Multi F Outdoor Condenser Installation Manual
28
MULTI F / MULTI F MAX Outdoor Unit Installation Manual
Due to our policy of continuous product innovation, some specifications may change without notification.
©LG Electronics U.S.A., Inc., Englewood Cliffs, NJ. All rights reserved. “LG” is a registered trademark of LG Corp.
MULTI
F
MAX
MULTI
F
Selecting the Best Location for the Indoor Units
Select a location for installing the indoor units that will meet the following conditions:
• Within allowable parameters for proper connection to the outdoor unit (and branch distribution unit, if a Multi F MAX system).
• So that condensation drainage can be conveniently routed away.
• Include enough space around the indoor unit so that it is accessible for maintenance and service purposes.
• Where electrical noise / electromagnetic waves will not affect indoor unit operation. Maintain proper distances between the indoor units and
electric wires, audio and visual appliances, breaker / circuit panels, etc. If the frequency signal of the appliance is unstable, then install the
indoor unit a minimum of ten (10) feet away, and run the power and transmission cables through a conduit.
• An area that is level and with enough strength to bear the weight of the indoor unit(s).
Do Not’s
• ,QVWDOOLQDQDUHDZLWKREVWDFOHVWRDLUFLUFXODWLRQDURXQGWKHXQLWNHHSSURSHUGLVWDQFHVIURPFHLOLQJVGRRUZD\VIORRUZDOOVHWF
• Install in an area where operation sound will disturb occupants.
• ,QVWDOOLQDQDUHDWKDWH[SRVHVWKHLQGRRUXQLWVWRKHDWZDWHUVWHDPRLOVSODWWHULQJRUVSUD\
Selecting the Best Location for the Branch Distribution (BD) Units
%UDQFKGLVWULEXWLRQ%'XQLWVDUHXVHGRQO\ZLWK0XOWL
F MAX systems to distribute the refrigerant from the
RXWGRRUXQLWXSWRHLJKWLQGRRUXQLWV
Select a location indoors that will meet the following
conditions:
• Within allowable parameters for proper connection
to the Multi F MAX outdoor unit and indoor unit(s);
refrigerant piping and wire lengths must not exceed
amounts specified by LG Electronics, U.S.A., Inc.
• Condensate drain piping is not required.
• Ensure there is enough space in the installation
area for service purposes (minimum 24 inches);
install the refrigerant piping and electrical wiring
system in an easily accessible location.
• Level where there is enough strength to bear the weight of the branch distribution unit.
Do Not’s
• ,QVWDOOWKHEUDQFKGLVWULEXWLRQXQLWLQDORFDWLRQZKHUHLWZRXOGEHVXEMHFWHGWRVWURQJUDGLDWLRQKHDWIURPKHDWVRXUFHV
• ,QVWDOOLQDQLQVWDOODWLRQHQYLURQPHQWZKHUHWKHEUDQFKGLVWULEXWLRQXQLWZRXOGEHH[SRVHGWRKHDWZDWHUVWHDPRLOVSODWWHULQJRUVSUD\
• Install the unit in a location where any sound it generates will disturb occupants in the surrounding rooms.
• ,QVWDOOLQDORFDWLRQZKHUHWKHUHDUHREVWDFOHVWRDLUFLUFXODWLRQDURXQGWKHXQLWNHHSSURSHUGLVWDQFHVIURPFHLOLQJVGRRUZD\VÀRRUZDOOVHWF
• Install in an area where high-frequency electrical noise / electromagnetic waves will affect operation. Maintain proper distances between the
EUDQFKGLVWULEXWLRQXQLWVDQGHOHFWULFZLUHVDXGLRDQGYLVXDODSSOLDQFHVEUHDNHUFLUFXLWSDQHOVHWF
,QGRRUXQLWV,'8VPXVWQRWEHSODFHGLQDQHQYLURQPHQWZKHUHWKH,'8VZLOOEHH[SRVHGWRKDUPIXOYRODWLOHRUJDQLFFRPSRXQGV92&VRULQ
environments where there is improper air make up or supply or inadequate ventilation. If there are concerns about VOCs in the environment where
WKH,'8VDUHLQVWDOOHGSURSHUDLUPDNHXSRUVXSSO\DQGRUDGHTXDWHYHQWLODWLRQPXVWEHSURYLGHG$GGLWLRQDOO\LQEXLOGLQJVZKHUH,'8VZLOOEH
exposed to VOCs consider a factory-applied epoxy coating to the fan coils for each IDU.
)RUGHWDLOHGSODFHPHQWFRQVLGHUDWLRQVDQGLQVWDOODWLRQUHTXLUHPHQWVIRULQGRRUXQLWVUHIHUWRLWV,QGRRU8QLW(QJLQHHULQJDQG
or Installation Manuals.
PLACEMENT CONSIDERATIONS
6HOHFWLQJWKH%HVW/RFDWLRQIRUWKH,QGRRU8QLWV
%UDQFK'LVWULEXWLRQ8QLWV
PCB
1-31/321-3/16
4-3/8
Service Direction
Piping to
Indoor Units
Service Direction
Figure 12: %UDQFK'LVWULEXWLRQ8QLW.H\&RPSRQHQWV