OWNER’S MANUAL DIGITAL VIDEO RECORDER Before connecting, operating or adjusting this product, please read this owner’s manual carefully and completely. MODEL LE2104 Series LE2104D Series P/NO : MFL60560488 1106 (V2.
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Warning: Wiring methods shall be in accordance with the National Electric Code, ANSI/NFPA 70. Warning: This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
Disposal of your old appliance 1. When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC. 2. All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities. 3. The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health. 4.
Safety warnings and Cautions The following are warnings and cautions for the safety of the users and for the prevention of any property damage. Please read the following carefully. WARNING • Turn off the system before installation. Do not plug in several electric devices to the same outlet. -- • This may cause heating, fire, or electric shock. Do not place any liquid container on the system, such as water, coffee, or other beverage.
CAUTION Please beware of the following precautions before installing the DVR. • Avoid positioning the product in any place where the unit may come into contact with moisture, dust, or soot. • Avoid placing in direct sunlight or near heating appliances. • Keep the product away from electric sparks or magnetic substances. • Avoid temperature extremes (recommended operating temperature is between 0 °C - 40 °C). • Do not place any conductive material through the ventilation grills.
Contents Network Settings........................................................................31 System Settings...........................................................................35 Introduction....................................................................... 7 Recording......................................................................... 40 Features............................................................................................ 7 Instant recording......................
Introduction • Max five clients can access one DVR server simultaneously. • Network bandwidth throttle. -- Features Automatically adjust a bandwidth according to network speed status of unit. • Stable embedded Linux operating system. • Remote alarm notification via client software or E-mail. • Journal filing system for HDD file recovery following power recovery. • Time and date sync from NTP server. • Daylight saving mode. • Small file sizes with H.264 compression.
Front Panel LE2104D model a i j b c k d e l f g h m n LE2104 model a i j k a POWER Indicator: Lights when the DVR is powered. HDD Indicator: Blinks when the HDD is accessed. NET Indicator: Lights when a network cable is connected. b Disc Tray (LE2104D model only): Insert a disc here. c OPEN (LE2104D model only): Opens or closes the disc tray. d SETUP/ESC: Displays the setup menu or cancels operation on the setup menus. e Playback Control Buttons -- M: Pauses playback.
Rear Panel Rear panel with the TV or VGA output select switch. a b c j k l d e f m n op g h i g h i Rear panel without the TV or VGA output select switch. a b c j k l d e f m n op a VIDEO INPUT Connect the camera’s video output to these BNC connectors. h ALARM IN/OUT Terminals -- IN: Input terminals for alarm(relay) signal. -- OUT: Output terminals for alarm(relay) signal. b LOOP OUT The signal from VIDEO INPUT connector is looped out to this connector.
Remote Control • LOCK: Displays the lock menu to change user type or disable system operation. • OPEN: Opens or closes the disc tray. This button is only used for LE2104D models. • ID: Set the appropriate DVR system ID to operate via the IR Remote Controller when using the multiple DVR. Press the ID button then press the number button within 2 seconds to select the system ID of the DVR. If you set the system ID to “0”, you can control multiple DVR at the same time.
Connections and settings Precautions • Depending on the camera and other equipment there are various ways to connect the unit. Please refer to the camera manual or manuals for other devices as necessary for additional connection information. • Be sure to switch off the camera before installation and connection. Basic Connection Overview Connect the coaxial-type cameras Connect BNC type spot monitor. For audio amplifier Connect power code Connect network cable for client control.
Connecting Camera VGA Monitor connection Connect cameras to the unit using 75 Ω video coaxial cables with BNC connectors. There are two BNC connectors for each camera. Either connector can receive a camera’s signal. This signal is looped-through (directly connected) to the other connector, so that you can send the camera’s signal to other equipment. When using the VGA monitor, set the Video Output mode select switch to VGA position.
USB memory device LAN connection Insert the memory device into the USB port. The system automatically recognizes the device. Connect the LAN port to an available 10/100 base-T port with a straight ethernet cable (not supplied). The NET indicator on the front panel will be lit. Using a USB memory device the system software can be easily upgraded. USB backup device Connect the USB cable of the USB backup device to the USB port. (Example: HDD or other external storage.
Connecting LKD1000 controller Rear of the DVR Connecting the LKD1000 controller to control the DVR. (Refer to the manuals of the LKD1000 controller for more details.). Rear of the DVR TX- TX+ LKD1000 Controller Notes: • Do not connect a PTZ camera with LKD1000 controller to the D1 or D2 port. It may cause a malfunction. • The MAIN and SPOT buttons of the LKD1000 controller are not activated for LE2104/LE2104D models. Alarm sensor Terminal No.
HDD INSTALLATION Note for Hard Disk Drive The internal hard disk drive (HDD) is a fragile piece of equipment. Please follow the guidelines below when using the DVR to protect against possible HDD failure. We recommend that you back up your important recordings onto an external backup device in order to prevent accidental loss. Make sure that the power is turned OFF when attaching or removing the HDD. • Do not move the DVR while the power is on.
5. Attach the HDD onto the hard disk mounting brackets with four screws. Note: When you add the new HDD, do not change the position of the HDD. It may delete the current data and cause a malfunction. Replacing the Hard Disk Drive Turn the power of the unit off and detach the power plug from the outlet. 1. Follow steps 1-4 described in “Installing the Hard Disk Drive”. 2. Remove the connector from the HDD. 6. Attach the hard disk mounting brackets with the screws. 7. Connect the HDD power cable.
Recommended HDD The following HDD has been tested and compatibility is ensured. When you attach multiple HDDs use the recommended HDDs. Note: If you do not use the recommended HDD, the system may not be operated normally. Maker Seagate Hitachi RPM Capacity Interface • This DVR is based on a VGA monitor using OSD. We recommend to using the VGA monitor with this unit. If you use a composite monitor, the OSD quality may lower to read it. • User access rights User Level View Model No.
General Explanation of the Live Screen on the Main Monitor Displays the PTZ remote control window. Main Monitor Screen ab cd Displays the search menu. e f Displays in the full screen display mode to return to the 4 division screen windows. Views the all channels in sequence on the full screen display mode. You cannot use sequence mode with the 4 split. Note: The covert channel(s) or video loss channel(s) is(are) not displayed with power and normal user.
PTZ Camera Control You can control the cameras connected via the data port of RS-485 terminal. You must set the configuration between the PTZ camera and the DVR. e To manually adjust the iris of a camera. f Displays the Selected Preset Number g Number Buttons To input the preset number. h To register preset positions. i To move the camera to the preset position. j To delete a memorized preset position. k To start a preset tour. l To displays the setup menu of the PTZ camera. 1.
2. Use number buttons to enter the memorized preset position’s index number then press ENTER or click the icon. The camera moves to the preset position and the picture of the camera in that position appears on the monitor. To Clear the Preset Position You can clear a memorized preset position. 1. Press the CLEAR button or Click the icon. 2. Use number buttons to enter the memorized preset index number then press ENTER or Click the clear the preset positions.
14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 Normal User Login (Local) Normal User Logout (Local) Configuration Changed Configuration Imported Factory Default Set Backup Started Backup Finished Backup Failed Export Started Export Finished Export Failed S/W Updated HDD Added (HDD1) HDD Added (HDD2) HDD Removed (HDD1) HDD Removed (HDD2) HDD Formatted (HDD1) HDD Formatted (HDD2) HDD Changed (HDD1) HDD Changed (HDD2) HDD Damaged (HDD1) HDD Damaged (HDD2) Notes: • You can also use the COP
Configuration menu Using a mouse to set a menu The features and options of the DVR are configured through the menu. The operations of this unit can be set via a menu displayed on the main monitor. You can select and set the operational conditions by using the buttons on the front panel and the remote control or using a Mouse connected to the unit. Use the left or right mouse buttons to set the menu. Only administrator-level users have permission to access the Setup menu and configure the DVR.
Notes: Camera • When you operate the function menu by using the remote control and front panel buttons, both buttons are operated in the same way to control the function menu. The channel name, covert and input audio channel settings are configured. • All the operation explanations are based on using the remote control. Camera settings • Channel: Selects the desired channel to set the options. • Name: Enter the channel name using up to 12 characters.
PTZ Recording Settings for the PTZ cameras connected via the data port of the RS-485 terminal. Settings concerning normal recording. • Channel: Selects the desired channel to set the connected PTZ camera. • Port: Selects the connected data port of the RS-485 terminal on the rear panel. The D2 (DATA 2) port is used to control the PTZ camera connected to DVR or to control by using the LKD1000 controller.
Sensor Recording Motion Recording Settings concerning sensor recording. Settings concerning motion recording. • Channel: Selects the desired channel to set the options. • Channel: Selects the desired channel to set the options. • Resolution: Selects the recording resolution. • Resolution: Selects the recording resolution. • Quality: Selects the recording picture quality (LOWEST, LOW, STANDARD, HIGH or HIGHEST).
Video Format Selects the video format to NTSC or PAL according to your video system format. 6. Select [OK] icon and press ENTER to confirm your settings. 7. Select [Exit] and press ENTER to exit the sub-setup menu. Note: This function is not activated for spot out channel. Schedule settings The DVR can record according to a schedule set by the user. It can also record manually regardless of date and time. The recording can be made either continuously or triggered by events (alarm and motion detection).
To Set the Recording Schedule for a Typical Day of the Week -- Green+Red (Continuous+Sensor event recording): Recording starts automatically from the preset time. When the sensor alarm occurs within a designated time, change the continuous recording mode to sensor event recording mode and recording starts automatically. -- Green+Blue (Continuous+Motion event recording): Recording starts automatically from the preset time.
3. Select a special day title on the list and press ENTER. The title color turns red. 4. Select the [Edit] icon then press ENTER to edit the special day or select the [Delete] icon to delete the special day schedule. 5. Press SETUP/ESC to exit the special day schedule list. Note: If the special day recording schedule is duplicated with the other recordings, only the special day recording is possible. Copying the Recording Schedule Copying from the Scheduled Data of the Channel 3.
Display settings Main Monitor • Dwell Time: You can set the channel sequence time to 2 SEC, 5 SEC, 10 SEC, 20 SEC, 30 SEC, 40 SEC, 50 SEC, 60 SEC, 70 SEC, 80 SEC or 90 SEC. Spot Monitor OSD • Language: Select a language for the setup menu and information display. • Channel Name • -- ON: Displays the title of the channel. -- OFF: Displays the live picture without the title of the channel.
Event Settings Motion • Channel: Select the channel to set motion detection. • Sensitivity: Set the level of sensitivity for the created motion detection area. Sensitivity can be set from level 01 to 10 or NONE. • Relay Output: -- ON: Outputs the alarm (relay) signal via the ALARMOUT terminal. -- OFF: Not used. Notes: Sensor • In the condition that illumination is low and the outline of object is not clear enough to see, regardless of sensitivity, Motion Event could be possible not to happen.
5. Click the right mouse button to exit the settings. 6. Select [Exit] and press ENTER to exit the sub-setup menu. Network Settings Output • • Relay Off -- ALARM ACK.: Use the ALM.OFF button to stop alarm. -- POST-ALARM TIME: The alarm is stopped after postalarm time. System Alarm Out: -- ON: Outputs the alarm (relay) signal via the ALARM-OUT terminal below cases. >> When the HDD has bad sector.
• IP Address: Enter an IP address using the virtual keyboard. • Subnet Mask: Enter a subnet mask address using the virtual keyboard. • Gateway: Enter the gateway address using the virtual keyboard. • Primary DNS: Enter the Main DNS server address using the virtual keyboard. • Secondary DNS: Enter the Sub DNS server address using the virtual keyboard. • TCP/IP Port: Enter the TCP/IP Port number using the virtual keyboard.
When you want to change DDNS host name Notification If you want to change the registered host name to new one, follow as shown below. 1. Enter a new host name in [Host Name] option. 2. Select the [Update] icon and press ENTER. The confirmation window will be displayed to change your host name. • • 3. Select the [OK] and press ENTER. When host name is properly changed, the changed host name will be displayed in [Registered Host]. • Sensor On: -- ON: Sends an e-mail when a sensor has occurred.
Mail • • • Emergency Notification -- ON: Notifies the user of unit operating information by e-mail according to notification settings. -- OFF: The notification function is not used. The mail options are not set. SMTP Server: Enter the SMTP Server address using the virtual keyboard. If notification is set to ON and the SMTP server option is empty, the SMTP Port, User Name, Password and TLS options are not set. SMTP Port: Enter the SMTP Port Number using the virtual keyboard.
System Settings • Daylight Saving End: Select the Daylight Saving end time. Caution: If you change the time setup, warning message will be displayed. For example, if you delay the time by 10 minutes, the overlapped 10minutes data can be deleted. NTP • NTP: Set to ON when using the NTP (Network Time Protocol) server for time adjustment. If the NTP is set to OFF, the time settings should be entered manually and the [Server], [Private Time Server], [Sync. Interval] and [NTP Test] options are not set.
Buzzer User You can register a new user with various access rights to the DVR or client program. • • • • Button -- ON: Makes a sound when using the buttons. -- OFF: Turns off the button beep. Sensor -- ON: Makes a sound when a sensor occurs. -- OFF: Turns off the sensor buzzer. Motion -- ON: Makes a sound when a motion is detected. -- OFF: Turns off the motion buzzer. • Number: Select the number to add new user ID or change the user ID, user level or password.
Update Hard Disk The update feature allows you to upgrade DVR software and add/upgrade PTZ protocols. In this case, the current DVR settings are not deleted or replaced during the update process. • Format: Initializes the HDD (Hard Disk Drive). All data on the selected HDD will be erased. How to format the HDD 1. Select the [Event Partition] option and set the event partition rate of the HDD. If you set the event partition to 60 %, the remaining space of 40 % is set to normal partition automatically.
Note: If you change the value of event partition, the current recorded data of HDD is deleted and the partition is reset. The partitions will be formatted automatically and the system will be restarted. Backup • You cannot use the [Estimate], [Start] and [Erase] options in backup progressing. • Do not remove the USB device while the backup is in progress, it may cause a malfunction. If you reuse the removed device, you must format the media by using erase media options.
• If you use the CD/DVD writer device for backup, the backup status will be displayed as shown below. System - 1st. Status of making ISO image - 2nd. Status of writing Daily/Weekly backup 1. Connect the USB device for backup. You cannot use the CD or DVD writer for daily or weekly backup. 2. Select [WEEKLY] or [DAILY] on the schedule options. 3. Select the backup device. 4. Enter the date and/or time to start backup on the schedule start option. 5.
Recording Images from a camera will be recorded on the built-in hard disk. Note: External recording devices can be used as copy areas for images recorded on the hard disk. It is impossible to record images on the external recording devices directly. Instant recording Ensure all the cameras are connected and that time and date have been set correctly. Before you start recording, first check the repeat recording settings in the recording menu of the system setup, and then make the recording settings. 1.
Search and Playback Playback It is possible to play a recorded image without stopping recording. 1. Select a channel you want to playback. 2. Press ad to play a recorded image of the previous 1 or 2 minutes of recording. The playback image will be displayed on the full screen window. 3. Press Z (STOP) to stop the playback. Search The various search functions of this unit can be used to go to the beginning of the desired picture. This unit is equipped with 3 search functions.
10. Use w/s to select the channel you want to playback and press ENTER. Repeat this step to select the other channels. 11. Select the [Time] option and select the start time of the recorded image to playback. Event Search Search a recorded picture by date and type of event. 1. Use w/s to select the [Event Search] option then press ENTER. The event search menu is displayed. 12. Press ad (PLAY) or click the [Play] icon to start playback. The picture(s) is (are) displayed in the main monitor. 13.
Bookmark Search Functions available during playback Search the desired picture with a bookmark registered by the bookmark function. System Control Bar 1. Use w/s to select [Bookmark Search] then press ENTER. The bookmark list menu is displayed. Button Remote Control Front panel Function Stop playback. Pause playback. Press repeatedly to select the required scan speed. (v, vd, vv, vvd or c, ca, cc, cca) Press repeatedly to play frame-by-frame in pause mode. Press to play reverse or normal playback.
LG Network Client Program Introduction The LG Network Client program is an IP-Surveillance software that works with the LG DVR to provide video monitoring, recording setting and event management functions. The software has multiple search functions for recorded events. Remote viewing and playback are also possible with the use of the LG Network Client. This manual contains instructions on how to use and manage the LG Network Client in your networking environment.
Menu Bar Menu File View OSD • Channel Number: Displays or removes the channel number in the channel window. • Site Name: Displays or removes the site name in the channel window. • Camera Name: Displays or removes the camera name in the channel window. • Playback Time: Displays or removes the date/time of playback data in the channel window. • PTZ: Displays PTZ camera icon in the channel window. • Audio: Displays audio icon in the channel window.
Information Display Window Tool Bar Icon Description Displays the live view workspace. Live Search • Camera View: You can see the surveillance camera’s images in the window(s) and the camera information. • Pan/Tilt/Zoom: You can control the PTZ camera. • Log View: You can see the system log list. • Favorites: You can save the current configuration of the camera view. And, it is possible to return to a previous configuration of the camera view.
Operation and settings Using the Dynamic IP Address Register the Site Name or Group Name The first time LG Network Client is started, you should register a site name to control it by the LG Network Client program. The computer running LG Network Client program must be on the same network with DVR. 1. Select [Tools] > [Connection Information] option on the menu bar. The Connection List window is displayed. 2. After completing the settings, click the [OK] button to confirm the settings and exit the window.
Notes: window position. If you select [Cameras] and drag and drop to a live window then all channels are displayed. • If someone logged in the DVR using the Admin ID, you can not log-in using the Admin ID. • If you want to log-out, right click the mouse on the site name and select [User Log-Out]. 7. Repeat steps 3 to 5 to set the other live windows. • Up to 5 users can connect to the DVR system using the client program as shown below. • Configuration of camera view is set the first time only.
Instant playback Confirm the preset position. It is possible to play a recorded image without stopping recording. 1. Select the [Camera View] tab in the live mode. 2. Select a channel you want to playback. 3. Select the date. The day is displayed in a blue text when recorded data exists. 4. Select playback start time. When using timeline to search a start time, use the zoom in/out icons for more detailed searches (4 step). 5. Select playback speed. Use the slider to select the playback speed.
To Clear the Preset Position Favorites Tab You can clear a memorized preset position. You can save the current configuration of camera view. 1. Click the [CLEAR] icon. 2. Use number buttons to enter the memorized preset index number then click the icon to clear the preset positions. This favorite setup is useful for the next time to display it. Note: This function may not be available depending on PTZ cameras. To Tour The Preset Positions You can tour all preset positions. 1. Click the [TOUR] icon.
Using the Search function Event Search Tab Search a recorded picture by date and event type. Date/Time Search Tab Use to search a recorded picture by specifying date, hour and minute. 1. Select the [Event Search] tab. 2. Click the icon and select the day. (The selectable days are displayed in blue color.) Time input column Time line Playback control buttons Displays selected channel number. Mark up when you want to view from all camera channel windows. 3. Select the camera channel for event search. 4.
Using the Remote Setup function You can set the DVR configuration of a selected site name using this function. • Relay Output: Select the number of the ALARM-OUT terminal for the output alarm signal when motion is detected. • Area: The factory default of the Motion detection area is set as the whole area. You can change the area by using mouse on the preview window screen. Camera / Display Setup -- Select area: Click one point with the left mouse button and drag & drop to the end point.
2. Set each option using the mouse (see page 25). Schedule setup 3. Click the [OK] button to confirm the settings. Motion Recording Settings 1. Click the [Motion Recording] button. The motion recording setting window appears. 1. Select a day of the week. 2. Mark up the desired recording option. 2. Set each option using the mouse (see page 25). 3. Click the [OK] button to confirm the settings. Display Settings • No recording: Do not schedule recording.
Schedule Copy Settings Event setup 1. Select the source day to copy. 2. Select the destination day from the day of the week, weekday or weekend options. 3. Click the copy button to copy the schedule data. Special day Settings 1. Set the event options. • Sensor: Displays the number of the ALARM-IN terminal. • Sensor Type: The alarm state can be set to either N.O. (Normally Open) or N.C. (Normally Closed). • Linked Camera: Select the connected camera channel with the ALARM-IN terminal.
Network setup Notification Set the notification options. • Sensor On: Sends an E-mail when a sensor has been detected. • Video Loss: Sends an E-mail when a video signal from the camera has stopped because of a cable disconnection or malfunction of a camera. • Motion Detection: Sends an E-mail when motion detection has occurred. • Power On/Off: Sends an E-mail when power is on or off. • Disk Full: Sends an E-mail when the HDD has fully recorded.
System setup Buzzer settings Select the buzzer options. • Button Beep: Makes a sound when using the buttons. • Sensor: Makes a sound when an sensor occurs. • Motion: Makes a sound when motion is detected. • System: Makes a sound when a HDD has bed sector. Update settings Set the update options. • • Date/Time settings Set the date/time options. • NTP: Mark up when using the NTP (Network Time Protocol) server for time adjustment. • Date Format: Select the date display format.
Using the Export function • You can copy the recorded images and audio data from the DVR unit to the PC. This function is permitted for Administrator and Power user. How to export the data Exit: Click to exit the window. 1. Set the Exprot Channel options. You should select more than one channel. 2. Set the Date/Time options. 3. Select the folder on the computer to save the exported data. 4. Set the export saving capacity. 5. Select the data type. 6. Click [Add] button.
Additional Programs To activate the Emergency Agent program Emergency Agent Program 2. Whenever a notification function occurs, a message box is displayed on the bottom right of the screen. The message box is displayed for 5 seconds. The system sends a message according to the Notification and Emergency settings in the event setup menu. Emergency Agent Overview Display the received message list. Detailed view of the received message. 1. Run the [LG Emergency Agent] program.
Export Viewer Program View You can playback from the export data on the PC using this program. The export viewer program is saved automatically when you install the client program or export the data. Help Export Viewer Overview Menu Bar Language Select the language for Export Viewer program. Video Size Select the video size of the data file. About Export Viewer Displays Export Viewer information. Playback control buttons Jumps to the beginning of the file. Pauses playback. Starts playback.
Web Viewer Program View all the channels in sequence. You can use sequence mode with the one split only. Logging in the Web Viewer You can capture and save the current image in JPEG file format. The initial save folder is “C:\LG Exported Files”. If you want to change the storage folder, set the [Save Path] option on the WebViewer Control Properties Window. 1. Start the web browser. The recommended browser is Internet Explorer with Windows. 2.
Reference Troubleshooting Check the following guide for the possible cause of a problem before contacting service. Symptoms Resolutions Check the power cable is connected correctly. The system power does not turn on. Check the input voltage is correct. If the system power does not turn on even if the power cable is connected correctly, please contact the service center. Check the monitor power cable is connected properly. The system power is turned on but no video data is displayed on the monitor.
Symptoms Audio data recorded with video data is not playing. Resolutions Check the audio recording option is correctly set for the camera you wish to record audio. Check the speaker and audio (line input) on the rear of system are connected correctly. Check the connected speaker is working properly. If the camera connected to the system has a problem, make sure that the camera is not damaged by trying another camera into a working video output.
Symptoms Resolutions E-mail reception failed without SMTP server setting. • Make sure the network is correctly set. • Make sure the mail address is input correctly. • Check the spam mail setting of the inputted mail address. (If you set the spam mail, some mails are deleted automatically or classified in the spam mail box) • Some of SMTP mail services do not support E-mails from private SMTP servers. In this case use the public SMTP server. E-mail reception failed even if the SMTP server was set.
Supported CD/DVD Media list Maker CD-R CD-RW DVD-R DVD-RW DVD+R DVD+RW Imation O O O O O O Memorex O O O O O O MITSUBISHI O O O O O O PHILIPS O O O O O O SONY O O O O O O Verbatim O O O O O O Note: 8 cm (1.4 GB) Mini CD/DVD and the Dual Layer type media (DVD) are not supported.
Time zones Timezone name Eniwetok, Kwajalein Timezone Abbreviation EK Timezone DST -12:00 Midway Island, Samoa MIS -11:00 Hawaii HAW -10:00 Alaska ALA -09:00 -08:00 Pacific Time (US and Canada); Tajuana PST -08:00 -07:00 Mountain Time (US and Canada), Chihuahua, La Paz, Mazatlan, Arizona MST -07:00 -06:00 Central Time (US and Canada), Saskatchewan, Guadalajara, Mexico City, Monterrey, Central America CST -06:00 -05:00 Eastern Time (US and Canada), Indiana (East), Bogota, Lima, Qui
Factory Default Configuration Settings Classification 1st level Camera Schedule Display 66 Detailed Items 2nd level 3rd level Channel Name Camera Covert Audio Channel Port PTZ Control ID Protocol Baud Rate Channel Resolution Quality Recording Frame rate Prealarm Postalarm Channel Resolution Sensor Recording Quality Frame rate Channel Resolution Motion Recording Quality Frame rate Video Format Video Format Sunday Monday Tuesday Wednesday Thursday Friday Saturday Special Day Language OSD Channel Name Cha
Classification 1st level Detailed Items 2nd level Sensor Event Motion Output TCP/IP DDNS Notification Network Mail Emergency SNMP Reference 3rd level Default Setting Input Channel Sensor Type Camera Relay Output Channel Sensitivity Relay Output Relay Off System Alarm Out 01 to 04 N.O. 01 to 04 OFF 01 to 04 05 OFF ALARM ACK.
Classification 1st level System 68 Detailed Items 3rd level Date Time Date Format Time Format Date/Time Time Zone Daylight Saving Daylight Saving Start Daylight Saving End NTP Server NTP Private Time Server Sync.
Recording Time Table (250GB HDD) Resolution (NTSC/PAL) NTSC Quality LOWEST LOW 352x240 / STANDARD 352x288 HIGH HIGHEST Reference FPS PAL Recording Time (Hr) Video Video+Audio 30 1589 1090 20 1895 15 1992 7.5 FPS Recording Time (Hr) Video Video+Audio 25 1123 849 1226 20 1187 884 1266 12.
Resolution (NTSC/PAL) NTSC Quality LOWEST LOW 704x240 / STANDARD 704x288 HIGH HIGHEST 70 FPS PAL Recording Time (Hr) Video Video+Audio 15 1160 869 7.5 1528 5 1625 3 1 FPS Recording Time (Hr) Video Video+Audio 12.5 855 686 1061 6 1021 789 1107 5 1155 867 1790 1181 3 1258 924 2020 1277 1 1907 1231 15 939 739 12.5 734 606 7.5 1164 872 6 934 736 5 1186 884 5 1080 824 3 1414 1005 3 1213 899 1 1355 975 1 1233 910 15 770 630 12.
Resolution (NTSC/PAL) NTSC Quality LOWEST LOW 704x480 / STANDARD 704x576 HIGH HIGHEST FPS PAL Recording Time (Hr) Video Video+Audio 7.5 774 633 5 831 3 944 1 FPS Recording Time (Hr) Video Video+Audio 6 535 464 670 5 726 600 742 3 799 650 1093 831 1 1072 819 7.5 651 548 6 473 417 5 672 563 5 607 516 3 737 608 3 655 551 1 833 672 1 811 658 7.5 598 511 6 407 365 5 605 515 5 551 476 3 655 551 3 589 504 1 712 591 1 675 565 7.
Specifications Item Specification Video Format NTSC/PAL (Selectable) Input 4 x Composite 1.0 Vp-p, 75 Ω BNC Video Loop Through 4 x Composite 1.0 Vp-p, 75 Ω BNC Composite 1 x Composite 1.0 Vp-p, 75 Ω BNC Output VGA 1 x RGB, 15-pin D-sub Spot 1 x Composite 1.
Network Connection Network Bandwidth Control Yes NTP (Network Time Protocol) Yes Application SW Security Button Lock Yes Yes User Level Management Yes Data Integrity Check (Watermark) Yes Triplex Setup Configuration Export/Import Yes Auto Delete (Data Retention) Yes Dome Camera Telemetry Control Yes Interface USB Memory Update Item PTZ, Firmware Video Codec H.
BZ03
