Table of Contents Introduction Introduction Important Precautions Installation Connecting the Monitor Making use of USB(Universal Operation Serial Bus) Location and Function of Controls Control Panel Function Technical Information On Screen Display (OSD) Control Adjustment On Screen Display(OSD) Selection and Adjustment Energy Saving Design Low Radiation and DDC Compliance (MPR II), Self Diagnostics Messages (Display Data Channel) Video Memory Modes Troubleshooting Service Specifica
Introduction The FLATRON LCD 577LM Flat Panel Monitor has an active matrix LCD TFT (Thin-Film Transistor) (Liquid Crystal Display). designed for use in small working areas or for those who need more working space on the desk. This monitor is Features The FLATRON LCD 577LM is a intelligent micropro-cessor based USB(Universal Serial Bus) ports for the USB cable and hub. You 15.1-inch (15.1 inches viewable) monitor.
Important Precautions This unit has been engineered and manufactured to assure your personal safety, but improper use can result in potential electrical shock or fire hazard. In order not to defeat the safeguards incorporated in this monitor, observe the following basic rules for its installation, use, and servicing. Also follow all warnings and instructions marked directly on your monitor. On Safety Use only the power cord supplied with power cord, make the unit.
Important Precautions On Installation Do not bring magnetic devices such picture tube. as magnets or motors near the Do not allow anything to rest upon or roll over the power cord, and do not monitor where the power cord is subject to damage. place the Do not this monitor use near water such as near a in basement, bathtub, washbowl, kitchen sink, laundry tub, Monitors provided with ventilation openings in the cabinet to allow the generated during operation.
Installation Connecting the Monitor monitor, ensure that the power is turned off to the monitor, computer system, and other attached devices, then follow To set up the Connection to any IBM VGA PC and APPLE these steps: Macintosh PC Power off both the monitor and computer. To adjust height of your monitor, unlock the stand lock stand. Push the stand lock at arrows shown(figure A). Connect one end of the monitor on the rear panel of the monitor.
Installation Connecting the Monitor Connection the Audio 1. Connect the 2. Connect the one end of Audio DC power cable,which is attached on the speaker to AUDIO DC OUT connector 1 and the other end to DC 24V connector 2 on the back of the speaker.Then connect the audio cable port which is directly connected to the speaker to AUDIO L-OUT port 3 3. Connect the audio cable from the Speaker's AUDIO IN port audio output port of your computer's sound card. speaker as described in below picture. .
Installation Making use of USB (Universal Serial Bus) (Universal Serial Bus) is an innovation in connecting your different desktop peripherals conveniently to your computer. By using the USB, you will be able to connect your mouse, keyboard, printer, and other peripherals to your monitor instead of having to connect them to your computer. This will give you greater flexibility in setting up your system.
Installation Making use of USB (Universal Serial Bus) Example of connection SOUND SOUND scanner monitor computer keyboard mouse printer NOTE To activate the USB hub function, the monitor must be connected to compliant PC(OS) or another hub with the USB cable(enclosed). a USB When connecting the USB cable, check that the shape of the connector at the cable side matches the shape at the connecting side.
Operation Location and Function of Controls Front View Speaker SOUND SOUND Power Button OSD Button Power Indicator Buttons AUTO/SET Button Rear View Stand Lock 24 OUT AUDOI DC DC Power Connector Audio DC Power Cable Audio Cable 24V DC Power Connecter - Audio Buttons USB downstream port A8 + USB upstream port
Operation Control Panel Function Front Panel Controls OSD Button Power Indicator Use this button to enter The power indicator or exit the light is shown in the power button. This indicator on screen lights up green when the monitor operates normally. If the monitor is in DPM display. (Energy Saving) mode (stand-by/ suspend/power off), this indicator color changes to amber. * AUTO Function When you press AUTO/SET button before using OSD menu, the screen disappears momentarily.
Operation Display (OSD) Control Adjustment On Screen Making adjustments to the image size, position and operating parameters of the monitor are quick and easy with the On Screen Display Control system. A quick example is given below to familiarize you with the use of the controls. Following section is an outline of the available adjustments and selections you can make using the OSD. NOTE Allow the monitor to stabilize for at least 30 minutes before making image adjustment.
Operation On Screen Display(OSD) Adjustment You item introduced to the were Selection and procedure of selection and adjusting an using the OSD system. Listed below items that are are OSD the shown icons, icon names, and icon descriptions of the on the Menu. Adjust Description Brightness BRIGHTNESS / CONTRAST BRIGHTNESS/CONTRAST Used to adjust the of the screen. 88 brightness 100 Contrast Adjust the display to the contrast desired.
Operation On Screen Display(OSD) Adjustment Selection and Adjust OSD Description CLOCK TRACKING To minimize any vertical bars or stripes visible on the screen background.The CLOCK PHASE horizontal size will also screen change. TRACKING PHASE adjust the focus of the display. This item allows you To to remove and clear image of characters. LANGUAGE To choose the SETUP LANGUAGE ENGLISH IMAGE SIZE FULL BEEP ON OSD ROTATE OFF language which the control in names are displayed.
Energy Saving Design complies with the EPA's Energy Star program, which is a program designed to have manufacturers of computer equipment build circuitry into their products to reduce power consumption during time of This monitor non-use.
Technical Information Low Radiation Compliance (MPR II), Self Diagnostics Messages and DDC (Display Data Channel) Low Radiation This monitor meets Compliance (MPR II) Sweden, limit the Frequency (ELF) Self one of the strictest guidelines available today for low radiation emissions, offering the user extra shielding and an antistatic screen coating.
Video Memory Modes The monitor has 26 memory locations for display are factory preset to popular video modes. modes, 16 of which Display Modes (Resolution) VGA 640 x 350 31.47 70 VGA 720 x 400 31.47 70 VGA 640 x 480 31.47 60 MAC 640 x 480 35.00 67 VESA 640 x 480 37.50 75 VESA 640 x 480 43.27 85 VESA 800 x 600 35.16 56 VESA 800 x 600 37.88 60 MAC 800 x 600 48.08 72 10 VESA 800 x 600 46.88 75 11 VESA 800 x 600 53.
Technical Information Troubleshooting Check the following before calling for service. Display Position is incorrect. Push the AUTO/SET Button. If the results are unsatisfactory, and V position On the screen position icon in the adjust the on screen background, vertical bars image position using display. or stripes are visible. Push the AUTO/SET Button.
Service Unplug the monitor from the wall outlet and refer servicing to qualified service personnel when : The power cord or plug is damaged or frayed. Liquid has been spilled into the monitor. The monitor has been exposed to rain or water. The monitor does not operate normally following the operating instructions. Adjust only those controls that are covered in the operating instructions.
Technical Information Specifications Sync Signal Types Priority Type 1 (N.C Signal Connector Pin Assignment : Separate Sync. No V.Sync. H. V. Sync. Sync. Connection) 15pin VGA Connector 5 1 6 10 15 11 Pin NOTE Adapter Pin Signal(D-Sub) 12345678 9 N.C. Green 10 Ground Blue 11 Ground Ground 12 SDA Self-Test 13 H. Sync. Red Ground 14 V. Sync. Green Ground 15 SCL ground on the PC side. Input AC 100-240V, 50-60Hz, 1.2A - 0.
Technical Information Specifications Display 15.1inch Viewable Size (38.35cm) Flat coating 15.1inch (38.35cm) Pixel 0.3 Type Panel Active matrix-TFT LCD Anti-Glare Sync Input Video Input Audio pitch x 0.3mm True color 16.7 million color Horizontal Freq. Vertical Freq. Input form Signal input 31kHz 69kHz Display Area 307 Input Form Separate, Resolution (max.) VESA 1024 (Automatic) (Automatic) Separate, TTL, Positive/Negative 15 pin D-Sub connector - 56Hz 85Hz - x 230mm / 12.
Appendix Communications FCC Compliance Statement Regulation Information equipment has been tested and found to comply within the limits of a Class digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential This B installation.
Appendix Environmental Congratulations! Labelling of Personal Computers just purchased a TCO'99 approved and labelled product! Your provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products.
Environmental What does Labelling of Personal Computers labelling The environmental demands involve? of impose restrictions on the presence and use heavy metals, brominated and chlorinated flame retardants, CFCs (freons) and chlorinated solvents, among other things. The product must be recycling and the manufacturer is obliged to have an policy which must be adhered to in each country where company implements its operational policy.
Environmental Labelling of Personal Computers The relevant TCO'99 demand requires that plastic components weighing than 25 grams must not contain flame retardants with organically bound bromine or chlorine. Flame retardants are allowed in the printed more circuit boards since no substitutes are available. Cadmium** Cadmium is present in rechargeable batteries and in the colour-generating layers of certain computer displays. Cadmium damages the nervous system and is toxic in high doses.
