OWNER'S MANUAL IR Dome Camera Please read this manual carefully before operating your set and retain it for future reference.
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
• • Caution: Danger of explosion if battery is incorrectly replaced. Replaced only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions. Caution: This installation should be made by a qualified service person and should conform to all local codes. Holes in metal, through which insulated wires pass, shall have smooth well rounded surfaces or shall be provided with brushings.
LG Electronics hereby declares that this/these product(s) is/are in compliance with the essential requirements and other relevant provisions of Directive 2004/108/EC and 2011/65/EU. European Standards Centre: Krijgsman 1, 1186 DM Amstelveen The Netherlands Disposal of your old appliance 4 1. All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities. 2.
Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
Cautions for Safe Operation Power Supply Operating and storage location This camera must always be operated DC 12 V or AC 24 V.Certified/Listed Adaptor which comply with LPS. Avoid viewing a very bright object (such as light fittings) during an extended period. Avoid operating or storing the unit in the following locations. Handling of the unit Be careful not to spill water or other liquids on the unit. Be cautions not to get combustible or metallic material inside the body.
Contents Features ............................................................................. 8 Privacy Mask Setting .............................................................29 Accessories.................................................................................. 8 Special Menu Settings ..........................................................31 Part Names and Functions .................................................... 9 SYSTEM Setting ..................................................
Features This IR Bullet Camera is designed for installation in a video surveillance system. This manual contains instructions on how to install and manage the IR Bullet Camera in your video surveillance system. Should you require any technical assistance, please contact authorized service center. t High resolution and high sensitivity with a 6 mm (1/3 Type) CCD. t Day & Night function. t HSBLC/BLC covers various light conditions.
Part Names and Functions a Dome Cover b IR LED c IR Sensor a b c d e f d Focus lock lever Fixes the focus position after adjusting. e Zoom lock lever Fixes the zoom position after adjusting.
Part Names and Functions h Setup menu control buttons i Video Out connector Use this jack for checking the picture with portable monitor when install the camera. j Power input connector h i j k 10 Supplies AC 24 V or DC 12 V from an external power source.
Connections Basic connection The peripheral devices (DVR, monitor, etc.), AC/DC adapter and cables are not supplied. 1. Make the video signal connection between the camera and the monitor or DVR. 2. Connect a external power source to the power input jack of the camera. (recommended power adapter is AC 24 V/0.5 A, DC 12 V/0.
Installation 2. Mounting the Camera Pass the connection cable through the inner side of the ceiling. Note: SELFTAPPING SCREW 4 Place FRONT MEZ62687703 PRODUCT CENTER POSITION POSITION CABLE HOLE (LCV5300) CABLE HOLE (LCD5300) PRODUCT CENTER CABLE HOLE (LCV5300) CABLE HOLE (LCD5300) SELFTAPPING SCREW 4 Place FRONT MEZ62687703 SELFTAPPING SCREW 4 Place FRONT MEZ62687703 12 POSITION Follow the instructions below to surface mount the camera with supplied camera mounting bracket. 1.
Installation 3. Install the camera mounting bracket to the ceiling. 4. Connect the cables to the cable jacks of the camera body.
Installation 5. 14 Assemble the camera and the housing. Make sure when you assemble the camera in the right direction. And then, assemble the dome cover and lens cover. 6.
Installation Image Adjustment 2. Connect a portable monitor to the video jack. You can manually adjust the pan/tilt/azimuth angles, focus, and zoom while observing the connected monitor. Notes: t Do not hold the camera by lens unit to adjust panning, tilting, or azimuth. t The video output to the BNC will be interrupted while a portable monitor is connected to the video jack. 1. Use the supplied wrench to loosen the screws and remove the dome cover Remove the Dome cover and lans cover.
Installation 3. Adjust the pan/tilt/rotate position of the camera. 4. Adjust the zoom. 4-1. Unlock the zoom lever. 4-2. Move the lever to adjust the zoom. 4-3. Lock the lever. TILT TILT TELE ROTATE WIDE PAN Note: Disassemble the IR cover as illustrated in case of difficult occasion to adjust the zoom lever.
Installation 5. Adjust the focus. 6. 5-1. Unlock the focus lever. 5-2. Move the lever to adjust the focus. This camera utilizes an on-screen user MENU. To set items on the menu, use the following buttons. After then attach the lens cover and dome cover. 5-3. Lock the lever. FAR NEAR Note: Disassemble the IR cover as illustrated in case of difficult occasion to adjust the focus lever.
Menu Operation t UP button: Used to move upper direction on the menu screen. Use this button to select an item or adjust the parameters. t DOWN button: Used to move lower direction on the menu screen. Use this button to select an item or adjust the parameters. t RIGHT button: Moves the cursor to the right. Used to increment the value selected in the menu. The parameter changes each time this button is pressed. DOWN LEFT SET t RIGHT LEFT button: Moves the cursor to the left.
Menu Operation OSD Menu Overview The following table shows the list of menu items and options. You can adapt the camera to your requirements by setting up the respective items in these menus. Main Menu Sub Menu ALC /ELC SHUTTER OFF / AUTO EXIT RET/ TOP / END - AWC / SET KET MANUAL EXIT RED BLUE SMART IR x512, ..., x2, AUTO, OFF, A.FLK, 1/160, ...
Menu Operation MOTION ON DET 3D-DNR 0 to 100 OFF EXIT MASK SELECTION DISPLAY RECTANGLE PRIVACY MASK ON POSITION ,/ POSITION ;. SIZE ,/ SIZE ;. MASK SELECTION DISPLAY CIRCLE 20 MASK SELECTION RET/ TOP / END POSITION ,/ POSITION ;. SIZE ,/ SIZE ;. RADIUS 1 to 2 OFF /MOSAIC / ON POLYGON PRIVACY COLOR1 to COLOR8 MASK SHAPE POSITION RET/ TOP / END EXIT OFF ZOOM x 1.0 to x 16.
Menu Operation SYSTEM EXIT FACTORY RESET EXIT RET/ TOP / END RET/ TOP / END General Operation 1. Press [SET] button. The Main OSD menu screen appears on the monitor. 2. Use [UP] or [DOWN] button to select an option then press [SET] button. Submenu appears on the monitor. 3. Use [UP] or [DOWN] button to select a submenu option. 4. Use [LEFT] or [RIGHT] button to select a value. 5. Select [EXIT] option then press [SET] to exit the setup menu.
Menu Operation previous setup menu. Backlight setting t Use Backlight option to view the object clearly in backlight conditions. RETURN: Return to the previous. Exposure Settings You can set the exposure options using the EXPOSURE menu. 1. Select [EXPOSURE] option on the [CAMERA SETTING] menu. 2. Use [LEFT] or [RIGHT] button to select a mode. 3. Press [SET] button and the EXPOSURE menu appears. 1. Select [Backlight] option. 2. Use [LEFT] or [RIGHT] button to select a mode then press [SET].
Menu Operation t HSBLC: Use for masking brightness of the specific area to view the subject more clearly. The HSBLC mode is automatically activated only in low luminance scene. > t AREA SETTING: Use [LEFT] or [RIGHT] button to select a area then use [UP] or [DOWN] button to select a [ON] or [OFF]. Press [SET] to exit the Area setting menu. > GRAY SCALE: Use [LEFT] or [RIGHT] button to select a gray scale. (GRAY, D.GRAY, BLACK) > USER SCALE: Use [LEFT] or [RIGHT] button to select a bright level.
Menu Operation AGC (Automatic Gain Control) setting If the images are too dark, change the maximum [AGC] value to make the images brighter. But noise is increase. 1. Select [SHUTTER] option. 2. Use [LEFT] or [RIGHT] button to set shutter speed. Notes: 1. Select [AGC] option. 2. Use [LEFT] or [RIGHT] button to select a mode. SHUTTER (Shutter Speed) setting Select the desired shutter speed for camera exposure.
Menu Operation SENS-UP setting Note: If pictures are not clear due to darkness, this SENS-UP operation would increase the sensitivity of picture. If you set to one of the SHUTTER options except AUTO and OFF on the [SHUTTER] menu, the [SENS-UP] setting is not available and [---] mark is displayed. White Balance settings Select the method by which the camera shifts its output colors to compensate for the color of a light source. 1. Use [UP] or [DOWN] button to select [SENS-UP] option. 2.
Menu Operation button. t Day/Night Setting MANUAL: You can set the white balance options manually. > t t RED: Obtains the optimum amount of red gain. > BLUE: Obtains the optimum amount of blue gain. AWC/SET KEY: If you select the AWC/SET KEY mode, you will be able to set up the White Balance automatically using [SET] button. AUTO : Use [LEFT] or [RIGHT] button to select the AUTO then press [SET] button. 1. Select [DAY/NIGHT] option. 2.
Menu Operation > LEVEL: Use [LEFT] or [RIGHT] button to select a level. > t DWELL TIME: Use [LEFT] or [RIGHT] button to select a dwell time. DAY: Color mode enabled. t NIGHT: Black-and-white mode enabled. > SmartIR Setting SmartIR function improve the sensitivity in the low luminance. SmartIR analyze the image of the screen, when the subject is close. Then SmartIR reduce the IR LED brightness and gain to prevent saturation of the closed subject.
Menu Operation t t SIZE ,/ : Enlarge or decrease the horizontal size of the prevent saturation zone. 3. SIZE ;. : Enlarge or decrease the vertical size of the prevent saturation zone. Motion Detection Setting The motion detection detects the moving objects in the scene by monitoring changes in brightness level. You can select the level of sensitivity for motion detection to 8 zone. 5. Select [MOTION DET] option. 2. Use [LEFT] or [RIGHT] button to select a [ON] and press [SET].
Menu Operation 3D-DNR Setting Privacy Mask Setting This function is aiming at the protection of personal privacy, selecting a screen part black not to be displayed in the screen. Up to 8 zones can be registered. 1. Select [3D-DNR] option. If pictures are not clear due to brightness, this option would reduce the noise of picture. 2. Use [LEFT] or [RIGHT] button to select a value. 1. Select [PRIVACY] option. 2. Use [LEFT] or [RIGHT] button to select a [ON] and press [SET].
Menu Operation t OFF, MOSAIC, COLOR 1 to COLOR 8 on the DISPLAY option. > Use [UP] or [DOWN] to select an option then use [LEFT] or [RIGHT] button to adjust the option. POSITION,/: Moves horizontal position of the mask. POSITION ;.: Moves vertical position of the mask. SIZE ,/: Enlarge or decrease the horizontal size of the mask. SIZE ;.: Enlarge or decrease the vertical size of the mask. CIRCLE : > > > 30 Use [LEFT] or [RIGHT] button to select a mask (MASK1 to MASK4) on the [MASK SELECTION].
Menu Operation [SET] button to move the polygon on the [POSITION]. Note: You can adjust the mask color manually except for color 8. Special Menu Settings This menu lets you adjust and set up D-ZOOM, D-EFFECT, SHARPNESS, COLOR, SYNC, USER TITLE, LANGUAGE function by yourself in the SPECIAL menu. 1. Select [SPECIAL] option. 2. Press [SET] button and the SPECIAL menu appears.
Menu Operation t D-ZOOM (Digital Zoom ) Setting You can select the digital zoom level. TILT: Use [LEFT] or [RIGHT] button to move the screen. Note: If you set the [D-ZOOM] to ON, the ZOOM level is set to [x1.0] automatically. D-EFFECT (Digital effect) Setting You can select the digital effect. 1. Select [D-ZOOM] option on the [SPECIAL] menu. 2. Use [LEFT] or [RIGHT] button to select a [ON] then press [SET] the DIGITAL ZOOM menu appears. When you set to ON, the displayed image can be shaking. 3.
Menu Operation t MIRROR: Turn on the mirror effect. COLOR Setting t OFF: Turn off the digital effect. You can switch the displayed picture to gray scale or color. SHARPNESS Setting The degree to which the boundary of the two portions is clearly distinguished. 1. Select [SHARPNESS] option on the [SPECIAL] menu. 2. Use [LEFT] or [RIGHT] button to change a adjust the option. If you set the sharpness value to higher, the image outline becomes sharp.
Menu Operation SYNC Setting USER TITLE Setting You can use the camera identification to assign a number and character to the camera. To disappear the user title, select [OFF]. 1. Select [SYNC] option on the [SPECIAL] menu. 2. The [SYNC] option is set to [INT] automatically. 1. Select [USER TITLE] option on the [SPECIAL] menu. 2. Use [LEFT] or [RIGHT] button to select a [ON] then press [SET]. The USER TITLE menu appears. A Note: AC24V Adaptor have to use for [LL] mode setting. 3.
Menu Operation t t A (Blank): Inserts a space at the cursor position. / SYSTEM Setting : Moves cursor to left or right. LANGUAGE Setting Select the viewer language for the camera setup menu and OSD information display. 1. Select the [SYSTEM] menu. 2. Press [SET] button and the SYSTEM menu appears. 3. Use [UP] or [DOWN] button to select the option. t 1. Select [LANGUAGE] option on the [SPECIAL] screen. 2. Press [LEFT] or [RIGHT] button to select a language. 4.
Specification Item LCV5300R-BN LCV5300R-BP Signal System NTSC PAL Image Device Total/Effective Pixels Number Horizontal Resolution 520 000 Pixels / 480 000 Pixels 610 000 Pixels / 570 000 Pixels 650 TV Lines (Color), 700 TV Lines (B/W) ISP XDI-V Lens 2.8 mm to 11 mm Vari-focal Lens, F1.2 Minimum Illumination (30 IRE) Color 0.03 lx (Sens-up Off, F1.2), 0.000 3 lx (Sens-up Auto, F1.2), 0.000 1 lx (Sens-up x512, F1.
Specification Item LCV5300R-BN LCV5300R-BP SmartIR IR Anti-Saturation BACKLIGHT BLC / HSBLC / OFF DNR 2D + 3D-DNR Exposure ALC /ELC Auto Gain Control OFF/ LOW/ MIDDLE/ HIGH Electronic Shutter Speed Digital Zoom 1/60 to 1/120 000 1/50 to 1/120 000 x16 Sens-up OFF / AUTO(x2, ...
Specification Item LCV5300R-BN LCV5300R-BP Operation Temperature/ Humidity -10 ºC to 50 ºC / 0 % RH to 80 % RH Storage Temperature/ Humidity -20 ºC to 60 ºC / 0 % RH to 85 % RH 38 Protection IP66 Dimension (Ø x H) 140 mm x 122 mm Weight 705 g
