Engineering Manual

VERTICAL-HORIZONTAL INDOOR UNITS
,QVWDOODWLRQDQG%HVW/D\RXW3UDFWLFHV
Drain Piping Specifications
• Drain piping must have downward gradient of at
OHDVWWRWRSUHYHQWUHYHUVHIORZVORSH
should not be straight up and down.
• Do not damage the drain port on the indoor unit
when connecting the field-supplied drain piping.
Drain Hole
Gaps Should Not Be Present
Unit
Drain Piping
(Field Supplied)
Drain Piping Insulation
(Field Supplied)
U-Trap
B
C
A
3/4-inch Connector
Field-Installed U-Trap Specifications
)LJXUHClose up of Drain Piping Connection.
)LJXUHInstalling the U-Trap.
7RSUHYHQWOHDNVFDXVHE\DEORFNLQWKHLQWDNHDLU¿OWHULQVWDOOD87UDS
$LQFKHV
%&
&[63
63 ([WHUQDO3UHVVXUHLQ:*
Example:
([WHUQDO3UHVVXUH LQ:*
$LQFKHV
%LQFKHV
&LQFKHV
Drain Access Hole
Air Filter Cover
Main Drain with Suitable Trap. (Field-Supplied
Trap with Sufficient Depth Can Be Used.
Standard Size P-Traps Cannot Be Used.
Supplementary Drain with a
Proper Trap (Field Supplied Kit
Can Be Used)
Figure 226: Vertical Primary and
6HFRQGDU\'UDLQ/D\RXW
Figure 227: Horizontal Primary and
6HFRQGDU\'UDLQ/D\RXW
Refrigerant Piping Insulation
Field-installed vapor and liquid refrigerant piping lines must be
properly and completely covered in insulation (up to the indoor
unit piping connections) and must comply with federal, state,
and local requirements. Any exposed piping may generate
condensate or will cause burns if touched. Insulation for this
field-installed refrigerant piping must have a minimum heat
UHVLVWDQFHRI)
Vertical-horizontal air handling indoor units have been tested
XQGHUDQGPHHWWKHUHTXLUHPHQWVRIWKH³.6&RQGLWLRQV´,IWKH
indoor unit is installed and is operated at an extended period
LQDKLJKO\KXPLGHQYLURQPHQWGHZSRLQWWHPSHUDWXUH!)
however, condensate will form. To prevent this phenomenon,
install adiabatic glass wool insulation with a thickness of 7/16
to 13/16 inches thick. Also, install glass wool insulation on all
indoor units that are located in the ceiling plenum.
Drain Piping Insulation
Drain piping insulation must be 7/32 inches thick, minimum.
Insulating the Refrigerant and
Drain Piping
Connection for Liquid Piping
Refrigerant Piping
Insulation (Field Supplied)
Connection for Vapor Piping
Insulation Zip Tie (Field Supplied)
Refrigerant Piping Insulation (Field
Supplied)
Figure 228: Close Up of Refrigerant Piping Connection Insulation.
Gaps Should Not be Present
Overlap Piping Insulation
Refrigerant Piping Insulation (Field Supplied)
Insulation Clip (Field Supplied)
Refrigerant Piping Insulation
(Field Supplied)
)LJXUHInsulating the Refrigerant Piping and Refrigerant Piping
Connections.
(QVXUHDOOSLSLQJLVLQVXODWHG([SRVHGSLSLQJFDQFDXVH
EXUQVLIWRXFKHG
'XHWRRXUSROLF\RIFRQWLQXRXVSURGXFWLQQRYDWLRQVRPHVSHFL¿FDWLRQVPD\FKDQJHZLWKRXWQRWL¿FDWLRQ
©/*(OHFWURQLFV86$,QF(QJOHZRRG&OLIIV1-$OOULJKWVUHVHUYHG³/*´LVDUHJLVWHUHGWUDGHPDUNRI/*&RUS
160 | VERTICAL-HORIZONTAL
Multi F and Multi F MAX Indoor Unit Engineering Manual
MULTI
F
MAX
MULTI
F