website http://www.lgservice.com LG LG Room Air Conditioner OWNER'S MANUAL MODELS: SV1 Chassis Prior to installation, this airconditioning unit must be submitted for approval by the utility service which provides electricity (EN 61000-2, EN 61000-3 Norm). IMPORTANT ? ? Please read this owner's manual and before air conditioner. installing and carefully operating your room thoroughly Please retain this owner's manual for future reference after reading it thoroughly.
Room Air Conditioner Owner's Manual TABLE OF CONTENTS FOR YOUR RECORDS Safety Precautions.........................3 Write the model and serial numbers here: Model # Prior to Operation ..........................8 Serial # You find them can on a label on the side of each unit. Dealer's Name Introduction ....................................9 Date Purchased Staple your receipt to this page in the event you need purchase or for warranty issues.
Safety Safety To Precautions Precautions prevent the injury of the user or other people and property damage, the following instructions must be followed. Incorrect by the The operation due to ignoring following indications. meanings of the instruction will cause harm or damage.
Precautions Safety Always install breaker and switching a air an board. No installation may cause and electrical shock. ? Do not leakage dedicated a fire ? keep conditioner. a Otherwise, it may the failure of cause a Do not install the or It will ? cause a fire or place that ther of falling down. a electrical ? shock. not fire ? product. Wax Do not disassemble installation an frame of the outdoor unit is or repair the product randomly.
Safety Take the power plug out if Do not necessary, holding the head of the plug and do not touch near use the the power cord tools. Precautions Do not open the suction inlet of the indoor/outdoor heating unit during operation. it with wet hands. ?Otherwise,itmaycauseafire or ? electrical shock. cause a fire ? and electrical shock. Do not allow water to into electrical Otherwise, it may shock and failure. Hold the run when parts.
Safety Precautions When the always product Otherwise, it may ? is submerged into water, Take contact the service center. cause a fire or care so that children may not step on the outdoor unit. electrical shock. ? Otherwise, children may be seriously injured due to falling down. Installation Install the drain hose to can be securely Otherwise, it may ? ensure that drain Install the done.
Safety Precautions Operation Avoid excessive and perform Use cooling ventilation not sometimes. ? a soft cloth to clean. Do use wax, thinner, When gas leaks, open the window for ventilation or a before strong detergent. Otherwise, it may do harm to ? your health. The appearance of the air conditioner may deteriorate, change color, or ? operating Otherwise, it may explosion, and a the unit. cause ENGLISH fire. develop surface flaws.
Prior to Operation Prior to for Preparing 1. Contact 2. 3. Use an Operation installation in the power Plug Operation specialist for plug properly. installation. dedicated circuit. a 4. Do not use an extension cord. 5. Do not 6. If the start/stop operation by plugging/unplugging the power cord. cord/plug is damaged, replace it with only an authorized replacement part. Usage 1. a long time may be hazardous to your health. Do not expose plants to direct airflow for a long time.
Introduction Introduction Symbols used in this Manual This symbol This symbol alerts you to hazards that may air conditioner. This NOTICE symbol ENGLISH alerts you to the risk of electric shock. indicates special cause harm to the notes. Features WARNING: This regulations. appliance should be installed in accordance with national wiring guide acts as a guide to help to explain product features.
Electrical Safety Electrical Safety WARNING: This To minimize the risk of electric appliance shock, you must must be properly grounded. alway plug into a grounded oulet. Preferred method Ensure proper ground exists before use WARNING: Do not cut power or remove the grounding prong from the plug.
Electrical Temporary Use of an Safety Adapter We strongly discourage the use of an adapter due to potential safety hazards. For temporary use only a UL-listed adapter, available from most local hardware stores. Ensure that the large slot in the adapter is aligned with the large slot in the receptacle for a proper polarity connection. To disconnect the power cord from the adapter, use one hand on each to avoid damaging the ground terminal.
Operating Instructions Instructions Operating How to insert the Batteries 1. Remove the battery cover by pulling it according to the arrow direction. 2. Insert new installed batteries making sure that the (+) and (-) of battery are correctly. 3. Reattach the NOTICE cover Use 2 by sliding it back into position. AAA(1.5volt) batteries. use rechargeable batteries. Do not Storage ? and Tips for using the Remote Controller The remote controller may be stored itonawall.
Operating Remote Control The controls will look like the Instructions Operations following. Controls Signal transmitter ENGLISH 1. START/STOP BUTTON Operation starts when this button is pressed and stops when the button is pressed again. 2. OPERATION MODE SELECTION BUTTON Used to select the operation mode. 3. ROOM TEMPERATURE SETTING BUTTONS Used to select the room temperature. 4. INDOOR FAN SPEED SELECTOR Used to select fan speed in four steps low, medium, high and CHAOS. 5 5.
Operating Instructions Cooling operation 1 Press the a 2 Start/Stop button. respond with The unit will beep. Open the door of the remote controller. To select Cooling Operation, press the Operation Mode Selection button. Each time the button is pressed, the operation mode is shiftedinthedirectionofthearrow. Auto Cooling Healthy Dehumidification 3 Close the door of the remote controller.
Operating Auto operation (Cooling model 1 only) Press the ENGLISH Start/Stop button. respond with The unit will a 2 Instructions beep. Open the door of the remote controller. To select Auto Operation, press the operation mode selection button. Each time the button is pressed, the operation mode is shiftedinthedirectionofthearrow.
Operating Auto Instructions changeover operation(Heat 1 Press the Start/Stop button. respond with beep. Open the door of the remote controller. To select Auto Changeover Operation, press the Operation Mode Selection button. Each time the button is pressed, the operation mode is shifted in the direction of the arrow. Cooling 3 only) The unit will a 2 pump model Auto Healthy changeover Dehumidification Heating (Heat pump model only) Close the door of the remote controller.
Operating Instructions Healthy dehumidification operation Press the 1 ENGLISH Start/Stop button. respond with The unit will a beep. Open 2 the door of the remote controller. To select Dehumidification Operation, press the Healthy Operation Mode Selection button. Each time the button is pressed, the operation mode is shiftedinthedirectionofthearrow.
Operating Instructions Heating operation (Heat pump model 1 Press the Start/Stop button. respond with The unit will a 2 only) beep. Open the door of the remote controller. To select Heating Operation, press the Operation Mode Selection button. Eachtimethebuttonispressed,theoperationmodeis shiftedinthedirectionofthearrow. Auto Cooling 3 Healthy Dehumidification Heating (Heat pump model only) Close the door of the remote controller. Set the The temperature higher than the room temperature.
Operating Jet cool Instructions operation 1 Press the a 2 beep. Press the Jet Cool button to the speed cooling will on 3 ENGLISH Start/Stop button. respond with The unit will operate mode and the unit at super high fan speed mode for 30 minutes. operate cooling To cancel the Jet Cool fan speed button again and the unit mode, press the Jet Cool button, the room temperature setting button will operate at high fan speed on cooling the or mode.
Operating Instructions Jet heat operation (Optional) Press the 1 Start/Stop button. respond with The unit will a beep. Open 2 the door of the remote controller. To select Heating Operation. Auto Cooling Healthy Dehumidification changeover Press the Jet Heat button to 3 speed heating Heating (Heat pump model only) operate the mode and the unit will at super high fan mode for 60 minutes.
Operating NANO PLASMA Instructions purification operation(Optional) 1 Press the Start/Stop button. Theunitwillrespondwitha beep. 2 Open ENGLISH the door of the remote controller. Press the NANO PLASMA button. Operation will start when the button is pressed and stop when the button is pressed again. 3 Set the fan speed again controller closed. You with the door of the remote can select the fan speed in four steps-low, medium, high or CHAOS.
Operating Instructions 2nd F operation 1 Press the a 2 Start/Stop button. respond with The unit will beep. Open the door of the remote control and press the 2nd operate functions printed in blue unter Function button to buttons. (Check the indication remote controller.
Instructions Operating Additional Features Sleep mode 1.PresstheSleepModeAutobuttontosetthetimeyouwanttheunittostopautomatically. 2. The Timer is sleep in one-hour increments programmed by pressing the Sleep Mode Auto button 1 to 7 times. The period in steps of 1 hour, press the Sleep Mode mode is available for 1 to 7 times. To alter the time Button while aiming at air conditioner. Sleep Mode Auto LED lights up. cancel the Sleep Mode, press the sleep Mode ) disappears from the operation display.
Operating Instructions Airflow direction control The up/down and right/left using the remote control. airflow be can Press Chaos adjusted by Swing Press the button 30 Press the button to start the unit. Start/Stop button and the louvers will and the louvers will again minutes, the louvers swing. stop. After return to the maximum airflow position automatically. Air circulation mode Circulates the 1. Press the 2. Open room air without Start/Stop the door cooling or heating.
Operating Forced Instructions operation Operation procedures when the remote control can't be used. operation will be started if the power button is pressed. If you want to stop operation, re-press the button. ENGLISH The Power button Cooling Model Operating mode Indoor FAN Speed Test operation During the TEST Room Temp.
Maintenance and Service Maintenance and Service Indoor Unit WARNING: Turn the Do not NOTICE use Supply bleach system off before cleaning. To clean, wipe with or a soft, dry cloth. abrasives. power must be disconnected before cleaning the indoor unit. Air filter The air filters behind the front grill should be checked and cleaned every 2 weeks or more often if neccessary. 1. Pull up the front panel.
Maintenance and Service Cleaning ? Recomended 1. Lift the front Filter use period panel, : About 3 months hold it up and pull the Air filter. ENGLISH 2. Remove the Plasma Filters. WARNING: Don't touch the PLASMA Filter within 10 seconds after grille, it may cause opening the inlet electric shock. 3. Put the Plasma Filters into the neutral detergent for 1~2 hours and then raise them. 4. Insert the Plasma Filters after perfectly drying them in shade.
Maintenance and Service Common Problems and Solutions Before calling for service If you have problems with your air conditioner, read the following information and try to solve the problem. If you cannot find a solution, turn off the air conditioner and contact your dealer. Air conditioner does not operate 1. Ensure that the air conditioner is 2. Check the fuse or plugged into a proper outlet. circuit breaker. 3. Check whether the voltage is unusually high or low.
Maintenance and Service Troubleshooting The air conditioner may be Problem operating abnormally when: Possible Causes The air conditioner is What To Do ? unplugged. The fuse is blown/circuit breaker is ? sure the air conditioner is plug into the outlet. Check the house fuse/circuit breaker box and tripped. Air Make pushed completely replace the fuse or reset the breaker. conditioner does not start Power failure. ? If power failure occurs, turn the mode control to Off.
Memo 30 Room Air Conditioner
