Engineering Manual

STD. WALL-MOUNTED | 49
Standard Wall-Mounted
Due to our policy of continuous product innovation, some specications may change without notication.
©LG Electronics U.S.A., Inc., Englewood Cliffs, NJ. All rights reserved. “LG” is a registered trademark of LG Corp.
MULTI
F
MAX
MULTI
F
STANDARD WALL-MOUNTED INDOOR UNITS
Mechanical Specications and Features
Standard Wall-Mounted Indoor Units
General
All LG indoor units are factory assembled, wired, piped, and pro-
vided with a control circuit board, fan, and motor. Standard Wall-
Mounted units have a sound rating no higher than 46 dB(A) as tested
per KSA0701 ISO Standard 3745.
Coil
Indoor unit coils are comprised of a minimum of two rows of
aluminum fins mechanically bonded to copper tubing. The coils are
pressure tested at the factory. Each unit is provided with a factory
installed condensate drain pan below the coil.
Refrigerant System
The system is designed for use with R410A refrigerant. The refrig-
eration circuit is pressure-tested at the factory and shipped with a
holding charge of helium gas. Refrigerant pipe connections are 45°
flare. All refrigerant lines from the outdoor unit to the indoor units
must be field insulated.
Electrical
The indoor units require 208–230Vac/60Hz/1Φ power with voltage
variance of no more than ±10%.
Casing
The units mount on a vertical surface. They are shipped with a sepa-
rate back plate that secures the unit to the wall, protruding no more
than nine (9) inches. Refrigerant piping can be installed in one (1) of
four (4) different directions.
Finish
The Standard Wall-Mounted unit has a curved architectural panel
with a pearl white finish. Unit casing has a pearl white or dark gray
finish and is manufactured of heavy-duty acrylonitrile butadiene
styrene (ABS) and high impact polystyrene (HIPS) plastic.
Fan Assembly and Control
The unit has a single, direct-drive, crossow fan made of high strength
ABS plastic. The fan motor is brushless digitally controlled (BLDC)
with permanently lubricated and sealed ball bearings. The fan / motor
assembly is mounted on vibration attenuating rubber grommets. Fan
speed is controlled using a microprocessor-based direct digitally
controlled algorithm that provides pre-programmed, eld-selectable
xed or auto fan speeds in the Heating and Cooling modes. For
Standard Wall-Mounted units, the indoor fan has Low, Med, High, Jet
Cool, and Auto settings for Cooling mode; and has Low, Med, High,
Jet Heat, and Auto settings for Heating mode. The Auto setting adjusts
the fan speed based on the difference between the controller setpoint
and space temperature. Also, the separate Chaos setting provides a
simultaneous and random change in fan speed and ow direction at
the discharge, simulating a natural outdoor breeze.
Air Filter
The return air inlet has a factory-supplied primary removable, wash-
able filter. The unit is also equipped with a secondary 3M Micro Dust
filter. Filters are accessed from the front of the unit without the use
of tools.
Airflow Guide Vanes
A factory-installed motorized guide vane controls the direction of
airflow from side to side. A motorized louver provides an automatic
change in airflow by directing the air up and down for uniform air
distribution.
Microprocessor Control
The indoor unit has an integrated control panel to communicate with
the outdoor unit. All unit operation parameters are stored in non-vola-
tile memory resident on the unit microprocessor. The microprocessor
controls space temperature through using the value provided by the
temperature sensor within the indoor unit. The microprocessor control
will activate indoor unit operation when the indoor room temperature
falls below or rises above a setpoint temperature, at which point, a
signal is sent to the outdoor unit to begin the appropriate mode. The
microprocessor also provides self-diagnostics and auto restart func-
tions. A eld-supplied four-wire power / communications cable must
be installed to connect the indoor unit(s) to the outdoor unit.
Controls
The indoor unit casing has a factory-standard, integral infrared sen-
sor to communicate with the supplied LG wireless handheld remote
controller. An optional LG supplied wired controller is available as
an additional accessory. Communication between the indoor units
and the outdoor unit is accomplished through 18 AWG, four-core,
stranded and shielded power / communication cable. The indoor unit
has built-in wi-fi and can be controlled with LG’s SmartThinQ app on
a smart device. A field-supplied wi-fi network and smart device are
required. The SmartThinQ app is free and is available for Android
and iOS smart devices.
Condensate
The unit is designed for gravity draining of condensate and includes
a flexible drain hose capable of installation in one of two directions.
The unit also includes a connection that is compatible with the Aqua-
Guard
®
AG-9300-LG condensate sensor.
• Inverter (Variable speed fan)
• Comfort Air
• 3M filter
• Jet cool/Jet Heat
• Group control
• Self-cleaning indoor coil
• Auto operation
• Auto restart operation
• Built-in wi-fi
• Dehumidifying function
• Self-diagnostic function
• Wireless LCD remote control included
Features
Figure 60: Multi F Standard Wall-Mounted Indoor Unit.