then follow To set up the these steps: system 1. Place the monitor in a convenient, well-ventilated location near your computer. 2. Power off both the monitor and Computer. 3. Slightly press and pull the latch on Stand cover. 4.
Installation Connecting the Monitor Connecting to an Apple Figure shows the connection to an Apple Macintosh, using a separately purchased adapter. For more information on adapter requirements, contact your authorized dealer, reseller, or service provider. Macintosh PC 1. Place the monitor in a convenient, well-ventilated location near your computer. 2. Power off both the monitor and Computer. 3. Slightly press and pull the latch on Stand cover. 4.
Operation Location and Function of Controls Front View Power Button Power Indicator OSD Button AUTO/SET Button Buttons Rear View DC Power Connecter - D-Sub + Signal Stand Cover A6 Connector
Operation Control Panel Function Front Panel Controls OSD Button Power Indicator Use this button to enter The power indicator or exit the light is shown in the power button. This indicator on screen lights up green when the monitor operates normally. If the monitor is in DPM display. (Energy Saving) mode (stand-by/ suspend/power off), this indicator color changes to amber. * AUTO Function When you press AUTO/SET button before using OSD menu, the screen disappears momentarily.
Operation On Screen Display (OSD) Control Adjustment Making adjustments to the image size, position and operating parameters of the monitor are quick and easy with the On Screen Display Control system. A quick example is given below to familiarize you with the use of the controls. Following section is an outline of the available adjustments and selections you can make using the OSD. NOTE Allow the monitor to stabilize for at least 30 minutes before making image adjustment.
Operation On Screen Display(OSD) Selection and Adjustment You item introduced to the were procedure of selection and adjusting an using the OSD system. Listed below items that are are OSD the shown icons, icon names, and icon descriptions of the on the Menu. Adjust Description Brightness BRIGHTNESS / CONTRAST BRIGHTNESS/CONTRAST Used to adjust the of the screen. 88 brightness 100 Contrast Adjust the display to the contrast desired.
Operation On Screen Display(OSD) Selection and Adjustment OSD Adjust Description CLOCK TRACKING To minimize any vertical bars or stripes visible on the screen background.The CLOCK PHASE horizontal size will also screen change. TRACKING PHASE To adjust the focus of the display. This item allows you to remove and clear image any horizontal noise sharpen the or of characters.
071B Energy Saving Design complies with the EPA's Energy Star program, which is a program designed to have manufacturers of computer equipment build circuitry into their products to reduce power consumption during time of This monitor non-use.
Technical Information Low Radiation Compliance (MPR II), Self Diagnostics Messages and DDC (Display Data Channel) Low Radiation This monitor meets Compliance (MPR II) Sweden, limit the Frequency (ELF) Self one of the strictest guidelines available today for low radiation emissions, offering the user extra shielding and an antistatic screen coating.
Video Memory Modes The monitor has 26 memory locations for display are factory preset to popular video modes. modes, 16 of which Display Modes (Resolution) VGA 640 x 350 31.47 70 VGA 720 x 400 31.47 70 123456789 VGA 640 x 480 31.47 60 MAC 640 x 480 35.00 67 VESA 640 x 480 37.50 75 VESA 640 x 480 43.27 85 VESA 800 x 600 35.16 56 VESA 800 x 600 37.88 60 MAC 800 x 600 48.08 72 10 VESA 800 x 600 46.88 75 11 VESA 800 x 600 53.
Technical Information Troubleshooting Check the Display following before calling for service. Position is incorrect. Push the AUTO/SET Button. If the results position On the unsatisfactory, adjust the image position using position icon in the on screen display. are and V screen background, vertical bars or stripes are the H visible. Push the AUTO/SET Button.
Service Unplug the monitor from the wall outlet and refer servicing to qualified service personnel when : The power cord or plug is damaged or frayed. Liquid has been spilled into the monitor. The monitor has been exposed to rain or water. The monitor does not operate normally following the operating instructions. Adjust only those controls that are covered in the operating instructions.
Technical Information Specifications Sync Signal Types Priority Type 1 (N.C Signal Connector Pin Assignment Separate Sync. : No V.Sync. H. V. Sync. Sync. Connection) 15pin VGA Connector 5 1 6 10 15 11 Pin NOTE Adapter Pin Signal(D-Sub) 12345678 9 N.C. Green 10 Ground Blue 11 Ground Ground 12 SDA Self-Test 13 H. Sync. Red Ground 14 V. Sync. Green Ground 15 SCL ground on the PC side. Input AC 100-240V, 50-60Hz, 81-101VA, 1.2A 0.
Technical Information Specifications Display 15inch Type (38.1cm) Flat coating (38.1cm) Panel Active matrix-TFT LCD Anti-Glare Sync Input Viewable Size 15inch Pixel 0.297 pitch Input Horizontal 31kHz 69kHz Vertical 56Hz 85Hz Display Input Freq. Freq. Area Power Input Weight Tilt (Automatic) (Automatic) Separate, TTL, Positive/Negative 15 pin D-Sub connector - - 304.1 Form Resolution Dimensions 0.297mm 262,144 color Input form Signal input Video x True color x 228.
Communications Regulation Information FCC Compliance Statement This equipment has been tested and found to comply within the limits of a digital device pursuant to Part 15 of the FCC Rules. These limits designed to provide reasonable protection against harmful interference Class B are in a residential installation.
Appendix Environmental Congratulations! Labelling of Personal Computers just purchased a TCO'99 approved and labelled product! Your provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products.
Environmental What does Labelling of labelling The environmental demands involve? of impose Personal restrictions on Computers the presence and use heavy metals, brominated and chlorinated flame retardants, CFCs (freons) and chlorinated solvents, among other things. The product must be recycling and the manufacturer is obliged to have an policy which must be adhered to in each country where company implements its operational policy.
Environmental Labelling of The relevant TCO'99 demand requires Personal that Computers plastic components weighing than 25 grams must not contain flame retardants with organically bound bromine or chlorine. Flame retardants are allowed in the printed more circuit boards since no substitutes are available. Cadmium** Cadmium is present in rechargeable batteries and in the colour-generating layers of certain computer displays. Cadmium damages the nervous system and is toxic in high doses.
