OWNER’S MANUAL EZ SLIM WALL MOUNT Please read this manual carefully before installation and retain it for future reference. LSW600B P/NO : MFL63640525 (1207-REV00) www.lg.
Accessories Wall mount anchor 8 units Safety clip 2 units Wall mount screw Guide spacer 4 units 8 units Guide space screw 4 units (M8X25 mm) Set protection cushion 4 units User manual IMPORTANT SAFETY INSTRUCTIONS Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Warning This wall mount should be installed by a trained and experienced installer designated by the retailer. Do not install the product where the weight cannot be supported.
ENGLISH Caution Install the product according to the directions in the user manual. If the product is not installed based on the directions in the user manual, it can cause a serious injury or damage to the product. When installing the product or adjusting the height of the product after installing, always do so with 2 people. Working alone can cause the product to fall off and result in injury or damage to the product.
Installation method - Tools you will need : Phillips head "+" driver(Manual or motorized) Ø4 mm drill bit for wood or steel / Level / Stud finder / Drill. You may also need an 8 mm socket wrench or an Ø8 mm drill bit for concrete. 1 Fixating the mounting bracket on the TV - I f the screw will not fully tighten when using a guide spacer, recheck the assembly depth of the screw and refer to the technical service manual. Guide spacer Guide spacer screw 1.
How to attach to masonry walls - Use the anchors for wall material of concrete, light concrete, strong natural stone, soft natural stone masonry brick and hallow block that do not crack. Please follow the below direction. - Check the material of the wall and the thickness of the finishing. - When installing the product on wall material not designated, install the product so that each fixated location can withstand the pull out load of 70 kgf (686 N) and shear load of 100 kgf (980 N) or above.
4 How to assemble the wall mount support and display - Always install the display with 2 or more people. Safety clip 1. Set the display with the guide spacer assembled on the wall mount bracket on the wall in arrow direction. At this time, align the bottom assembly part and lift the set up lightly to align the top part. 2. When adjusting the horizontal level, use the safety ring provided by pressing it slightly to in the direction as illustrated.
ENGLISH 6 Tilt Angle Adjustment - The tilt angle can be adjusted after installation and setup. - When you adjust the angle, hold the product carefully with both hands to avoid any damage to the product or wall. ➊ ➋ ➍ ➌ ➊ ➋ ➌ ➍ 12° ± 2° 10° ± 2° 10° ± 2° 12° ± 2° < Set Side > < Set Top > * The above numbers are the maximum allowed, some models may do less. → Use both hands when adjusting the angles.
7 How to adjust height + 80 mm + 80 mm Clamping bolt - 80 mm - 80 mm → It is possible to move the set upward and downward by as much as 80 mm. → Please use both hands when adjusting the set upward and downward. Do not forget to remove the bolts on both sides of the set before adjusting the height. Anchor the bolts again after height adjustment. → Use 14~55 kgf of power when adjusting the set upward or downward.
ENGLISH 8 How to adhere the protection cushions and arrange cables → Use the protection cushions to reduce shock between the wall and TV/Monitor. → Arrange the cable like shown. You can purchase the cable holder separately or use it provided like accessory of the TV/Monitor get. Dimension [ unit : mm ] 600 Min. 25 465 400 81 210 238 81 45 Max. 214 25 25 25 25 25 25 25 25 25 25 20 530 658 Model LSW600B Width (mm) 658 Height (mm) 465 Depth (mm) 25 Weight (kg) 6.
The model and serial number of the product is located on the back or one side of the product. Record it below should you ever need service. MODEL SERIAL Supported Displays: (Please contract the retailers or refer to the TV owner’s manual for applicable models.