User guide

Part Names and Functions
a
d
b
c
e
f
g
h
i j k l
a Dome Cover
b IR Sensor
c IR LED
Do not stare at operating IR LED within hazard distances (1 m).
,
d micro SD card slot
Insert the micro SD card.
e Jog button
Use this button for control the Zoom / Focus of the camera.
(Left : Wide, Right : Tele, Up : Near, Down : Far, Push : Auto Focus)
f Video Out Connector
Use this jack for checking the picture with portable monitor when install the camera.
g RESET button
Push the button more than 3 seconds, this would restore the factory default network related
settings.
h Camera mounting bracket
You can lock the camera mounting bracket by tighten the screws.
To disassemble the camera from the mounting bracket, rotate the camera
counterclockwise with pressing the PUSH button inside the camera body.
,
i AUDIO IN / OUT (Line Level Input / Output)
j ALARM IN & OUT / ALARM IN & OUT RETURN
Provides physical interface for sensor and Alarm/Relay.
k Power input terminal
Connects to a DC 12 V power supply using proper cables. This camera must always be operated
a DC 12 V. Certied/Listed Adaptor which comply with LPS.
l ETHERNET/PoE Port
Connects to a PC or a network via a hub with a 10 BASE-T/100 BASE-TX cable attached
RJ-45 connector.
Power over Ethernet (PoE) is a technology that integrates power into a standard LAN
infrastructure. It enables power to be provided to the network device, such as a network
camera, using the same cable as that used for network connection. It eliminates
the need for power outlets at the device locations and enables easier application of
uninterruptible power supplies (LPS).
,
Installation
Using the micro SD card
You can record your surveillance environment with the micro SD
card even if the network is disconnected condition.
To insert the micro SD card
1. Remove the Dome Cover.
2. Insert the micro SD card carefully as shown in the following
illustrations. Make sure the micro SD card terminal position
before insert the micro SD card. Push the back end of the
micro SD card to x it at the last step.
• Do not use the power too much when you insert the
micro SD card. The micro SD card may be damaged.
• If you insert the micro SD card in the wrong position,
the micro SD card may be damaged or it may cause
the malfunction of the micro SD Card Slot.
• Keep the terminal part of the micro SD card in clean.
Be careful the terminal part of the micro SD card not
to dusty.
• As the micro SD card is consumable, the micro SD
card end its days and may be not able to save data if
you use it more than over certain times. In this case,
replace micro SD card to buy a new one.
,
Remove the micro SD card
1. Press the back end of the micro SD card to release the lock
condition.
2. Take the micro SD card out carefully from the camera. It may
cause a malfunction of the micro SD card or the micro SD
card slot if you use the power too much at lock status.
• If you install the micro SD card on the camera
and remove with the micro SD card condition
indicator lights on, you must unmount the micro
SD card by using the [System > Storage > Device
Management > Unmount] menu. The micro SD
card data is compromised or the camera may not
operate normally, if you remove the card without use
[Unmount] function.
• LG Electronics is not responsible for deleted data
caused by user mishandling when you insert or
remove the micro SD card.
Recommended the micro SD card specication
Maker Capacity
Block Size
(FAT 32)
LG
Less than 32 GB 32 kbyteSandisk
Transcend
Speed of reading and writing more than 10 MB/Sec.
(Class 6)
,
Mounting the camera
Follow the instructions below to surface mount the camera with
supplied camera mounting bracket.
1. Use the installation guide template to check the mounting
location. Face the front of the label toward the area of
interest. Using the template as a guide, make a hole
through the ceiling.
2. Disassemble the camera from the mounting bracket.
Install the camera mounting bracket to the ceiling.
3. Connect the cables to the cable jacks of the camera body. 4. Assemble the camera and mounting bracket after align the
front part of the camera and mounting bracket. Connect
the unit by following step a and b.
• Be careful of sharp edge after removing the cap of
cable conduit.
• Arrange the cables by cable tie after installation.
,
Camera Adjustment
1. Connect the portable monitor to the video jack using the
test monitor cable.
2. Adjust the Pan / Tilt / Rotation position of the camera.
ROTATION
TILT
PAN
• Manual adjustment:
PAN: 360° / TILT: 75° / ROTATION: 355°
• When you adjust PAN/TILT/ROTATION manually,
be careful your hand is not to hurt by protrusions of
other part.
• The camera could be damaged by adjusting Pan, Tilt
by force.
,
Connection
Precautions
• Be sure to switch o the unit before
installation and connection.
• The installation should be made by qualied
service personnel or system installers.
• Do not expose the power and connection
cables to moisture, which may cause
damage to the unit.
Connecting Network
You can control and monitor the system via
network. With the remote control (monitoring),
you can change the system conguration
or monitor the image via network. After the
installation, check the network settings for the
remote control and monitoring work.
Connect the IP camera to your network using a
standard RJ-45 network cable as shown below.
Broadband
Service
PoE Device
(IEEE802.3af )
Broadband
Service
Router
Connecting Power Source
Connect power, using one of the methods
listed below:
To use the power adapter
Connect a DC 12 V power source to the power
input terminal as shown below.
(Recommended power adapter is DC 12 V /
1.5 A or above)
2
3
To use the PoE (Power over Ethernet) device
Connect the PoE cable to the LAN port on the
unit. You must use the “IEEE802.3af” standard
PoE device.
PoE Device
(IEEE802.3af )
If the camera doesn’t work properly after
connecting PoE device, please check if
the PoE device supplies enough power.
,
Connecting Alarm Device
Alarm terminals are used to connect the alarm
(relay) devices such as sensors, door switches,
etc.
ALARM IN & OUT / ALARM IN & OUT RETURN
(Sensor Input / Relay Output)
Connect the sensor device and alarm (relay)
device to the alarm terminal. Alarm signal is
outputted at an event occurrence.
Alarm (relay)
Device
Sensor
Device
• The Photo MOS Relay is rated for
100 mA at DC 20 V or 100 mA at
AC 28 V.
• Grasp both ends of the 3 or 4 pin
connector plug and then sway both
side to pull it out.
,
Connecting Microphone and
Speaker Device
Optionally connect an active speaker and/or
external microphone with a built-in amplier.
Audio OUTAudio IN
Keep the microphone away from the
speaker to avoid howling.
,
• When the connecting Alarm and
Audio, tighten the screws as shown
above.
• Put your nger between the power
connector and the camera body to
pull out the connector.
,