Owner's Manual
Before
Operation
16
AUDIO
Each
DVD
disc
has
a
variety
of
audio
output
options.
Set
the
player's
AUDIO
options
according
to
the
type
of
audio
system
you
use.
Dolby
Digital
/
DTS
/
MPEG
Bitstream:
Select
"Bitstream"
if
you
connect
the
DVD
Player's
DIGITAL
OUT
jack
to
an
amplifier
or
other
equipment
with
a
Dolby
Digital,
DTS
or
MPEG
decoder.
PCM
:
Select
when
connected
to
a
two-channel
digi-
tal
stereo
amplifier.
DVDs
encoded
in
Dolby
Digital
or
MPEG
will
be
automatically
downmixed
to
two-chan-
nel
PCM
audio.
Sample
Freq.
(Frequency)
If
your
receiver
or
amplifier
is
NOT
capable
of
handling
96
kHz
signals,
select
48
kHz.
When
this
choice
is
made,
this
unit
automatically
converts
any
96
kHz
signals
to
48
kHz
so
your
system
can
decode
them.
If
your
receiver
or
amplifier
is
capable
of
handling
96
kHz
signals,
select
96
kHz.
When
this
choice
is
made,
this
unit
passes
each
type
of
signal
through
without
any
further
processing.
Check
the
documentation
for
your
amplifier
to
verify
its
capabilities.
2.1
Speaker
Setup
Speaker
Setup
Make
the
following
settings
for
the
built-in
2.1
channel
surround
decoder.
1.
Press
SETUP.
The
setup
menu
appears.
2.
Use
v
/
V
to
select
the
AUDIO
option
then
press
B
to
move
to
the
second
level.
3.
Use
v
/
V
to
select
the
Speaker
Setup
option
then
press
B
to
move
to
the
third
level.
"Select"
is
high-
lighted.
4.
Press
SELECT/ENTER
and
2.1
Speaker
Setup
menu
appears.
5.
Use
b
/
B
to
select
the
desired
speaker.
6.
Adjust
options
using
v
/
V
/
b
/
B
buttons.
7.
Press
SELECT/ENTER
to
confirm
your
selection.
Returns
to
the
previous
menu.
Speaker
selection
Select
a
speaker
that
you
want
to
adjust.
[Front
speaker
(Front
L),
Front
speaker
(Front
R)
or
Subwoofer
(Woofer)]
Size
Press
b
/
B
to
set
a
mode.
(Large,
Small
or
None)
?
The
size
of
the
Front
L/R
speaker
can
be
selected
to
"Large"
or
"Small".
?
The
size
of
the
Subwoofer
can
be
selected
to
"Large"
or
"None".
?
If
you
have
connected
the
system
to
a
speaker
with
low
frequency
of
100Hz
or
below,
select
to
"Large"
the
size
of
the
Front
L/R
speaker.
The
size
of
the
Subwoofer
is
selected
to
"None"
automatically.
?
If
you
have
connected
the
system
to
a
speaker
without
low
frequency
of
100Hz
or
below,
select
to
"Small"
the
size
of
the
Front
L/R
speaker.
The
size
of
the
Subwoofer
is
selected
to
"Large"
automatically.
But
if
you
haven't
connected
to
subwoofer,
always
select
to
"Large"
the
size
of
Front
L/R
Speaker.
Volume
Press
b
/
B
to
adjust
the
output
level
of
the
selected
speaker.
(-5dB
~
5dB)
Distance
This
function
is
not
available
to
the
unit.
Test
Select
"All"
to
test
the
signals
of
each
speaker.
Adjust
the
volume
to
match
the
volume
of
test
signals
memorized
in
the
system.
(When
the
size
of
the
Front
L/R
speaker
is
selected
to
"Large",
the
subwoofer
(Woofer)
is
not
available.)
Front L
→
Front
R
→
Woofer
You
can
adjust
the
volume
during
operating
the
test
tone,
first
use
v
/
V
to
select
Volume
or
Speaker
option
then
use
b
/
B
buttons
to
select
volume
or
speaker,
so
that
all
speaker's
volume
is
same
from
the
listener's
position.
DVD
DVD
DVD
Dolby
Digital
Bitstream
PCM
48
kHz
Bitstream
DTS
MPEG
Sample
Freq.
Select
On
2.1
Speaker
Setup
DRC
On
Vocal
Move
Select
AUDIO