Table of Contents Introduction Introduction ENGLISH Important Precautions Installation Connecting the Monitor Making Operation of USB (Universal Serial Bus) Feature use Location and Function of Controls Control Panel Function Technical Information On Screen Display (OSD) Control Adjustment On Screen Display(OSD) Selection and Adjustment Energy Saving Design Low Radiation and DDC Compliance (MPR II), Self Diagnostics Messages (Display Data Channel) Video Memory Modes Troubleshooting
Introduction Introduction The FLATRON LCD 882LE Flat Panel Monitor has an active matrix LCD TFT (Thin-Film Transistor) (Liquid Crystal Display). designed for use in small working areas or for who need more working space on the desk. This monitor is Features The FLATRON LCD 882LE is a 18.1-inch (18.1 inches viewable) those intelligent microprocessor based monitor.
Important Precautions This unit has been engineered and manufactured to assure your personal safety, improper use can result in potential electrical shock or fire hazard. In order not to defeat the safeguards incorporated in this monitor, observe the following basic rules for its installation, use, and servicing. Also follow all warnings and instructions marked directly on your monitor. but On Safety Use only the power cord supplied with the unit.
Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord, and do place the monitor where the power cord is subject to damage. Do not use this monitor near water in such as near a not bathtub, washbowl, kitchen sink, laundry tub, Monitors provided with ventilation openings in the cabinet to allow the generated during operation. If these openings are blocked, are a wet basement, or near a swimming pool.
Installation Connecting the Monitor monitor, ensure that the power is turned off to the monitor, computer system, and other attached devices, then follow To set up the these steps: 1. Place the monitor in convenient, well-ventilated location a near your computer. 2. Connect the signal cable. When Connect panel panel PC connecting the .......... signal cable to the connector tighten Dsub the signal screws. to the DVI ..........
Installation Connecting the Monitor Dsub to DVI 2 Figure Dsub 3 4 Power Cord AC Dsub 2 adapter Signal Cable Dsub to DVI Figure figure3 shows the connection Apple Macintosh, using a separately purchased adapter. For more information on adapter requirements, contact your Adapter for supporting dual 1 The analog signals Dsub 5 NOTE Adapter for supporting dual 1 Dsub 3 analog signals to an authorized dealer, reseller, or Dsub service provider.
Installation Making use of USB (Universal Serial Bus) Feature (Universal Serial Bus) is an innovation in connecting your different desktop peripherals conveniently to your computer. By using the USB, you will be able to connect your mouse, keyboard, printer, and other peripherals to your monitor instead of having to connect them to your computer. This will give you greater flexibility in setting up your system.
Installation Making use of USB (Universal Serial Bus) Feature Example of connection monitor scanner computer keyboard mouse printer NOTE To activate the USB hub function, the monitor must be connected to compliant PC(OS) or another hub with the USB cable(enclosed). a USB When connecting the USB cable, check that the shape of the connector at the cable side matches the shape at the connecting side.
Operation Location and Function of Controls Front View OSD SOURCE/SET Power Button Power Indicator OSD Button SOURCE/SET Button Buttons Rear View Dsub DVI-Iport (Digital / Analog) Signal port USB upstream port USB downstream ports DC Power port - A8 +
Operation Control Panel Function Front Panel Controls Buttons OSD Button Use this button to enter the or exit Use these buttons to choose Use this button to turn adjust items screen display. the monitor or on screen Power Button in the on on or off. display. OSD Brightness and Contrast can be adjusted directly without entering the On Screen Display (OSD) system.
Operation On Screen Display (OSD) Control Adjustment Making adjustments to the image size, position and operating parameters of the monitor are quick and easy with the On Screen Display Control system. A quick example is given below to familiarize you with the use of the controls. Following section is an outline of the available adjustments and selections you can make using the OSD. NOTE Allow the monitor to stabilize for at least 30 minutes before making image adjustment.
Operation On Screen Display(OSD) Adjustment You OSD item SOURCE/SET introduced to the were OSD procedure of selection and adjusting an using the OSD system. Listed below items that SOURCE/SET Selection and are are the icons, icon names, and icon descriptions of the shown OSD on the Menu. Adjust Description Brightness BRIGHTNESS / CONTRAST BRIGHTNESS/CONTRAST Used to 100 adjust the brightness of the screen. 100 Contrast the desired.
Operation On Screen OSD OSD Display(OSD) Adjustment SOURCE/SET Selection and SOURCE/SET OSD Adjust Description CLOCK TRACKING To minimize any vertical bars or stripes visible on the screen horizontal background.The CLOCK size will also screen PHASE change. TRACKING PHASE adjust the focus of the display. This item allows you To to any horizontal noise sharpen the remove and clear image or of characters. Phase adjustment should be adjusting the Clock.
Energy Saving Design complies with the EPA's Energy Star program, which is a designed to have manufacturers of computer equipment build circuitry into their products to reduce power consumption during time of This monitor program non-use. This monitor also goes into its energy saving mode if you exceed the monitor's operating limits, such as the maximum resolution of 1280x1024 or the frequency refresh rates of 30-80kHz horizontal or 56-85Hz vertical.
Low Radiation Compliance (MPR II), Self Diagnostics Messages and DDC (Display Data Channel) Low Radiation Compliance (MPR II) This monitor meets one of the strictest guidelines available today for low radiation emissions, offering the user extra shielding and an antistatic screen coating. These guidelines, set forth by a government agency in amount of emission allowed in the Extremely Low Frequency (ELF) and Very Low Frequency (VLF) electromagnetic range.
Video Memory Modes The monitor has 26 memory locations for display are factory preset to popular video modes. modes, 16 of which Display Modes (Resolution) 123456789 640 x 350 31.469 70 VGA 720 x 400 31.468 70 VGA 640 x 480 31.469 60 VESA 640 x 480 37.500 75 VESA 640 x 480 43.269 85 VESA 800 x 600 37.879 60 VESA 800 x 600 46.875 75 VESA 800 x 600 53.674 85 x 624 MAC 832 49.725 75 10 VESA 1024 x 768 48.363 60 11 VESA 1024 x 768 60.
Technical Information Troubleshooting Check the following before calling for service. Display Position is incorrect. Select AUTO from the OSD menu, and press to activate the function. If the results are unsatisfactory, adjust the image position using the H position and V position icon in the on screen display. On the screen background, vertical bars or stripes are visible. Select AUTO from the OSD menu, and press to activate the function.
Service Unplug the monitor from the wall outlet and refer servicing to qualified service personnel when : The power cord or plug is damaged or frayed. Liquid has been spilled into the monitor. The monitor has been exposed to rain or water. The monitor does not operate normally following the operating instructions. Adjust only those controls that are covered in the operating instructions.
Technical Information Specifications 15pin VGA Connector Signal Connector Pin Assignment 5 Pin Red Video 12345678 1 6 10 11 15 NOTE 8 917 16 24 C5 Pin Blue Video 11 Ground 12 SDA Ground 13 H. Sync. Red Ground 14 V. Sync. Green Ground 15 SCL Blue Ground ground Adapter the PC side.
Technical Information Specifications Display Type 18.1inch (45.97cm) Flat Panel Active matrix-TFT LCD Viewable Size Anti-Glare coating 18.1inch (45.97cm) Viewing Angle (max.) 80˚ (Left / Right / Up / Down) Pixel pitch 0.28 x 0.28mm Sync Input Video Power Input Input 16.7 million color Horizontal Freq. Vertical Freq. Input form 30kHz Signal input Input Form pin D-Sub connector / DVI I connector (Digital/Analog) Separate, RGB Analog, 0.
Communications FCC Compliance Statement Regulation Information This equipment has been tested and found to comply within the limits of a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Appendix Environmental Congratulations! Labelling of Personal Computers just purchased a TCO'99 approved and labelled product! Your provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products.
Environmental What does Labelling of Personal Computers labelling The environmental demands involve? of heavy metals, brominated and chlorinated flame retardants, CFCs (freons) and chlorinated solvents, among other things. The product must impose restrictions on the presence and use prepared for recycling and the manufacturer is obliged to have an policy which must be adhered to in each country where the company implements its operational policy.
Environmental Labelling of Personal Computers The relevant TCO'99 demand requires that plastic components weighing than 25 grams must not contain flame retardants with organically bound bromine or chlorine. Flame retardants are allowed in the printed more circuit boards since no substitutes are available. Cadmium** Cadmium is present in rechargeable batteries and in the colour-generating layers of certain computer displays. Cadmium damages the nervous system and is toxic in high doses.
