Installation Guide

ManualsBrandsLG ManualsSlide-In Electric RangesLSE4611ST

INSTALLATION

Installation Overview

Please read the following installation instructions first after purchasing this product or transporting it to another

location.

Check and choose the

proper location

Plug in the power cord Engage the anti-tip device Test run

Install anti-tip device Level the range Connect electric range

Conduit

connection

plate

Black White Red

Terminal

block

240 V or 208 V

Product Specifications

The appearance and specifications listed in this manual may vary due to constant product improvements.

Oven Range Models LSE4613, LSE4611

Description Electric Slide In Oven Range

Electrical requirements

LSE4613 : 13.5 kW 120/240 VAC or 10.1 kW 120/208 VAC

LSE4611 : 12.6 kW 120/240 VAC or 9.5 kW 120/208 VAC

Exterior Dimensions

(W) x 37

(H) x 26

(D) (D with door closed)

75.7 cm (W) x 96 cm (H) x 67.3 cm (D) (D with door closed)

Height to cooking surface 36

(91.4 cm)

Net weight 176 lb (80.0 kg)

Total capacity Total cap.: 6.3 cu. ft.

Summary of content (10 pages)

PAGE 1
0 INSTALLATION INSTALLATION Installation Overview Please read the following installation instructions first after purchasing this product or transporting it to another location.
PAGE 2
INSTALLATION 11 If you did not receive an anti-tip bracket with your purchase, call 1-800-243-0000 (1-888-542-2623 in CANADA) to receive one at no cost. Warning Warning Tip - Over Hazard •• The information in this manual should be followed exactly. Failure to do so may result in fire, electrical shock, property damage, personal injury, or death. A child or adult can tip the range and be killed. Verify the anti-tip bracket has been installed.
PAGE 3
12 INSTALLATION Installing the Range Unpacking and Moving the Range CAUTION •• You should use two or more people to move and install the range. (Excessive Weight Hazard) Failure to do so can result in back or other injury. •• Do not use the door handles to push or pull the range during installation or when moving the range out for cleaning or service. Doing so can result in serious damage to the door of the range. Remove packing material, tape and any temporary labels from your range before using.
PAGE 4
INSTALLATION 13 ENGLISH Dimensions and Clearances NOTE Save for the use of the local electrical inspector. 24" (60.9 cm) 3" (7.6 cm) Acceptable electrical outlet area Normal counter top depth Counter 36" (91.4 cm) top height A Cabinet opening Wall 24" (60.9 cm) 36" (91.4 cm) 3" (7.6 cm) 25" (63.5 cm) Center 15" (38 cm) Cabinet 11" (28 cm) 6" (15.2 cm) 29.8" (75.7 cm) 4" (10 cm) 9" (23 cm) 2.5" (6.3 cm) 5" (13 cm) 4" (10 cm) 6" (15.2 cm) 9" (23 cm) 2.5" (6.3 cm) A = 30" (76.2 cm) For U.
PAGE 5
14 INSTALLATION Installing the Anti-tip Device Use a level to check your adjustments. Place the level diagonally on the oven rack, and check each direction for level. Warning Tip - Over Hazard First check direction . A child or adult can tip the range and be killed. Verify the anti-tip bracket has been installed. Ensure the anti-tip bracket is engaged when the range is moved. Do not operate the range without the anti-tip bracket in place.
PAGE 6
INSTALLATION 15 •• Allow 2 to 3 ft (61.0 cm to 91.4 cm) of slack in the line so that the range can be moved if servicing is ever necessary. •• The power supply cord and plug should not be modified. If it will not fit the outlet, have a proper outlet Installed by a qualified electrician. Use the cord/conduit connection plate to install the power cord or conduit. Leave the connection plate as installed for power cord installations.
PAGE 7
16 INSTALLATION 3-Wire Connection : Power Cord 4-Wire Connection : Power Cord Warning Warning •• The middle (neutral or ground) wire, which is white, of a 3-wire power cord or a 3-wire conduit has to be connected to the middle post of the main terminal block. The remaining two wires of the power cord or conduit have to be connected to the outside posts of the main terminal connection block. Failure to do so can result in electrical shock, severe personal injury or death.
PAGE 8
INSTALLATION 17 4-Wire Connection: Conduit Install the conduit as follows: Remove the conduit connection plate from the rear of the oven and rotate it. The conduit hole (11/8") must be used. First, prepare the conduit wires as shown below. 3-Wire Conduit connection plate 4-Wire or Ground wire Second, install the conduit strain relief. For conduit installations, purchase a strain relief and insert it in the 11/8 in. (2.8 cm) conduit hole.
PAGE 9
18 INSTALLATION Engaging the Anti-tip Device Optional Rear Filler •• Move the range close enough to the opening to plug into the receptacle. If the counter does not bridge the opening at the rear wall the rear filler kit, that is provided with the slide in range, will be needed. •• Slide the range into position ensuring that the back leg slides under the anti-tip bracket. The range should sit flush against the back wall when properly installed.
PAGE 10
INSTALLATION 19 Check if the range is properly installed and run a test cycle. 1 Before using the cooktop for the first time, clean it with a ceramic cooktop cleaner. This helps protect the top and makes cleanup easier. 2 Turn the oven mode knob to the Off position to start test. 3 Turn each knob to the Hi position to check that the surface heating elements are working properly.