'sustain book. book Page 12 Friday, July 8, 2022 1:22PM 12 INSTALLATION el] INSTALLATION Before Installing Tools Needed dies Phillips screwdriver © Flat-blade screwdriver © Pencil and ruler @ Open-end or adjustable wrench @ Pipe wrench (2) (one for support) © Level Parts Parts You May Need Gas line shut-off valve Pipe joint sealant that resists action of natural and LP gases Flexible metal appliance connector (3/4" or 1/2" NPT x 1/2" 1D.
| ® 'sustain book. book Page 13 Friday, July 8, 2022 1:22PM | ® INSTALLATION 13 Choosing the Proper Location Dimensions and Clearances * Provide proper clearance between the range and adjacent combustible surfaces. +» These dimensions must be met for safe use of your range. + The location of the electrical outlet and pipe opening (see "Gas Pipe and Electrical Outlet Locations" below) may be adjusted to meet specific requirements. + The range may be placed with 0" clearance (flush) at the back wall.
® | ® 'sustain book. book Page 14 Friday, July 8, 2022 1:22PM el] 14 INSTALLATION Clearances ails hb of @ IRs Minimum distance from top of range to combustible surface | 30" (76.2 cm) overhead eo Minimum clearance to left/right wall 5" (12.7 cm) ® Maxim urn depth for cabinets above counter tops 13" (33.0 cm) o Front edge of the range side panel forward from cabinet 21/4" (6.3 cm) 9 To cabinets below cook top and at the range back 0" ® Minimum opening In overhead cabinets 30" (76.
ov | ® 'sustain book. book Page 15 Friday, July 8, 2022 1:22PM | ® INSTALLATION 15 Flooring Your range, like many other household units, is heavy and can be installed on soft floor coverings such as cushioned vinyl or carpeting. Use care when moving the range on this type of flooring. When the floor covering ends at the front of the range, the area that the range will be installed on should be built up with plywood to the same level or higher than the floor covering.
'sustain book. book Page 16 Friday, July 8, 2022 1:22PM 16 INSTALLATION | ® Connecting the Range to Gas 4), WARNING Isolate the range from the gas supply system by closing its individual shut-off valve during any pressure testing of the gas supply system at test pressures equal to or less than 1/2 psi (3.5 kappa. The appliance and Its individual shut-off valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2 psi (3.5 kappa.
© | ® 'sustain book. book Page 17 Friday, July 8, 2022 1:22PM el] INSTALLATION 17 © 1/2" adapter @ Gas flow Into range @ Flex connector (6 ft. max.) @ Gas shut-off valve @ 1/2" adapter @ 1/2" or 3/4" gas pipe Pressure Regulator Position © Pressure regulator Adjusting Alr Shutters (for LP Conversions) The range comes from the factory with the air shutters adjusted for proper air flow for natural gas.
[o— | ® 'sustain book. book Page 18 Friday, July 8, 2022 1:22PM 18 INSTALLATION el] Surface Burners Assembling the Surface Burners 4), CAUTION * Do not operate the burners without all parts in place. 1 Place the burner caps and heads on the cook top. « There is one small, one medium, one large, one oval (center), and one extra large burner head and cap. 2 Make sure that the caps and heads are placed In the correct locations. 3 Make sure that the hole In the burner head is positioned over the electrode.
'sustain book. book Page 19 Friday, July 8, 2022 1:22PM | ® INSTALLATION 18 4 Insert a small, flat-blade screwdriver Into the opening marked below, © simmer on dual burner @ simmer on other burners 5 Turn the screw to adjust the flame. * Hold the valve shaft with one hand while turning the screw to adjust with the other. [] Replace the knob, 7 Test the flame stability. * Test 1: Turn the knob from Hi to Le quickly. If the flame goes out, increase the flame size and test again.
| ® 'sustain book. book Page 20 Friday, July 8, 2022 1:22PM 20 INSTALLATION 4b WARNING Engage the range to the natl-tip device by following the guide on the anti-tip bracket template. Ensure the anti-tip device is reengaged when the range Is moved by following the guide on the anti-tip bracket template. Re-engage the anti-tip device if the range is moved. Do not operate the range without the anti-tip device in place and engaged. See installation instructions for details.
| ® Sustain book book Page 21 Friday, July 8, 2022 1:22 PM wy] ® INSTALLATION 21 ¢ 1 Remove all packing materials from Inside the oven cavity, | 2 Turn oven mode knob to select Broil. HI appears in the display. * Make sure the door is closed. HEIDI | 3 Press Start. TT ER, NOTE + It may take between 30 and 90 seconds for the burner to start heating.
