Operating Instructions LVC-A730NP (PAL, Normal) LVC-A730HP (PAL, High) LVC-A730NM (NTSC, Normal) LVC-A730HM (NTSC, High) Before installing and using the camera, please read these instructions thoroughly and retain them for later reference.
Warning CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
Contents Features...................................................................................................................................3 Cautions for Safe Operation .....................................................................................................4 Operating Controls and Their Functions..................................................................................5 Power IN/CONTROL ............................................................................................
Cautions for Safe Operation Power Supply This camera must always be operated a 12V DC UL Listed, Class 2 Power Supply only. Handling of the unit Be careful not to spill water or other liquids on the unit, or to get combustible or metallic material inside the body. If used with foreign matter inside, the camera is liable to fail, or to be a cause of fire or electric shock.
Operating Controls and Their Functions 1 3 4 TELE 6 5 7 2 8 S-VIDEO OUT WIDE F.NEAR F.FAR MENU POWER IN CLASS 2 ONLY CONTROL 9 VIDEO 10 LVC-A730 Control names and Functions 1. Tripod adaptor This adaptor can also be attached on the bottom of the camera. 2. Lens mount cap 3. When push the TELE KEY, picture is telephoto 4. When push the WIDE KEY, picture is wide angle 5. Focus Near Key In a manual situation, focus get near. 6. Focus Far Key In a manual situation, focus get far. 7.
POWER IN/CONTROL You can adjust focus and zoom by a pin terminal on the back side of the camera. 1 6 2 5 3 4 PIN NO. Description Color * 1 2 3 4 5 6 RXD TXD External Key input (A/D IN) NC. GND Power input (DC 12V) Green White Brown(Blue) Yelllow Black Red * is the color of the cable.(If it is offered) 3 A/D IN 6.8K 0.01µ 6 POWER ON/OFF 8.
Setting The Menu MENU 1 INITIAL SET ON BACKLIGHT OFF COLOR ON NEGATIVE OFF FOCUS PUSH AUTO FLICKERLESS OFF WBC MODE AUTO • The On Screen Display menu can be used by MENU, TELE, WIDE, F.NEAR(F(+)), F.FAR(F(-)) Key. Menu 1 1. INITIAL SET Set the initial mode ON, the changed data are renewed. 2. BACKLIGHT In case of the excessive light is behind the center object, It is necessary to prevent the center object too darken. Turn the BACKLIGHT ON, then the center object became lighter. 3.
MENU 1 INITIAL SET ON BACKLIGHT OFF COLOR ON NEGATIVE OFF FOCUS PUSH AUTO FLICKERLESS OFF WBC MODE AUTO 4. NEGATIVE Use for changing NEGATIVE and POSITIVE mode. • ON: NEGATIVE mode, • OFF: POSITIVE mode 5. FOCUS AUTO/MAN: Set the focus mode to Auto or Manual. PUSH AUTO: Set the focus mode to Push Auto mode. 6. FLICKERLESS Set the FLICKER ON mode, then the flicker is removed.
7. WBC MODE • AUTO: WB Range 2800°K ~ 8000°K • SPECIAL(SWB): Under the special WB condition (Differ from curve of the control color temperature), Adjust Red and Blue to perform a desired Auto White Balance. WBC MODE SPECIAL RED ADJUST 2 BLUE ADJUST 253 RED ADJUST WBC MODE SPECIAL RED ADJUST 0 BLUE ADJUST 0 10 BLUE ADJUST 10 Set the WB mode is SPECIAL mode using F(+) or F (-) key code. The RED/BLUE ADJUST menu is appeared. Adjust the Red to a desired value by using F(+) or F (-) key code.
• MANUAL( MW ): Hue control adjustment is available manually. Adjust MWB CONTROL to a desired value. WBC MODE MWB CONTROL MANUAL 0 MWB CONTROL Set the WB mode is MANUAL mode using F(+) or F (-) key code. The MWB CONTROL menu is appeared. WBC MODE MWB CONTROL 0 Adjust the MWB CONTROL to a desired value. MANUAL 0 The whole MENU is displayed using TELE or WIDE key code. Moving another item of MENU is available. • PUSH AUTO(PWB): A regular environment or object was forced to do White Balance action.
Menu 2 MENU 2 CAMERA ID SHARPNESS BRIGHTNESS ZOOM START ZOOM END FOCUS FROM AE MODE OFF 10 42 x1 x128 1Cm AUTO 8. CAMERA ID To connect a large number of camera, It can be assigned to identification number to each camera control easily (OFF, 1~255 : total numbers of ID are 256). CAUTION: To transfer ID code of camera , set the ID number of camera in first, And then the ID number display continuously. 9. SHARPNESS Use to change the contour of scene (0~15). 10.
14. AE MODE In the situation is unadjustable exposure, AE mode support to make a fit exposure. • AUTO: Use to compensate the exposure automatically. • SHUTTER: Use to change the Shutter Speed control. In this time, AE mode act automatically (8 steps control is available). • IRIS: Use to change the value of Lens’s Iris (IRIS of lens is fixed manually, and the action of exposure compensation depend on its of AGC). AE MODE IRIS ADJUST IRIS 0 Set the AE mode to IRIS using F(+) or F (-) key code.
• MANUAL: Use to set the shutter speed, IRIS and AGC manually. AE MODE SHUTTER IRIS ADJUST AGC ADJUST MANUAL NORMAL 0 60 SHUTTER Set the AE mode is MANUAL mode using F(+) or F (-) key code. The SHUTTER, IRIS ADJUST, AGC ADJUST MENU is appeared. NORMAL Adjust the SHUTTER to a desired value. AE MODE SHUTTER IRIS ADJUST AGC ADJUST MANUAL NORMAL 10 80 The whole MENU is displayed using TELE or WIDE key code. Moving another item of MENU is available.
On-Screen Display Some of these functions will be displayed every time the camera is operated and then disappeared after 5 seconds. FUNCTION OSD Format Description 1 Focus Mode Non display Focus Auto Mode ☞ Focus Manual mode 2 Back Light Non display Back Light OFF Back Light ON 1 ☞ 2 3 4 6 Non display Normal Shutter (NTSC:1/60 PAL: 1/50) 1/125 8 variable steps.
On-Screen Display FUNCTION OSD Format Description 6 WBC Mode Non display White Balance AUTO SWB Special Auto White Balance; Adjustment Mode according to change of external illuminant. RED ADJUST and BLUE ADJUST (0~255) are available. After changing R/B value, the maintenance mode is “AUTO”.
Specifications Image device 1/4" interline transfer CCD NTSC, High resolution : 380,000 NTSC, Normal resolution : 250,000 PAL, High resolution : 440,000 PAL, Normal resolution : 290,000 Sync system Internal sync Horizontal resolution Approx.450 Line (NTSC, High resolution) 320 Line (NTSC, Normal resolution) 450 Line (PAL, High resolution) 320 Line (PAL, Normal resolution) (at center of screen) Lens x16 Optical Zoom(f=3.9~63mm, F1.6 - 2.
Specifications Power requirement 12V DC UL Listed, Class 2 Power Supply only Video output BNC-type, S-Video-type (1.0Vp-p, 75ohms) Power consumption Max 4.7w operating temperature -10oC ~ 50oC Operating Humidity 0%~80% Storage temperature -20oC to+60oC Dimensions 59.4mm(W) x 61.2mm(H) x 95mm(D) Specifications are subject to change without notice.
P/NO.
