9 INSTALLATION ENGLISH INSTALLATION Installation Overview to another location. 1 Unpacking your refrigerator 4 Connecting the water supply and water line 2 Choosing the proper location 3 Disassembling/Assembling 5 Leveling and Door Alignment “This appliance is intended to be used in household and similar applications such as: motels and others residential type environments. -Bed and breakfast type environments; catering and similar non-reatil applications.
INSTALLATION 10 Specifications Dimensions Net weight Width 32 3/4 in. (833 mm) 32 3/4" (W) X 35 1/2" (D) X 69 7/8" (H), 46" (D w/ door open) 833 mm (W) X 901 mm (D) X 1775.5 mm (H), 1168.5 mm (D w/ door open) Width 29 3/4 in. (756 mm) 29 3/4" (W) X 35 1/2" (D) X 68 1/2" (H), 44 3/4" (D w/ door open) 756 mm (W) X 901 mm (D) X 1740 mm (H), 1137 mm (D w/ door open) Width 32 3/4 in. (833 mm) Width 29 3/4 in. (756 mm) 253 lb. (115 kg) 237.4 lb. (107.
11 INSTALLATION Unpacking Your Refrigerator ENGLISH WARNING Use two or more people to move and install the refrigerator. Failure to do so can result in back or other injury. Your refrigerator is heavy. When moving the refrigerator for cleaning or service, be sure to protect the floor. Always pull the refrigerator straight out when moving it. Do not wiggle or walk the refrigerator when trying to move it, as floor damage could occur.
INSTALLATION Ambient Temperature Measuring the Clearances Too small of a distance from adjacent items may result in lowered freezing capability and increased electricity consumption charges. Allow at least 24 inches (61 cm) in front of the refrigerator to open the doors, and at least 2 inches (5.08 cm) between the back of the refrigerator and the wall.
13 INSTALLATION ENGLISH Removing/Assembling the Freezer Drawer Handle Removing/Assembling the Doors and Drawers Removing the Handle When it is necessary to move the refrigerator through a narrow opening, removing the doors is the recommended procedure. 1 Loosen the set screws located on the lower side of the handle with a 3/32 in. (2.5mm) Allen wrench and remove the handle. 2 Loosen the mounting fasteners that connect to the freezer drawer and handle using a 1/4 in. (6.
INSTALLATION 14 Removing the Left Refrigerator Door . Lift the hook (not visible), located at the bottom of the front side of the cover head screwdriver. 4 Remove the three bolts using a 10mm or hinge. Set parts aside. 2 2 Disconnect the wire harness 3. 3 Remove the grounding screw 4 . 1 CAUTION When lifting the hinge, be careful that the door does not fall forward. 5 Lift the door from the middle hinge pin and remove the door.
15 INSTALLATION Removing the Right Refrigerator Door ENGLISH 1 R emove the top hinge cover screws . Lift the hook (not visible), located at the bottom . with a flatof the front side of the cover head screwdriver. 3 Lift the door from the middle hinge pin and remove the door. 2 CAUTION Place the door, inside facing up, on a non-scratching surface. 2 Remove the three bolts using a 10mm or 13/32-inch socket wrench and lift off the top hinge. Set parts aside.
INSTALLATION 16 ENGLISH Assembling the Right Refrigerator Door Install the right-side door first. 1 Make sure that the plastic sleeve is inserted in the bottom of the door. Lower the door onto the middle hinge pin as shown in the figure. 4 Replace the hinge cover tighten the cover screws 2 2 Align the door with the cabinet 3 Line up the holes in the top hinge with the holes in the top of the refrigerator. Insert and tighten the three bolts in the hinge. . Insert and .
17 INSTALLATION ENGLISH Assembling the Left Refrigerator Door Install the left refrigerator door after the right door is installed. 1 Make sure that the plastic sleeve is inserted in the bottom of the door. Inst all the refrigerator door onto the middle hinge. 4 Replace the grounding screw 3 . 5 Reconnect the wire harness 4 . 6 Replace the hinge cover 5 . Insert and tighten the cover screws 6 .
INSTALLATION 18 Removing the Freezer Drawers 4 Slide out the bar. freezer drawer is not shown for clarity. CAUTION y Use two or more people to remove and install the freezer drawer. Failure to do so can result in back or other injury. y Do not hold the handle when removing or replacing the drawer. The handle may y Be careful of sharp hinges on both sides of the drawer. y When you lay the drawer down, be y Do not sit or stand on the freezer drawer.
19 INSTALLATION Assembling the Freezer Drawers ENGLISH The top, middle and bottom drawers are all assembled in the same way. 1 3 Reinstall the bar in the drawer supports. Using t wo hands, pull out both rails simultaneously until they are fully extended. 4 tighten the screws located on both sides. 2 Grasp the drawer on each side and hook the 3 drawer supports into the rail tabs located on both sides.
INSTALLATION 20 Connecting the Water Line (Ice Maker installed only) This water line installation is not covered by the refrigerator warranty. Follow these instructions carefully to minimize the risk of expensive water damage. Water hammer (water banging in the pipes) in house plumbing can cause damage to refrigerator parts and can lead to water leakage water hammer before installing the water supply line to the refrigerator.
21 INSTALLATION ENGLISH y If your existing copper water line will need an adapter (available at plumbing supply stores) to connect the water line to the refrigerator OR with a tube cutter and then use a y Shutoff valve to connect to the cold water line. have a water inlet with a minimum inside diameter of 5/32 in. (4 mm) at the point of connection to the COLD valves are included in many water supply kits. Before purchasing, make sure a saddletype valve complies with your local plumbing codes.
INSTALLATION 22 Water Line Installation Instructions 4 y When using any electrical device (such as a power drill) during installation, be sure the device is battery powered, double insulated or grounded in a manner that will prevent the hazard of electric shock. pipe with the pipe clamp. Pipe Clamp S a d d l e - Ty p e used drinking water line. 1 SHUT OFF THE MAIN WATER SUPPOLE Turn on the nearest faucet to relieve the pressure on the line.
23 7 INSTALLATION CONNECT THE TUBING TO THE VALVLE ENGLISH Place the compression nut and ferrule (sleeve) for copper tubing onto the end of 1 0 TURN THE WATER ON AT THE SHUTOFF VALVE Tighten any connections that leak. valve. Make sure the tubing is fully inserted into the valve. Tighten the compression nut securely. Saddle-Type Compression Nut Packing Nut Outlet Valve 8 Ferrule (sleeve) CAUTION Check to see if leaks occur at the water line connections.
INSTALLATION 24 Leveling and Door Alignment 1 Plug in the refrigerator. Leveling After installing, plug the refrigerator’s power cord into a 3-prong grounded outlet and push Your refrigerator has two front leveling legs— one on the right and one on the left. Adjust the legs to alter the tilt from front-to-back or side-toside.
25 INSTALLATION Door Alignment ENGLISH Identify your Refrigerator Doors alignment type according the accesory included in your owner’s manual. Door Alignment (Type 1) Door Alignment (Type 2) Both the left and right refrigerator doors have an adjustable nut, located on the bottom hinge, to raise and lower them to align properly.
