Operating Instructions LVC-A910 LVC-A911 LVC-A912 LVC-A913 Before installing and using the camera, please read these instructions thoroughly and retain them for later reference.
Warning CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN To prevent fire or shock hazard,do not expose the unit to rain or moisture. To avoid electrical shock,do not open the cabinet. Refer servicing to qualified personnel only. Regulatory Notices For U.S.A CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER(OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Contents Features............................................................................................................................................................................3 Cautions for Safe Operation ............................................................................................................................................4 Operating Controls and Their Functions.................................................................................................................
Cautions for Safe Operation Power Supply This camera must always be operated a 12V DC power supply. Handling of the unit Be careful not to spill water or other liquids on the unit, or to get combustible or metallic material inside the body. If used with foreign matter inside, the camera is liable to fail, or to be a cause of fire or electric shock. Operating and storage location Avoid viewing a very bright object (such as light fittings) for an extended period.
Operating Controls and Their Functions 1. Tripod adaptor This adaptor can also be attached on the bottom of the camera. 2. Lens mount cap 3. TELE Key When push the TELE KEY, picture is telephoto 4. WIDE Key When push the WIDE KEY, picture is wide angle 5. Focus Near Key In a manual situation, focus get near. 6. Focus Far Key In a manual situation, focus get far. 7. Menu Key If you want to set up a diverse function, you can push this button. 8.
Power In / Control You can adjust focus and zoom by a pin terminal on the back side of the camera. * is the color of the cable.
Power In / Control 7
External Key (A/D IN) Schematic diagram of wired remote-control 8
MENU DESCRIPTIONS page 10 page 11-12 page 13-14 page 15-17 page 18-19 page 20 page 21 page 22 page 23 Using TELE, WIDE, FOCUS+, FOCUS- button • TELE and WIDE are used for UP and DOWN. • FOCUS+ and FOCUS- are used for INCREASE and DECREASE the data.
CAMERA ID 1. CAMERA ID To connect a large number of camera , It can be assigned to identification number to each camera for camera control easily. (OFF, 0 - 255 : total numbers of ID are 256) • It only can be set this function using ID commend. To transfer ID Code of camera , In first byte at PC control. Set the ID number of camera , and then the ID number display continuously.
FOCUS MODE SET 2. Focus Set: 2-1. Focus Mode Set : This function is for focus mode setting A) Set up "FOCUS SET" in main menu using Menu key. Select the "FOCUS MODE" in submenu using Tele/Wide key. And then set the mode (Auto, Push auto, or Manual) using Focus key. 2-2. Focus Distance Set : This function is for selection of minimum shooting distance. A) Select the "FOCUS DIST" in submenu using Tele/wide key. B) Set the focus distance mode from 1cm to 5M. (1cm, 10cm, 50cm, 1M, 3M, 5M) using Focus key. 2-3.
FOCUS MODE SET 2-4. ZOOM END Set : This function is for selection of zoom end position. A) Select the "ZOOM END" in submenu using Tele/wide key. B) Set the Zoom end mode from X(Zoom Start + 1) to x176 using Focus key. 2-5. ZOOM SPEED Set : This function is for selection of zoom speed. A) Select the "ZOOM SPEED" in submenu using Tele/wide key. B) Set the Zoom speed, Slow, Middle , Quick using Focus key. 2-6. ZOOM TRACKING MODE Set : This function is for selection of zoom tracking mode.
AWB SET 3. AWB SET 3-1. WB Mode Set : This function is for changing the WB mode. A) Set up "AWB SET" in main menu using Tele/wide key. B) Select the "WB MODE" in submenu using Tele/wide key. C) Set the mode Auto, Push auto , Manual, Outdoor, Indoor, Special using Focus key. *WBC MODE ; Use for changing White Balance Mode . 1) AUTO ; WB Range 2800 °K ~ 8000 °K . 2) PUSH AUTO ; Set the AWB mode to Push Auto, then WB Mode is auto.
AWB SET 3-3. BLUE ADJUST Set : This function is available for Special, Push Auto, Manual WB mode. This mode is the adjustment of user option for special color. A) Select the "BLUE ADJUST" in submenu using Tele/wide key. B) Adjust the level from (-30 to 30 SPECIAL, -128 to +127 PUSH AUTO, 0-255 MANUAL) using Focus key. 3-4. PUSH AUTO : In case of PUSH AUTO WB mode. Adjust the push auto mode ON, WB act automatically. 3-5.
AE SET 4. AE SET 4-1. AE Mode Set : This function is for changing to AE mode. A) Set up "AE SET" in main menu using Tele/wide key. B) Select the "AE MODE" in submenu using Tele/wide key. C) Set the mode auto, IRIS MAN, AGC MAN, Manual, Auto using Focus key. 4-2. IRIS ADJUST Set : This function is available for IRIS MAN mode. A) Select the "IRIS ADJUST" in submenu using Tele/wide key. B) Adjust the level from ##MIN to ##MAX(MANUAL, IRIS MAN) using Focus key. * ## : Current level at Auto mode. 4-3.
AE SET 4-4. BRIGHTNESS ADJUSTMENT Set : A) Select the "BRIGHTNESS" in submenu using Tele/wide key. B) Adjust the level from ##MIN to ##MAX. using Focus key. * ## : Current level at Auto mode. 4-5. BACKLIGHT Set : A) Select the "BACKLIGHT" in submenu using Tele/wide key. B) Set the mode OFF, ON, or AUTO using Focus key. * Auto BLC (Auto back light compensation) When a back light condition occurs in area1,area2, area3, or area4. the back light compensation is enable.
AE SET 4-7. SHUTTER SPEED Set : A) Select the "SHUTTER" in submenu using Tele/wide key. B) Set the mode NORMAL, 1/125 - 1/10000 using Focus key. 4-8. INITIAL SET : A) Select the "INITIAL SET" in submenu using Tele/wide Command, B) Set the initial set mode to ON or OFF using Focus key. 4-9. RETURN TO MAIN MENU : This function is exit to main menu. A) Select the "RETURN " in submenu using Tele/wide key. B) Set the return mode using Focus key.
SPECIAL SET 5. SPECIAL SET 5-1. User Title Set : This function is for custom title on screen display. A) Set "SPECIAL SET" in main menu using Tele/wide key. B) Select the"USER TITLE" in submenu using Tele/wide key. C) Set the position of title and set data using Tele / Wide, Focus key. 5-2. SHARPNESS ADJUST Set : A) Select the "SHARPNESS" in submenu using Tele/wide key. B) Adjust the level from 0 to 15 using Focus key. 5-3. MIRROR Set : A) Select the "MIRROR" in submenu using Tele/wide key.
SPECIAL SET 5-5. NEGATIVE Set : This mode is to change color and luminance to negative. A) Select the "COLOR" in submenu using Tele/wide key. B) Select the mode ON, OFF using Focus key. 5-6. WIDE BURST Set : This mode is to change color burst width for long distance application. A) Select the"WIDE BURST" in submenu using Tele/wide key. B) Select the mode ON, OFF using Focus key. 5-7.
MOTION DET 6. MOTION DETECTION SET 6-1. DETECTION Mode Set : A) Set "MOTION" in main menu using Tele/wide key. B) Select the "DETECTION" in submenu. Using Tele/wide key. C) Set the mode ON, OFF using Focus key. 6-2. LEVEL ADJUST Set : This function is available for DETECTION ON mode. A) Select the "LEVEL SET" in submenu. Using Tele/wide key. B) Adjust the level to some sensitivity using Focus key. 6-3.
F. OSD SET 7. F. OSD SET 7-1. FUNCTION Set : A) Set "F. OSD" in main menu using Tele/wide key. B) Select the mode what you want in submenu using Tele/wide key. C) Set the display mode of OSD using Tele / Wide, Near/Far key. *INITIAL SET and RETURN are the same as before procedure.
E. SENSITIVITY SET 8. E. SENSITIVITY SET: (option) 8-1. E. SENSITIVITY SET A) Select the "E.SENSITIVITY" in submenu using Tele/wide key. B) Select the sensitivity mode what you want in submenu using Focus key. * Mode sequence : OFF-X2 AUTO-X4 AUTO-X8 AUTOX10AUTO-X16 AUTO- X32 AUTO -OFF- X2 FIX-X4 FIX -X8 FIX -X10 FIX -X16 FIX - X32 FIX-OFF 8-2. INITIAL SET : If initial mode set to ON, E.SENSITITY functions are changed to the factory setting A) Select the "INITIAL SET" in submenu using Tele/wide key.
WDR SET 9. WDR SET (option) 9-1. WDR SET A) Select the "WDR" in main menu using Tele/wide key. B) Select the "WDR CONTROL" in submenu using Tele/wide key. C) Select the WDR mode what you want in submenu using Focus key. * Mode sequence : OFF -- ON -- AUTO * WDR Auto mode is working at the condition of high light back light. 9-2. LEVEL ADJUST Set : This function is the gain adjustment of WDR A) Select the "SENSITIVITY" in submenu using Tele/wide key. B) Adjust the level to some sensitivity using Focus key.
On Screen Display Some of these functions will be displayed every time the camera is operated and then disappeared after 5 seconds. FUNCTION OSD Format Description 1. Focus Mode Non display Auto Mode Manual / push Auto Mode 2. Back Light 3. Shutter Speed 1 2 3 Non display Back Light OFF "BL"display BLC ON / Auto BLC Mode Non display Normal Shutter (NTSC:1/60 PAL: 1/50) "Ff"display Flickerless Mode 6 1/125 1/10,000 4. CAMERA ID 5.
On Screen Display FUNCTION 6. STAND-BY OSD Format Description Indicate the camera stand-by during the camera’s power turning ON. 7. WBC Mode White Balance AUTO S W Special Auto White Balance; Adjustment Mode according to change of external illuminant. RED ADJUST and BLUE ADJUST (0~255) are available. After changing R/B value, The mainternance mode is “AUTO”. WBC Preset for INDOOR (3200°K) WBC Preset for OUTDOOR (5100°K) M W Manual WBC Adjustment; In manual mode the HUE control is available (0 ~ 99).
Specifications Image device 1/4" interline transfer CCD NTSC, High resolution : 811(H) X 508(V) 410K NTSC, Normal resolution :537(H) X 505(V) 270K PAL, High resolution : 795 (H) X 596 (V) 470K Sync system Internal sync Horizontal resolution Approx.480 Line (NTSC, High resolution) 320 Line (NTSC, Normal resolution) 480 Line (PAL, High resolution) 320 Line (PAL, Normal resolution) (at center of screen) Lens X 22 Zoom ( F 1.6 f = 3.9 ~ 85.
Specifications Focal Length OSD(On Screen Display) Power requirement 0.01m (WIDE), 1.0m (TELE) ON/ OFF DC 12V Video output Composite Output 75Ω Terminated / Y,C Separated Power consumption 5W operating temperature 0°C - 45°C Operating Humidity 0% RH - 60% RH Storage temperature -20°C - 60°C, 0% RH - 85% RH Dimensions 56.2mm(W) x 64mm(H) x 101mm(D) Weight 388g Specifications are subject to change without notice.
ݷᔫᒎฉ LVC-A910 LVC-A911 LVC-A912 LVC-A913 在您使用此摄像机之前,请完整阅读此操 作指南以供参考。
வস ᓖፀ 电击危险请勿打开 为了防止电击事故,请不要将该产品暴露在雨中或潮湿的环境中。 为了避免电击的危险,请不要打开机壳,如需维修,请联系专业维 修人员。 ਖࢾဉී 警告:为了减少电击的危险,请勿拆下前 盖(或后盖) 内部没有任何用户可以维修的零部件。 如需维修,请联系专业维修人员。 此符号用于警示用户,产品外壳存在 未绝缘的危险电压,会产生对人身造 成电击的危险。 U.S.
ഺ ᄂቶ....................................................................................................................................................................................3 ڔཝݷᔫᓖፀူሲ .............................................................................................................................................................4 ݷᔫ఼ᒜૺถ ..............................................................................................................................................
ڔཝݷᔫᓖፀူሲ ࢟Ꮞ 此摄像机必须始终使用 12V DC 电源 ۃᏥስ૦ 请注意不要将水或其它液体溅到摄像机内部 也不 要让可燃性物品或金属物品掉入摄像机内 如果摄 像机内部有杂质 则可能会导致摄像机故障或引发 火灾或电击 ဧਜ਼ࡀह࢛ 不要长时间观看过于明亮的物体 以下环境中使用或存放此设备 • • • • • 如灯具 避免在 过热或过冷的地方 工作温度 0°C-45°C) 潮湿或有灰尘的地方 有雨的地方 有强烈振动的地方 靠近有强电磁辐射的地方 如收音机或电视发射 机附近 4 ስ૦ۣዸ • 使用吹风机将表面的灰尘或脏物吹掉 • 请使用软布清洁机身 如果太脏 请使用带有少 量中性清洁剂的软布清洁 然后擦干 • 请不要使用挥发性溶剂 如稀释剂 酒精 苯和 杀虫剂 会损坏表面或机身
ݷᔫ఼ᒜૺถ 1. ྯ୭ଦᓞ 此转接器还可以安装到摄像机的底部 2. ᄿڔᓤঙ 3. TELE 当按 TELE KEY 时 图像为远距拍摄 4. WIDE 当按 WIDE KEY 时 图像为广角拍摄 5. ౯தୡ௦ 在手动操作时 将焦距拉近 6. ౯Ꮠୡ௦ 在手动操作时 将焦距拉远 7. ݩ 如果您要设置不同的功能 8. ၁ຫၒ߲ 可按此键 S-Video ቯ 连接到监视器的 S-Video 输入接口 9. ስ૦఼ᒜ JACK ా 12 ᑣ DIN JACK ቯ • 连接到外部电压控制器 • 您可以通过此接口为摄像机供电 10.
࢟Ꮞၒྜྷ0఼ᒜ 您可以通过摄像机背面的针形端子调节焦距和变焦。 * 为电缆颜色。(如果提供) 6
࢟Ꮞၒྜྷ0఼ᒜ 7
ᅪݝ (A/D IN) 线控示意图 镜像 8
ݩႁී ဧ TELE WIDE FOCUS+ FOCUS- • TELE 远摄 和 WIDE 广角 用于 UP 拉近 和 DOWN 拉远 • FOCUS+ 拉长焦距 和 FOCUS- 拉近减少 用于 INCREASE 增加 DECREASE 减少 数据 和 9
ስ૦ ID 1.
࣪ୡෝါᒙ 2. ࣪ୡᒙǖ 2-1. ࣪ୡෝါᒙǖ ࠥถ᎖ᒙ࣪ୡෝါ A) 使用菜单键在主菜单中设置 FOCUS SET 使用 然后使用 Tele/Wide 键选择子菜单中的 FOCUS MODE 对焦键设置模式 Auto(自动) Push auto(强制自动) Manual(手动)) 2-2. ࣪ୡ௦ಭᒙ ࠥถ᎖ኡᐋᔢቃ௦ಭ A) 使用 Tele/Wide 键选择子菜单中的 FOCUS DIST B) 使用对焦键在 1cm 到 5M 之间设置对焦距离模式 (1cm, 10cm, 50cm, 1M, 3M, 5M) 2-3.
࣪ୡෝါᒙ 2-4. ܤୡஉၦᒙ ࠥถ᎖ኡᐋܤୡஉၦᆡᒙă A) 使用 Tele/Wide 键选择子菜单中的 ZOOM END B) 使用对焦键在 变焦开始 + 1 x176 到 X 之间设置变焦结束模式 2-5. ܤୡႥࣞᒙ ࠥถ᎖ኡᐋܤୡႥࣞă A) 使用 Tele/Wide 键选择子菜单中的 ZOOM SPEED B) 使用对焦键设置变焦速度 Slow 低 Middle 中 2-6. ܤୡৌᔍෝါᒙ ࠥถ᎖ኡᐋܤୡৌᔍෝါ Quick 快 A) 使用 Tele/Wide 命令选择子菜单中的 ZTRK B) 将变焦跟踪模式设置为 Auto 自动 或 Manual 手动 * ܤୡৌᔍᒎୡܤୡᓨზă 2-7. ߱ဪᒙ ྙਫ߱ဪෝါᆐ ON ఎ ถۻখޣ߲ࡵܤᒙ Ⴥᎌ FOCUS SET ࣪ୡᒙ A) 使用 Tele/Wide 键选择子菜单中的 INITIAL SET B) 使用对焦键将初始模式设为 ON 或 OFF 2-8.
ᔈࣅڹຳੰᒙ 3. ᔈࣅڹຳੰᒙ 3-1. ڹຳੰෝါᒙ ࠥถ᎖ኀখڹຳੰෝါ A) 使用 Tele/Wide 键在主菜单中设置 AWB SET B) 使用 Tele/Wide 键选择子菜单中的 WB MODE C) 使用对焦键设置模式 Auto(自动) Push auto(强制自动) Manual(手动) Outdoor(室外) Indoor(室内) Special(特殊) *WBC MODE: ᎖ኀখڹຳੰෝါ 1) AUTO 白平衡范围 2800 °K ~ 8000 °K 2) PUSH AUTO 将 AWB 模式设为 Push Auto 强制自动 则白 平衡模式会自动调整 3) SPECIAL 在特殊的白平衡条件 不同于控制色温曲线 下 调 整红色和蓝色以达到所需的自动白平衡 3-2.
ᔈࣅڹຳੰᒙ 3-3. ౸ྻࢯᑳᒙ ࠥถభ᎖ Special Push Auto ࠥෝါဵ࣪ᄂၐዕྻઓኡሲࡼࢯᑳ Manual WB ෝါ A) 使用 Tele/Wide 键选择子菜单中的 BLUE ADJUST B) 使用对焦键调节值大小 -30 到 30 SPECIAL -128 到 +127 PUSH AUTO 0-255 MANUAL 3-4. PUSH AUTO ༓ᒜᔈࣅ Ᏼ PUSH AUTO WB ෝါሆ ༓ᒜᔈࣅෝါᆐ ON WB ્ᔈࣅᒊቲ 3-5. ߱ဪᒙ ྙਫ߱ဪෝါᆐ ON ఎ Ⴥᎌ AWB ᔈࣅڹຳੰ ถۻখޣ߲ࡵܤᒙ A) 使用 Tele/Wide 键选择子菜单中的 INITIAL SET B) 使用对焦键将初始模式设为 ON 或 OFF 3-6.
ᔈࣅੰᒙ 4. ᔈࣅੰᒙ 4-1. ᔈࣅੰෝါᒙ ࠥถ᎖ኀখᔈࣅੰෝါă A) 使用 Tele/Wide 键在主菜单中设置 AE SET B) 使用 Tele/Wide 键选择子菜单中的 AE MODE C) 使用对焦键设置模式为 ATUO IRIS MAN AGC MAN Manual 4-2. མࢯᑳᒙ ࠥถ᎖ IRIS MAN ෝါ A) 使用 Tele/Wide 键选择子菜单中的 IRIS ADJUST B) 使用对焦键在 ##MIN 到 ##MAX(MANUAL, IRIS MAN) 中调整设 置 * ## : 自动模式当前值。 4-3.
ᔈࣅੰᒙ 4-4. ೡࣞࢯᑳᒙ A) 使用 Tele/Wide 键选择子菜单中的 BRIGHTNESS B) 使用对焦键在 ##MIN 到 ##MAX 中调整设置 * ## : 自动模式当前值 4-5. ۳ᒙ A) 使用 Tele/Wide 键选择子菜单中的 BACKLIGHT B) 使用对焦键设置模式为 OFF ON 或 ATUO * ᔈࣅ BLC ᔈࣅ۳ޡݗ W当区域 1 区域 2 区域 3 或区域 4 中的背光满足条件时 可使用背光补偿 当此区域中的背光条件消失时 BLC 自动 停用 如果不需要此模式 将其设为 OFF 4-6. ᇄ࿑ႄᒙ A) 使用 Tele/Wide 键选择子菜单中的 FLICKERLESS B) 使用对焦键设置模式为 OFF ON * FLICKERLESS ; ᎖ሿ߹ᅄስ࿑ႄ ON 消除闪烁 对于 NTSC 系统 快门速度为 1/100 sec (对于 PAL 制式快门速度未 1/120 sec ).
ᔈࣅੰᒙ 4-7. ඡႥࣞᒙ A) 使用 Tele/Wide 键选择子菜单中的 SHUTTER B) 使用对焦键设置模式为 NORMAL 1/125 - 1/10000 4-8. ߱ဪᒙ A) 使用 Tele/Wide 键选择子菜单中的 INITIAL SET B) 使用对焦键将初始模式设为 ON 或 OFF 4-9.
ᄂၐᒙ 5. ᄂၐᒙ 5-1. ઓܪᄌᒙ: ࠥถ᎖Ᏼືᒦመာᔈࢾፃܪᄌ A) 使用 Tele/Wide 键在主菜单中设置 SPECIAL SET B) 使用 Tele/Wide 键选择子菜单中的 USER TITLE C) 使用 Tele / Wide 和对焦键设置标题位置和数据 5-2. ༹ᇠࣞࢯᑳᒙ A) 使用 Tele/Wide 键选择子菜单中的 B) 使用对焦键在 0 到 15 之间设置 SHARPNESS 5-3. नᒙ A) 使用 Tele/Wide 键选择子菜单中的 B) 使用对焦键设置模式为 ON OFF MIRROR 5-4.
ᄂၐᒙ 5-5. ঌᒋᒙ ࠥෝါ᎖ዕྻਜ਼ೡࣞখࡵܤঌᒋ A) 使用 Tele/Wide 键选择子菜单中的 B) 使用对焦键设置模式为 ON OFF COLOR 5-6. ᄴݛᒙ ࠥෝါ᎖ኀখᏐ௦ಭ።ࡼྻᄴࡒݛ A) 使用 Tele/Wide 键选择子菜单中的 B) 使用对焦键设置模式为 ON OFF 5-7. ߱ဪᒙ ྙਫ߱ဪෝါᆐ ON ۻখޣ߲ࡵܤᒙ ఎ WIDEBURST Ⴥᎌ SPECIAL ᄂၐ ถ A) 使用 Tele/Wide 键选择子菜单中的 INITIAL SET B) 使用对焦键将初始模式设为 ON 或 OFF 5-8.
Ꮵࣅଶހ 6. Ꮵࣅଶހᒙ 6-1. ଶހෝါᒙ A) 使用 Tele/Wide 键在主菜单中设置 B) 使用 Tele/Wide 键选择子菜单中的 C) 使用对焦键设置模式为 ON OFF MOTION DETECTION 6-2. ܰࢯᑳᒙ ࠥถ᎖ DETECTION ON ෝါ A) 使用 Tele/Wide 键选择子菜单中的 B) 使用对焦键调整到某一敏感度 6-3. ߱ဪᒙ ྙਫ߱ဪෝါᆐ ON ఎ ۻখޣ߲ࡵܤᒙ LEVEL SET Ⴥᎌ MOTION Ꮵࣅ A) 使用 Tele/Wide 键选择子菜单中的 INITIAL SET B) 使用对焦键将初始模式设为 ON 或 OFF 6-4.
F. OSD ᒙ 7. F. OSD ᒙ 7-1. ถᒙ A) 使用 Tele/Wide 键在主菜单中设置 F.
E. ැঢࣞᒙ 8. E.ැঢࣞᒙ: (భኡ) 8-1. E. ැঢࣞᒙ A) 使用 Tele/Wide 键选择子菜单中的 E.SENSITIVITY B) 使用对焦键在子菜单中选择您所需的敏感度模式 * ෝါၿኔ: OFF-X2 AUTO-X4 AUTO-X8 AUTOX10AUTO-X16 AUTO- X32 AUTO -OFF- X2 FIX-X4 FIX -X8 FIX -X10 FIX -X16 FIX - X32 FIX-OFF 8-2. ߱ဪᒙ ྙਫ߱ဪෝါᆐ ON ޣ߲ࡵܤᒙ ఎ E.SENSITITY ถۻখ A) 使用 Tele/Wide 键选择子菜单中的 INITIAL SET B) 使用对焦键将初始模式设为 ON 或 OFF 8-3.
ࣅზपᆍᒙ 9. ࣅზपᆍᒙ (భኡ) 9-1. ࣅზपᆍᒙ A) 使用 Tele/Wide 键在主菜单中设置 WDR B) 使用 Tele/Wide 键选择子菜单中的 WDR CONTROL C) 使用对焦键在子菜单中选择您所需的 WDR 模式 * ෝါၿኔ : OFF -- ON -- AUTO * WDR ᔈࣅෝါ᎖༓ࣞ۳ᄟୈሆ 9-2. ܰࢯᑳᒙ ࠥถ᎖ࢯᑳ WDR ࡼᐐፄ A) 使用 Tele/Wide 键选择子菜单中的 B) 使用对焦键调整到某一敏感度 9-3. ߱ဪᒙ ྙਫ߱ဪෝါᆐ ON ۻখޣ߲ࡵܤᒙ ఎ SENSITIVITY WDR ࣅზपᆍ ถ A) 使用 Tele/Wide 键选择子菜单中的 INITIAL SET B) 使用对焦键将初始模式设为 ON 或 OFF 9-4.
ືݩመာ (OSD) 以下某些功能在操作摄像机时会 在屏幕上显示 5 秒钟后消失 ถ OSD ৃါ 1. 对焦模式 无显示 ☞ 2. 背光 3. 快门速度 1 2 3 ႁී 自动模式 手动 / 强制自动模式 无显示 背光关闭 "BL"显示 背光补偿开 / 自动背光补偿模式 无显示 普通快门 ( NTSC: 1/60) PAL: 1/50) "Ff"显示 无闪烁模式 6 1/125 1/10,000 4. 摄像机 ID 5.
ືݩመာ (OSD) ถ 6. 待机 OSD ৃါ 7. 白平衡控 制模式 ႁී 在电源打开过程中摄像机处于待机状态 自动白平衡 S W S特殊自动白平衡 根据外部光线变化的调整模式 可使用 RED ADJUST 和 BLUE ADJUST (0~255) 修改 R/B 值后 维护模式为 AUTO 室内白平衡预设 (3200°K) 室外白平衡预设 (5100°K) M W 手动白平衡调整 P W 强制自动白平衡 此模式打开时 白平衡自动调整 保留最后自动追踪的白平衡 手动 在手动模式下可使用 HUE 控制 (0 ~ 99).
ਖৃ ߅ስ۸ 1/4" 隔行 CCD NTST, 高分辨率 811(H) X 508(V) 410K NTST, 普通分辨率 : 537(H) X 505(V) 270K PAL, 高分辨率 : 795 (H) X 596 (V) 470K PAL, 普通分辨率 : 537(H) X 597(V) 320K ᄴݛᇹᄻ 内部同步 ၺຳॊܦൈ 大约 480 线 NTSC 高分辨率 320 线 NTSC 普通分辨率 480 线 PAL 高分辨率 320 线 PAL 普通分辨率 (屏幕中央) ᄿ X 22 变焦 ( F 1.6 f = 3.9 ~ 85.8 mm ), 视频自动对焦 ၫ൩ܤୡ X 8 ( 总数码变焦 X 176 ) ᔢቃᑍී LVC-A910/912 SERIES : 1 Lux, AGC开 LVC-A911/913 SERIES : 0.01 Lux, X 32场累积 26 ቧᐅ܈ 大于48dB ྸහᇹᄻ ྸහຫൈ(H) ྸහຫൈ(V) 2:1隔行 15.734kHz(NTSC), 15.625kHz(PAL) 59.
ਖৃ ୡ௦ ືݩመာ (OSD) ࢟Ꮞገཇ 0.01m (广角), 1.0m (远景) 开/关 DC 12V ၁ຫၒ߲ 复合输出75Ω 电阻 / Y,C 独立 5W ᔫᆨࣞ 0°C - 45°C ᔫဘࣞ 0% RH - 60% RH ࡀᆨࣞ -20°C - 60°C, 0% RH - 85% RH ߛࡁ 56.