Owner's Manual

17
Before
Operation-VCR part
Tuning
in
a video channel on
your
TV
Notes
?
The
output frequency
of this video recorder
(VCR)
is
set at UHF channel 36. If channel 36 is
already
used
by
another TV
station,
or if the
picture
is
distorted,
you
can
change
the transmitter channel of
your
DVD/VCR Combi receiver.
Stages
5
~
8 will
show
you
how to
change
the
output frequency
of
your
DVD/VCR Combi receiver.
?Y our TV receives
signals
from the video recorder
(VCR)
like another TV station. You have to select a
channel number on
your
TV and tune it in so that
you may
watch video
tapes.
If
you
have used a
RCA-SCART cable then
your
TV should
already
have a dedicated video channel built into
it,
usu-
ally
called AV.
1. Make sure that
you
have
correctly
installed
your
VCR as described earlier in this book.
Press POWER to turn on
your
DVD/VCR Combi
receiver. Turn on
your
TV.
2. Insert a
pre-recorded
video
tape
into
your
DVD/VCR Combi receiver and
press
PLAY on the
remote control. Select a TV channel number on
which
you
wish to watch video's.
Don't
worry
if
you
don't have a
video-tape
to
play
at this
stage!
If
you
switch
your
DVD/VCR Combi
receiver on and continue
stages
3
~
4,
instead of
seeing
video
playback
tune
your
TV until
you
see
a
bright
blue screen.
3. Tune this channel until the video
picture
is
sharp
and the sound is clear.
If
you
have used a RCA-SCART cable
you
will not
have to tune
your
TV,
simply
select the AV
channel. The AV channel is
already pre-tuned
for
optimum
video
playback
on
your
TV.
4. Store this channel on
your
TV.
You will need to look at the TV instruction book if
you
do not know how to do this.
5.
Only carry
out
stages
5
~
8 if
you
cannot
obtain clear video
playback
as described
in
stages
1
~
4. Select a TV channel number on
which
you
wish to watch video's.
Make sure that
your
DVD/VCR Combi receiver is
in
standby pressing
POWER on the remote control
(only
the clock will be
displayed).
6. Press
PROG.
3 or 4 on the front of
your
DVD/
VCR Combi receiver for more than 4 seconds.
RF36 will
appear
in the
display
window.
The
following picture
will be
displayed
on the TV
screen.
7. Press 3 or 4 to select another video channel. You
may
select
any
channel number between 22 and
68.
You can also set it to "OFF" if there is
any
interfer-
ence when
your
TV is connected to the DVD/VCR
Combi receiver with a RCA-SCART lead.
8. Select a TV channel number on which
you
wish to
watch video's.
Press STANDBY/ON on the front of
your
DVD/VCR Combi receiver when
you
have finished.
Tune this channel so that a
bright
blue screen
appears.
Store this channel on
your
TV.
Notes
Make sure that
you
have
correctly
installed
your
DVD/VCR Combi receiver and
successfully
tuned in a
dedicated video channel on
your
TV. If
you
do not
tune in a dedicated video channel on
your
TV
you
will
be unable to view and record video
tapes!
Initial
preset
For the
following steps
we do assume that
you
have
just
connected
your
video recorder for the
very
first
time. In this case the video recorder is on after mains
connection. You should not touch
any
buttons
yet.
On
the connected TV
you
will now see.
Note
-
If this menu does not
appear, your
video
recorder was
programmed already.
1. Select the
country according
to
your
area with
F
andG.
"A":
Austria,
"B":
Belgium,
"CH":
Switzerland,
"D":
Germany,
"DK":
Denmark,
"E":
Spain,
"F":
France,
"I":
Italy,
"N":
Norway,
"NL":
Netherlands,
"P":
Portugal,
"S":
Sweden,
"SF":
Finland,
OTHERS.
2. Press OK to start the automatic
storing
of the
channels of the TV stations in
your
area.
RF KAHA 36
PSET
R
A
NN L PSS F
BD D K EFI
Pr-12
ACMS
CH
Pr-12
ACMS
01 C02 00 PR-01
E S