Specification Sheet

LG DISHWASHERS
HOME APPLIANCES
QUICK INSTALL & CLEARANCES
For full installation directions/clearances please refer to
the corresponding User Manual and Installation Guide.
IMPORTANT
© 2018 LG Electronics USA, Inc. All rights reserved. "LG Life’s Good" is a registered trademark of LG Corp. All other product and brand names are trademarks or registered trademarks of their respective owners. Design, features and specifications are subject to
change without notice. Non-metric weights and measurements are approximate. Some features may require Internet access. Content and services may vary by product and are subject to change without notice. 7/17/18
DUCTING OPTIONSCABINET LAYOUT
DIMENSIONS
LG STUDIO
10 3/8″
1 3/16″
29
15/16
″, 35
7/16
″
10
5/8″
22
1/16″
5 5/16″
4"
1"
1"
6
"
STANDARD
min. ducted - 27″
min. recirc. - 31″
max. - 48″
18 7/16″
A
C
B
26″ min
.
34
″
max.
mi
nimum ducted (D)
minimum recirculating (E)
maximum (F)
36
″
minimum ducted (A
)
minim
um recirculating (B)
maximum (C)
• Tolerances: +1/16",
-0 (1.6 mm, -0),
unless otherwise stated.
NOTE
• The exhaust duct(s) and electrical wiring
can be connected from either the top or the back of the hood.
▲
! WARNING
• Observe all governing codes and ordinances during planning and installation.
Contact your local building department for further information.
• Use only duct work deemed acceptable by state, municipal and local codes.
▲
! WARNING
• To reduce the risk of
personal injury caused
by reaching over a hot
appliance, cabinet storage
space located directly above
the range should be avoided
Minimum Cabinet Width:
Standard
Duct Cover
Hood
Heights
minimum ducted (A) 27"
minimum recirculating (B) 31"
maximum (C) 48-1/2"
Ceiling
Heights
minimum ducted (D) 89" (7' 5")
minimum recirculating (E) 93" (7' 9")
maximum (F) 118" (9' 10")
•
A minimum of 6” round duct must be
• Always use rigid metal ducts only.
up to 50%.
• ALWAYS, when possible, reduce the
number of transitions and turns. If long
duct run is required, increase duct size
from 6” to 7” or 8”.
• If turns or transitions are required, install
as far away from hood duct output and
as far apart as possible.
• Minimum mount height between range
top to hood bottom should be no less
than 26”.
• Maximum mount height should be no higher than 34”.
• It is important to install the hood at the proper mounting height. Mounting the
• If available, also refer to the range manufacturer’s height clearance requirements
and recommended hood mounting height above range.
Roof Pitch w/
Flashing & Cap
(blower
housing)
ductless
recirculating
(blower
housing)
side wall cap
w/ gravity damper
(blower
housing)
side wall cap
w/ gravity damper
(blower
housing)
▲
! WARNING Fire Hazard
• NEVER exhaust air or terminate duct work into spaces between walls, crawl
spaces, ceiling, attics or garages.
• All exhaust must be ducted to the outside.
• Use metal ductwork only.
•
Silver Tape or Duct Tape.
LSHD3089BD / LSHD3689BD
LSHD3080ST/ LSHD3680ST
30"/36" Wall Mount Range Hood
30” DIMENSIONS
A Width 29 15/16"
B Height 48 1/2”
C Depth 22 1/16”
36” DIMENSIONS
A Width 35 7/16”
B Height 48 1/2”
C Depth 22 1/16”
POWER RATINGS
AC Power 120V, 4 Amps ,60Hz