LAC7750R_JA6GLLB ENGLISH CAR CD/MP3/WMA Receiver OWNER’S MANUAL MODEL : LAC7750R Please read this instruction booklet carefully and completely before installing, operating or adjusting this product. GERMAN Auto-CD-/MP3-/WMA-Receiver BEDIENUNGSANLEITUNG MODELL : LAC7750R Lesen Sie vor Anschluss, Bedienung und Einstellung dieses Gerätes die Anleitungen bitte sorgfältig und vollständig durch.
ENGLISH Safety note CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT SPLIT COVER(OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with the arrowhead symbol, within an equilateral triangle is intended to alert the user about the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock.
• A defective or soiled disc inserted into unit can cause sound to drop out during playback. • Handle the disc by holding its inner and outer edges. • Do not touch the surface of the unlabeled side of the disc. Do not stick paper or tape etc. on the surface. Do not expose the disc to direct sunlight or excessive heat. This unit cannot play 8cm disc (use 12cm disc only). 8 cm • Clean the disc before playback. Wipe the disc from the center outward with a cleaning cloth.
MP3/WMA Disc compatibility with this unit is limited as follows: 1. 2. 3. 4. Sampling Frequency / 8 - 48kHz (MP3) 22.05 - 48kHz (WMA) Bit rate / within 8 - 320kbps (include VBR) (MP3) 32 -320kbps (WMA) CD-R/CD-RW file system should be “ISO 9660” If you record MP3/WMA files using software which cannot create a FILE SYSTEM, for example “Direct-CD” etc., it will not be possible to playback MP3/WMA files. We recommend that you use “Easy-CD Creator” which creates an ISO9660 file system.
Before use Detaching the control panel You can detach the control panel when leaving the car. When detaching or attaching the control panel, be careful not to damage the connectors on the back of the control panel and on the panel holder. 1. 2. 3. 4. Press the “ ” button to unlock the control panel. Push the control panel to right. Pull the control panel out of the unit. Put the detached control panel into the protective case.
Control panel 1 2 17 3 4 5 16 1 [SOURCE] i 2 • Skip / Search I/i 8 Release/Eject WMA MP3 WMA Remote Sensor • Volume [VOL.
Battery Installation 1 2 3 Remove the battery holder with a sharp product like a ball point pen. Install the battery on the battery holder. Install the battery holder back into its original position. Note • Use only one CR2025 (3V) lithium battery. • Remove the battery if the remote control is not used for a long period of time. • Do not leave the product in a hot or humid place. • Do not handle the battery with metallic tools. • Do not store the battery with metallic materials.
Connection diagram Before connecting, make sure that the ignition switch is set to OFF, and remove the battery # terminal to avoid short circuits.
A From antenna B To the wiring of the vehicle colors of leads. • BLACK: This lead is for the ground connection. • ORANGE: This lead is for the phone line connection. • PINK: This lead is for the dimmer line connection. • RED: This lead is for connection to the power supply terminal when the ignition switch is set to ACC. • YELLOW: This lead is for connection to the battery (back-up) terminal from which power is always supplied. • BLUE: This lead is for the power antenna connection.
Basic operation Turning the unit on Press MUTE/PWR (POWER/ on the remote control) or any other button. Note When you insert the CD in the CD slot, the unit turns on. Turning the unit off Press and hold MUTE/PWR and then press and hold MUTE/PWR one more time(POWER/ on the remote control). Note When the demo function is “off”, press and hold MUTE/PWR. Insert a disc 1 2 Press to open the control panel. Draws the disc, and starts playback automatically. Eject a disc Press to open the control panel.
RDS AF(Alternative frequency) When the reception quality drops, the tuner automatically changes to another station in the network, broadcasting a better reception quality, using the PI and AF codes. ON : wherever you drive, you can continue to listen to the same program without interruptions. OFF : Only station name will be displayed. In case of poor reception no alternative station can be used.
DEMO OFF Demo is not displayed on screen. AUX In It is possible to use auxiliary equipment with this unit. Activate the auxiliary setting when using auxiliary equipment connected to this unit. • Enable : When using a auxiliary equipment. • Disable : When not using a auxiliary equipment. AUX In Att. (Auxiliary In Attenuate) You can adjust the volume level of each source to prevent radical changes in volume when switching between sources.
Adjusting the sound level 1 2 Press SEL (SEL on the remote control) repeatedly to select the mode you want to adjust from volume, bass, middle, treble, balance and fader. The indicator lights up in the following order. VOLUME(VOL) t EQ - USER(BAS, MID, TRB) t BALANCE(BAL) t FADER(FAD) Rotate the MUTE/PWR. (Press VOLUME on the remote control) to adjust the sound quality. Indication Turn right Turn left VOL BAS Increase the volume level. Decrease the volume level. Increase the bass level.
Pairing your unit and Bluetooth phone Pairing links your unit and Bluetooth phone, and is required only once for the initial setup. Before you start the pairing procedure, make sure the Bluetooth feature is turned on in to your Bluetooth phone. Refer to your Bluetooth phone’s user guide. 1 Press B/T to connect your Bluetooth phone. The “Connect” is displayed. If connecting through a Bluetooth phone, the handsfree connection or headset connection may operate depending on the type of phone.
Missed call notification When an incoming call is not answered, the missed call message is displayed on the your screen. 1 The “ ” appears on the screen. 2 Press B/T to place a call. 3 Press i (M M? on remote control) to enter the “Received Call”. 4 To end the call and hang up the phone, press B/T button. This function is adjust only on hands free mode. Audio transfer It is possible to select the automatic connection between your Bluetooth phone and this unit. 1 Press B/T to answer the call.
Disconnecting a Bluetooth phone It is possible to disconnect your Bluetooth phone from this unit. 1 Press B/T and then press U/AS or u/PS to select the “Disconnect”. 2 Press i. The “YES” and “NO” appears on the screen. 3 Press B/T to disconnect a Bluetooth phone from the unit. The “DISCONNECTED” appears on the screen. Making a call from the preset list It is possible to make a call from the preset phone number list. 1 Press B/T and then press U/AS or u/PS to select the “Preset”.
Search(as preset) stored a call number It is possible to store in preset number from the stored phone number list. 1 2 3 4 5 Refer to the step 1 - 4 of “Search stored a call number” on page 16. Press i and then press U/AS or u/PS to select the “To preset”. Press i to storing in preset number. Press U/AS or u/PS up or down to store in desire preset number(1 - 6). After select desire preset number, press B/T. The “SAVED” appears on the screen.
Note • When you want to make an international call, press i to add “+”. press I to delete ” +”. • “+” can only be added when the detail list of Missed call, Dialed call or Received call is selected. Pairing your unit and Bluetooth device (MP3 Player, MP3 Phone...) When you activate your Bluetooth device’s linked unit, you can listen to MP3 with wireless connections. The method of use for a Bluetooth device is the same as when using a Bluetooth phone. (Refer to the page 14 for details.
AVRCP Based on the GAP Profile, this uses a Controller (CT) - PDA, computer mobile phone etc., which sends a command to a Target (TG) - TV, discman, headphone etc. The command can be to Play, record, colour control, volume control etc., depending on the nature of the devices involved and the scenario. The commands are transported by a new additional protocol, called the Audio/Video Control Transport Protocol (AVCTP).
RDS operation RDS Display options In normal RDS operation the display will indicate the station name.
To directly play a file, press NUMBER (#) on remote control and then press the track number with 0-9 number. Pause CD MP3 WMA 1 Press B/X during playback. 2 To return to playback, press B/X again. Skip to next track/file CD MP3 WMA Press briefly i (M M? on the remote control) to select the next track or file. Skip to previous track/file CD MP3 WMA Press briefly I (?m m on the remote control) within 3 seconds of playing time.
CD TEXT / ID3 TAG CD MP3 WMA When playing a disc containing information, you can see the CD TEXT/ID3 TAG information. In CD TEXT, information about the disc (disc title, performer and track title) is recorded. In a ID3 TAG, information about the file (album title, Performer name, song title) is recorded. In a WMA Content, information about the file (song title, Performer name) is recorded. If there is no information, “NO TEXT” will be shown in the display window.
Troubleshooting Sy Co : Symptom / : Correction Ca : Cause Ca The loaded disc is of a type this unit cannot play. Co Check what type the disc. Sy Power doesn’t turn on. / The unit doesn’t operate. Ca Leads and connectors are not properly connected. Co Confirm once more that all connections are correct. Ca The fuse is blown. Co Rectify the problem that caused the fuse to blow, and then replace it. Be very sure to install the correct fuse with the same rate.
AUX SECTION Frequency Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Hz-20 kHz S/N Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80 dB Distortion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.05 % Channel Separation (1kHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
