User guide

Precautions
• Be sure to switch off the unit before installation and connection.
• The installation should be made by qualified service personnel or system installers.
• Do not expose the power and connection cables to moisture, which may cause damage to
the unit.
Connecting Network
You can control and monitor the system via network. With the remote control (monitoring), you
can change the system configuration or monitor the image via network. After the installation,
check the network settings for the remote control and monitoring work.
Connect the IP camera to your network using a standard RJ-45 network cable as shown below.
ETHERNET
With PoE
Broadband
Service
Broadband
Service
PoE Device
(IEEE802.3af )
Router
Connecting Power Source
Connect power, using one of the methods listed below:
To use the power adapter
Connect a DC 12 V power source to the power input terminal as shown below.
(recommended power adapter is DC 12 V/1.5 A or above)
POWER IN
DC 12 V
ETHERNET
With PoE
To use the PoE (Power over Ethernet) device
Connect the PoE cable to the LAN port on the unit. You must use the “IEEE802.3af” standard PoE
device.
POWER IN
DC 12 V
ETHERNET
With PoE
PoE Device
(IEEE802.3af )
NOTE:
If the camera doesn’t work properly after connecting PoE device, please check if the PoE device
supplies enough power.
Using the micro SD card
You can record your surveillance environment with the micro SD card even if the network is
disconnected condition.
To insert the micro SD card
1. Remove the Dome Cover.
2. Insert the micro SD card carefully as shown in the following illustrations. Make sure the micro
SD card terminal position before insert the micro SD card. Push the back end of the micro
SD card to fix it at the last step.
NOTES:
• Do not use the power too much when you insert the micro SD card. The micro SD card may
be damaged.
• If you insert the micro SD card in the wrong position, the micro SD card may be damaged or
it may cause the malfunction of the micro SD Card Slot.
• Keep the terminal part of the micro SD card in clean. Be careful the terminal part of the
micro SD card not to dusty.
• As the micro SD card is consumable, the micro SD card end its days and may be not able to
save data if you use it more than over certain times. In this case, replace micro SD card to
buy a new one.
Remove the micro SD card
1. Press the back end of the micro SD card to release the lock condition.
2. Take the micro SD card out carefully from the camera. It may cause a malfunction of the
micro SD card or the micro SD card slot if you use the power too much at lock status.
CAUTION:
• If you install the micro SD card on the camera and remove with the micro SD card condition
indicator lights on, you must unmount the micro SD card by using the [System > Storage
> Device Management > Unmount] menu. The micro SD card data is compromised or the
camera may not operate normally, if you remove the card without use [Unmount] function.
• LG Electronics is not responsible for deleted data caused by user mishandling when you
insert or remove the micro SD card.
Recommended the micro SD card specification
Maker Capacity
Block Size
(FAT 32)
LG
Less than
32 GB
32 kbyte
Sandisk
Transcend
NOTE:
Speed of reading and writing more than 10 MB/Sec. (Class 6)
Connection
Follow the instructions below to surface mount the camera with supplied camera mounting
bracket.
1. Use the installation guide template to check the mounting location. Face the front of the
label toward the area of interest. Using the template as a guide, make a hole through the
ceiling.
FRONT
PRODUCT CENTER POSITION
MEZ62687703
4 Place
SELFTAPPING SCREW
CABLE HOLE (LCV5300)
CABLE HOLE (LCD5300)
FRONT
PRODUCT CENTER POSITION
MEZ62687703
4 Place
SELFTAPPING SCREW
CABLE HOLE (LCV5300)
CABLE HOLE (LCD5300)
FRONT
PRODUCT CENTER POSITION
MEZ62687703
4 Place
SELFTAPPING SCREW
CABLE HOLE (LCV5300)
CABLE HOLE (LCD5300)
FRONT
PRODUCT CENTER POSITION
MEZ62687703
4 Place
SELFTAPPING SCREW
CABLE HOLE (LCV5300)
CABLE HOLE (LCD5300)
CAUTION:
Install on a ceiling or wall where can withstand the weight of 5 times of the camera including
mounting bracket.
2. Pass the connection cable through the inner side of the ceiling.
FRONT
PRODUCT CENTER POSITION
MEZ62687703
4 Place
SELFTAPPING SCREW
CABLE HOLE (LCV5300)
CABLE HOLE (LCD5300)
FRONT
PRODUCT CENTER POSITION
MEZ62687703
4 Place
SELFTAPPING SCREW
CABLE HOLE (LCV5300)
CABLE HOLE (LCD5300)
FRONT
PRODUCT CENTER POSITION
MEZ62687703
4 Place
SELFTAPPING SCREW
CABLE HOLE (LCV5300)
CABLE HOLE (LCD5300)
FRONT
PRODUCT CENTER POSITION
MEZ62687703
4 Place
SELFTAPPING SCREW
CABLE HOLE (LCV5300)
CABLE HOLE (LCD5300)
3. Install the camera mounting bracket to the ceiling.
FRONT
PRODUCT CENTER POSITION
MEZ62687703
4 Place
SELFTAPPING SCREW
CABLE HOLE (LCV5300)
CABLE HOLE (LCD5300)
FRONT
PRODUCT CENTER POSITION
MEZ62687703
4 Place
SELFTAPPING SCREW
CABLE HOLE (LCV5300)
CABLE HOLE (LCD5300)
FRONT
PRODUCT CENTER POSITION
MEZ62687703
4 Place
SELFTAPPING SCREW
CABLE HOLE (LCV5300)
CABLE HOLE (LCD5300)
FRONT
PRODUCT CENTER POSITION
MEZ62687703
4 Place
SELFTAPPING SCREW
CABLE HOLE (LCV5300)
CABLE HOLE (LCD5300)
4. Connect the cables to the cable jacks of the camera body.
FRONT
PRODUCT CENTER POSITION
MEZ62687703
4 Place
SELFTAPPING SCREW
CABLE HOLE (LCV5300)
CABLE HOLE (LCD5300)
FRONT
PRODUCT CENTER POSITION
MEZ62687703
4 Place
SELFTAPPING SCREW
CABLE HOLE (LCV5300)
CABLE HOLE (LCD5300)
FRONT
PRODUCT CENTER POSITION
MEZ62687703
4 Place
SELFTAPPING SCREW
CABLE HOLE (LCV5300)
CABLE HOLE (LCD5300)
FRONT
PRODUCT CENTER POSITION
MEZ62687703
4 Place
SELFTAPPING SCREW
CABLE HOLE (LCV5300)
CABLE HOLE (LCD5300)
5. Assemble the camera and mounting bracket after align the front part of the camera and
mounting bracket. Connect the unit by following step a and b.
FRONT
PRODUCT CENTER POSITION
MEZ62687703
4 Place
SELFTAPPING SCREW
CABLE HOLE (LCV5300)
CABLE HOLE (LCD5300)
FRONT
PRODUCT CENTER POSITION
MEZ62687703
4 Place
SELFTAPPING SCREW
CABLE HOLE (LCV5300)
CABLE HOLE (LCD5300)
FRONT
PRODUCT CENTER POSITION
MEZ62687703
4 Place
SELFTAPPING SCREW
CABLE HOLE (LCV5300)
CABLE HOLE (LCD5300)
FRONT
PRODUCT CENTER POSITION
MEZ62687703
4 Place
SELFTAPPING SCREW
CABLE HOLE (LCV5300)
CABLE HOLE (LCD5300)
NOTE:
To disassemble the camera from the mounting bracket, rotate the camera counterclockwise with
pressing the PUSH button inside the camera body.
Mounting the camera