Model: LSSB2791** Built in Side by Side Refrigerator Installation Guide
Contents 1. Precaution before installation ................................................................. 3 2. Product and cabinet dimension .............................................................. 4 3. Precaution when moving the product .................................................... 5 4. Cabinet diagram and maximum door opening ....................................... 5 5. Refrigerator/Freezer door opening and how to fix at 90 degrees ............. 6 6.
1. Precaution before installation WARNING TIP-OVER HAZARD Use two or more people to move and install the refrigerator. To prevent the refrigerator from tipping over, install anti-tip brackets (provided). Failure to follow the refrigerator installation instructions can result in serious injury or death. Precaution ■ Install the product away from the heat of the heater, boiler or direct sunlight. Install the product where air flows well and is well ventilated.
2.
3. Precaution when moving the product ■. Before moving the refrigerator, check the line of movement to the location to install. (Refer to the product dimension and rotating radius.) 1) Request the installation to the specialized technician. It can cause electric shock, fire, malfunction and explosion. 2) Due to the characteristics of the built-in product, the top is heavy and can easily fall over when not installed. Therefore be careful when moving the product.
5. Refrigerator/Freezer door opening and how to fix at 90 degrees Push and install the device to keep the refrigerator door open and fixed, included in the accessory box, to the hole marked on the picture completely. The left and right side are installed in the same method. ※ If the device to keep the refrigerator door open and fixed cannot be inserted, move the refrigerator door slowly in left and right direction to push it in. 6.
6. Installation of part to prevent the product from falling over 1) Check if all the described parts are included in the accessory box. 2) Based on the recommended dimension on the picture, place the part to prevent the product from falling over. (Same for both left and right side) 3) Use the M4*L12 screw included in the accessory box to tighten 3 locations respectively on left and right side. (Tighten the screws completely so that the part is not loose from the cabinet.
7. Connecting power and securing space for water supply pipe (Unit : In) -. Power connection The location of the 115V 60Hz power connector must be located on the rear side of the product as shown in the picture.
8. How to install the water supply pipe ※ Check the location and installation detail of the water service pipe on the previous page before connecting the water supply pipe. Before inserting the product completely into the cabinet, check if there is any water leakage. 1) Disassemble the bottom grill. (Both the left and right sides are disassembled and reassembled in the same method.) - Use the (+) driver to disassemble the bottom grill.
9. Product detail dimension 41”( 1,04 1mm ) Total height of product 83-1/2” (2,121mm) 83-1/2” (2,121mm) Product height excluding front air inlet 82-1/2” (2,098mm) 82-1/2” (2,098mm) nt to m fro t o r f c h Dept of produ k c a b Front width (Including wing) 42”(1,067mm) /8” 25-3 mm) (645 mm) 04.
10. Cabinet detail dimension Cabinet detail dimension 5/32”(4mm) Product height 83-1/2”(2,121mm) Cabinet height 83-3/4” (2,127mm) Handle height 34-13/16” (884mm) Height of bottom part 3” (77mm) Cabinet depth 24”(610mm) Handle projection 2-5/16”(59.
11. How to adjust the height of the refrigerator and freezer door 1) If the height of the refrigerator and freezer is different, turn the bottom door height adjustment bolt to adjust the height. - The refrigerator and freezer door can be adjusted by 1/8”(3mm) respectively. - M6 wrench to adjust the height of the door is not included in the accessory box. (For accurate height adjustment, it is recommended to contact the service center.
12. How to adjust the height of the product 1) Use the height adjuster on the front/rear side to level the product and adjust the height on both left and right side. ※ For built-in product, adjust the height of and level the product during the initial installation. (For accurate height adjustment, it is recommended to contact the service center.) 2) Adjustment order (Adjustment method is same for both left and right side.) -. Disassemble the bottom grill using the (+) driver. -.
13. How to disassemble/reassemble the top grill 1) To adjust the left/right door, the top grill must be disassembled first. ※ Because the corners can be sharp, make sure to be careful during the task. ※ After disassembling the top grill, place it at a safe location to avoid any scratch on the panel. 2) Top grill disassembly and reassembly order -. Loosen the indicated screws and keep them safely. (Left and right are symmetrical) 2 -.
14. Left/Right door adjuster for refrigerator and freezer 1) The gap between the refrigerator and freezer is 5/16”(8mm) by factory default. If the gap between the refrigerator and freezer door changes during the product installation, use the left/right door adjuster to maintain the gap. - The refrigerator and freezer door can be adjusted by 5/32”(3.9mm) respectively. - M10 spanner for left/right adjustment is not included in the accessory box.
14. Left/Right door adjuster for refrigerator and freezer 2) Adjustment order ▶ Refrigerator door left/right adjuster Can be adjusted by 5/32”(3.9mm) Can be adjusted by 5/32”(3.9mm) Refrigerator left/right door adjuster -. Loosen 2 screws on part A and move to part B to assemble about 3/8”(10mm). -. Loosen the bolt of part C by 3/8”(10mm). -. Use the M10 spanner to adjust the Freezer left/right for part D. ※ When part D is rotated 2 times, the Freezer door must move by 1/32”(1mm).
P/No.
