Installation Guide

ManualsBrandsLG ManualsFrench Door RefrigeratorsLFDS22520S

HOW TO REMOVE AND INSTALL THE REFRIGERATOR DOORS

For moving the refrigerator through a house door, it might be necessary to remove refrigerator and freezer door

handles.

NOTE: Removing the doors is always recommended when it is necessary to move the refrigerator through a narrow

opening. If it is necessary to remove the handles, follow the directions below.

TOOLS YOU MIGHT NEED OR USE

3/8 in (10 mm)

1/4 in (6 mm)

Hex Socket Wrench Phillips Screwdriver Flat Head Screwdriver Allen Wrench

HOW TO REMOVE REFRIGERATOR DOOR HANDLE

NOTE: Handle appearance may vary from

illustrations on this page.

Loosen the set screws with a 3/32 in (2,5 mm). Allen

wrench and remove the handle.

NOTE: If the handle mounting fasteners need to be

tightened or removed, use a 1/4 in (6 mm). Allen

wrench.

HOW TO REPLACE REFRIGERATOR DOOR HANDLE

NOTE: Handle appearance may vary from

illustrations on this page.

Place the handle on the door by ﬁtting the handle

footprints over the mounting fasteners and tightening

the set screws with a 3/32 in (2,5 mm) Allen wrench.

NOTE: If the handle mounting fasteners need to be

tightened or removed, use a

1/4 in (6 mm) Allen wrench.

REFRIGERATOR INSTALLATION

Mounting

Fasteners

Set Screw

Allen

Wrench

1/4 in (6 mm)

3/32 in (2,5 mm)

Summary of content (7 pages)

PAGE 1
REFRIGERATOR INSTALLATION HOW TO REMOVE AND INSTALL THE REFRIGERATOR DOORS For moving the refrigerator through a house door, it might be necessary to remove refrigerator and freezer door handles. NOTE: Removing the doors is always recommended when it is necessary to move the refrigerator through a narrow opening. If it is necessary to remove the handles, follow the directions below.
PAGE 2
REFRIGERATOR INSTALLATION NOTE: Removing the doors is always recommended when it is necessary to move the refrigerator through a narrow opening. If it is necessary to remove the handles, follow the directions below. HOW TO REMOVE FREEZER DOOR HANDLE NOTE: Handle appearance may vary from illustrations on this page. Loosen the set screws located on the lower side of the handle with a 3/32 in (2,5 mm). Allen wrench and remove the handle.
PAGE 3
REFRIGERATOR INSTALLATION CAUTION: Before you begin, remove food and bins from the doors. REMOVING AND REPLACING REFRIGERATOR DOORS WARNING (1) (2) Excessive Weight Hazard: Use two or more people to remove and install the refrigerator doors. Failure to do so can result in back or other injury. (3) (4) (7) (5) WARNING (6) Electrical Shock Hazard ţ Disconnect the electrical supply to the refrigerator before installing. Failure to do so could result in serious injury or death.
PAGE 4
REFRIGERATOR INSTALLATION Reinstalling the Refrigerator Door Right Door Left Door 1. Lower the door onto middle hinge pin (9). 2. Line up the holes in the top hinge with the holes in the top of the refrigerator. Insert and tighten the three Bolts (6) in the hinge. 3. Hook the tabs on right side of hinge cover (2) under the edge of the top hinge (4) and position the cover in place. Insert and tighten the cover screw (1). 1. Lower the door onto middle hinge pin (10). 2.
PAGE 5
REFRIGERATOR INSTALLATION HOW TO REMOVE THE FREEZER DRAWER WARNING: Use two or more people to remove and install the freezer drawer. Failure to do so can result in back or other injury. Remove the screws (2) of the rail on both sides. 2 CAUTION: Do not hold the handle when removing or replacing the drawer. The handle may come off, causing personal injury. To remove, pull the drawer out to full extension. Lift the drawer up and out, making sure to clear the rail system.
PAGE 6
REFRIGERATOR INSTALLATION HOW TO REPLACE THE FREEZER DRAWER With the drawer pulled out to full extension, insert the lower basket 4 in the rail assembly. Pull out each rail to full extension. 4 Grasp the drawer on each side and hook door supports 1 into the rail tabs 2 located on both sides. To replace, with the drawer pulled out to full extension, insert the drawer in the rail assembly. 1 2 Lower the door into its ﬁnal position and tighten the screws 3 located on both sides.
PAGE 7
REFRIGERATOR INSTALLATION LEVELING AND DOOR ALIGNMENT Door Alignment Leveling If the space between your doors is uneven, follow the instructions below to align the doors: After installing, plug the refrigerator’s power cord into a 3-prong grounded outlet and push the refrigerator into the ﬁnal position. Your refrigerator has two front leveling legs—one on the right and one on the left. Adjust the legs to alter the tilt from frontto-back or side-to-side.