ENGLISH ESPAÑOL INSTALLATION MANUAL ELECTRIC CONVECTION BUILT-IN OVEN Please read these instructions thoroughly before installing and operating the oven. LSWS305ST LSWD305ST www.lg.
Part 1 SAFETY 1 BEFORE YOU BEGIN Remove all tape and packing materials before using the oven. Dispose all plastic bags after unpacking the oven. Never allow children to play with packing materials. You can download an Installation manual at http://www.lg.com.
Part 1 SAFETY This installation must be completed by a qualified installer or technician. • Please read the entire Installation Instructions prior to installation. • Remove all packing materials from the oven compartments before connecting the electrical supply to the oven. • Installer: please retain these instructions for local inspector’s reference, then leave them with the consumer.
Part 2 INSTALLATION REQUIREMENTS 1 INSTALLATION DRAWINGS (FOR 30” SINGLE BUILT- IN OVEN) The first step of your installation should be to measure your current cutout dimensions and compare them to the cutout dimensions shown below. You may find little or no cabinet work will be necessary. IMPORTANT NOTE • The cabinet base platform must be able to support 190lbs (86Kg).
Part 2 INSTALLATION REQUIREMENTS The first step of your installation should be to measure your current cutout dimensions and compare them to the cutout dimensions shown below. You may find little or no cabinet work will be necessary. IMPORTANT NOTE • The cabinet base platform must be able to support 325lbs (147Kg). If the cabinet does not have a solid bottom, two braces or runners must be installed level with the bottom of the cutout to support the weight of the oven.
Part 2 INSTALLATION REQUIREMENTS 3 INSTALLATION DRAWINGS (FOR 30” SINGLE BUILT- IN OVEN UNDERCOUNTER) The first step of your installation should be to measure your current cutout dimensions and compare them to the cutout dimensions shown below. You may find little or no cabinet work will be necessary. IMPORTANT NOTE • The cabinet base platform must be able to support 190lbs (86Kg).
Part 2 INSTALLATION REQUIREMENTS The second step of your installation should be to remove any packing material from the oven before you install the oven. 1. Remove all tape from around the oven. 2. Open the oven door and remove packaging materials and oven racks inside the oven. 3. Door removal is not a requirement for installation of the oven, but is an added convenience. To remove the door, follow the steps below. Step. 1 Step. 3 Fully open the door. Slot Step.
Part 3 ELECTRICAL CONNECTIONS 1 ELECTRICAL CONNECTION REQUIREMENTS The third step of your installation should be to follow electrical connection requirements below. Dedicated circuit protection must be prepared as recommended in electrical connection requirements and the oven should be grounded properly. IMPORTANT NOTE Be sure your wall oven is installed and grounded properly by a qualified installer or service technician.
Part 3 ELECTRICAL CONNECTIONS The fourth step of your installation should be to prepare the electrical connection as follows: 1. Turn off the circuit breaker or remove fuses to the oven branch circuit. 2. With the oven positioned directly in front of the cabinet opening, connect the flexible conduit to the electrical junction box as shown below. Position the conduit in such a manner that it will lie on top of the oven in a natural loop when the oven is installed.
Part 3 ELECTRICAL CONNECTIONS IMPORTANT NOTE • You will need to purchase an appropriate conduit connector to complete the connection of the conduit to the junction box. 3-wire circuit connection 4-wire circuit connection To connect to a three-wire circuit, follow these steps: To connect to a four-wire circuit, follow these steps: 1. Connect the oven ground (green) wire and neutral (white) wire to the branch circuit neutral (white or gray in color) wire, using a wire nut. 2.
Part 4 INSTALL THE OVEN ENGLISH 1 CABINET INSTALLATION The fifth step of your installation should be to install the oven into the cabinet as follows: 1. Sliding the oven into the opening. a. Loop (do not tie) a 36” (91cm) string around the conduit before the oven is slid into place.This will keep the conduit from falling behind the oven. b. Lift oven into cabinet cutout using the oven opening as a grip. Carefully push against the oven front frame. Do not push against outside edges. c.
Part 5 OPERATION CHECKLIST 1 CHECKING OPERATION Each of the functions has been factory checked before shipping. However, it is suggested that you verify the operation of the oven once more. Refer to the Owner’s Manual. Follow the instructions for the basic check. 1. Turn on power supply. The initial signal sound will be heard and LG logo should be appear in the display. 2. Check the operation of the broil mode. When the oven is set to broil, the upper element in the oven should become red.
Printed in Korea
