Owner's Manual

Before
Operation
PREPARATION
13
Setting
the Clock
1
Press
CLOCK.
(If
the clock
requires setting, press
and hold CLOCK
for more than 2
seconds.)
-
The hours
display begins
to blink.
2.
Select either the
12 hour
cycle
or
the
24 hour
cycle by turning
MULTI
JOG
DIAL.
3
Press
SET
to confirm the selected
hour
cycle.
4
Use
MULTI
JOG
DIAL
to set the current
hour.
5
Press
SET.
6.
Use
MULTI
JOG
DIAL
to set current minutes.
7
Press
SET
and the correct time is shown
on
the
display.
ote
When the clock is not
appeared
in the
display
window,
follow as below.
-
In case the clock is
set,
prese
the CLOCK button.
The clock will be shown in the
display
window for
about 5 seconds.
-
In case the clock is not
set,
the clock will be blinked in
the
display
window for about 1 minute. Set the clock
as above.
Sleep
Timer Function
When the
sleep
timer is
set,
the unit
automatically
turns
off after the
specified
time has
elapsed.
1
To
specify
the time
delay
before the
power
is
turned
off,
press
SLEEP.
In the
display
window
you
can see
SLEEP 180
for
about 5 seconds. This means that the
system
turns
off
automatically
after 180 minutes.
2
Each time
you press
SLEEP
the
setting changes
in
the
following
order.
SLEEP 180 →150
→
120 →90→80→70
→
60→ 50
→
40
→
30
→
20 →10
→
OFF
(No display)
→SLEEP 180...
3
To
check the
remaining
time until the
power
is
turned
off.
While the
sleep
function is active
press
SLEEP
briefly.
The time
remaining
until the unit turns off is
displayed
for about 5 seconds.
ote
If
you press
SLEEP while the
sleep
time is
displayed,
the SLEEP time is reset.
To cancel
Sleep
Timer
setting
If
you
wish to
stop
the
function,
press
the SLEEP button
repeatedly
until
"SLEEP 10
"
appears,
and then
press
SLEEP once
again
after
"SLEEP 10
"
shows on the
display.
Using Microphone
-
OPTIONAL
You can
sing
to a music source
by connecting
a
microphone
to the unit.
Connect
your microphone
to the
MIC
socket.
""
will be shown in the
display
window.
2
Play
a
music
you
want.
Sing along
with the
accompaniment.
Adjust
the
microphone
volume
by turning
MIC
VOLUME KNOB.
For
your
reference
You can record
during using microphone.
Refer to the
"Recording" explanation
section.
otes
When not
using
the
microphone,
set the MIC volume
knob to minimum or turn off the MIC and remove the
microphone
from the MIC socket.
If the
microphone
is set too near the
speaker,
a
howling
sound
may
be
produced.
In this
case,
move
the
microphone away
from the
speaker
or decrease
the sound level
by using
the MIC volume control.
If sound
through
the
microphone
is
extremely
loud,
it
may
be distorted. In this
case,
turn the MIC volume
control toward minimum.
To
Adjust
ECHO Volume
You can
give
an echo effect to the sound from the
microphone.
Press the ECHO
repeatedly.
ECHO-OFF→ECHO-1→ECHO-2 →ECHO-3
(12HR) (24HR)
or