INSTALLATION 11 INSTALLATION Installation Overview Please read the following installation instructions first after purchasing this product or transporting it to another location. a Unpacking the Refrigerator b Choosing the Proper Location c Disassembling/Assembling d Connecting the Water Line e Leveling and Door Alignment WARNING water supply only.
12 INSTALLATION Unpacking the Refrigerator install a booster pump to compensate for the low pressure. WARNING to move and install the refrigerator. Failure to do so can result in back injury or other injury. moving the refrigerator for cleaning or service. Always pull the refrigerator straight out when moving it. Do not wiggle or walk the refrigerator when trying to move it, as floor damage could occur. gasoline, away from the refrigerator. Failure to do so can result in fire, explosion, or death.
INSTALLATION 13 Dimensions and Clearances nce and the installation path to ensure there is sufficient room to move the refrigerator through doors or narrow openings. and airflow and space in front to open the doors and drawers. result in lowered freezing capability and increased electricity consumption charges. Allow at least 2 inches (50 mm) between the back of the refrigerator and the wall. in front of the refrigerator to fully open the doors and drawers.
14 INSTALLATION - Flat-head screwdriver - Phillips screwdriver Removing the Hinge Cover Remove the screws from the hinge cover at the top of the refrigerator. Lift the hook (not visible), located at the bottom of the front side of the cover with a flat-head screwdriver. 3 Pull out the water supply lines g. Disconnect all the wire harnesses h. Unscrew the ground wire i. Removing the Freezer Door 1 The water supply is connected to the upper right part of the rear surface of the refrigerator.
INSTALLATION 15 ENGLISH Removing the Refrigerator Door 1 2 Detach all the wire harnesses a. Unscrew the ground wire b. 4 Place the door, inside facing up, on a nonscratching surface. Assembling the Refrigerator Door 1 Place the door onto the bottom hinge pin a. 2 Fit the hinge b over the hinge lever latch c and slot it into place. Rotate the lever d counterclockwise to secure the hinge. Rotate the hinge lever c clockwise. Lift the top hinge d free of the hinge lever latch e.
16 INSTALLATION 4 NOTE depending on the model. Push the water supply lines into the hole on the top case and pull them through the backplate. Assembling the Freezer Door 1 Install the freezer door onto the bottom hinge pin a. NOTE depending on the model. 5 2 Fit the hinge b over the hinge lever latch c and slot it into place. Rotate the lever d clockwise and fasten the hinge. Hold the water supply connection and gently push in the collet e to connect the water supply lines as shown.
INSTALLATION 17 d insert the tube until only one line shows on the tube. Water Pressure You will need a cold water supply. Models with water filter: - 20 - 120 psi (138 - 827 kPa) Where reverse osmosis water filtration system is connected to a cold water supply: Assembling the Hinge Cover Position the hinge cover in its place. Insert and tighten the cover screws. - 40 - 60 psi minimum to reverse osmosis system (2.8 kgf/cm2 - 4.
18 INSTALLATION tubing to the shutoff valve and the refrigerator water valve. 2 Choose the valve location. accessible. It is best to connect into the side of a vertical water pipe. When it is necessary to connect into a horizontal water pipe, make the connection to the top or side, rather than at the bottom, to avoid drawing off any sediment from the water pipe.
INSTALLATION 19 diameter) to allow the refrigerator to move out from the wall after installation. Connect the tubing to the valve. (sleeve) for copper tubing onto the end of the tubing and connect it to the shutoff valve. Make sure the tubing is fully inserted into the valve. Tighten the compression nut securely. a Pipe Clamp b Saddle-Type Shutoff Valve c Vertical Cold Water Pipe 5 Tighten the pipe clamp. washer begins to swell. NOTE a Saddle-Type Shutoff Valve the tubing.
20 INSTALLATION doors do not close easily, tilt using the instructions below: NOTE copper tubing into the connection as far as possible. While holding the tubing, tighten the fitting. 1 Turn the leveling leg to the left to raise that side of the refrigerator or to the right to lower it. It may take several turns of the leveling leg to adjust the tilt of the refrigerator. a Tubing Clamp b ¼ in. Tubing c ¼ in. Compression Nut NOTE d Ferrule (sleeve) wrench will suffice. Do not over-tighten.
INSTALLATION 21 Start the Icemaker ted, turn icemakers on. 2 Use the wrench to adjust the height by turning the adjustment hinge pin to the right to raise the door or to the left to lower it. 3 Use the wrench to fasten the keeper nut by turning it to the right. CAUTION The hinge pin can be pulled out and the adjustable range of height is a maximum of 2 in. (5 cm). Turning on the Power cord into a 3-prong grounded outlet and push the refrigerator into the final position.