Operating Instructions LVC-DV100 HM HP LVC-DV101 HM HP Before installing and using the camera, please read these instructions thoroughly and retain them for later reference.
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
1 Safety Precautions Do not attempt to disassemble the camera To prevent electric shock, do not remove screws or covers. There are no user serviceable parts inside. Ask a qualified service personnel for servicing. Do not use strong solvents or detergents Use a dry cloth to the camera when it is dirty. If it is hard to remove the dirt on the camera, use a mild detergent and wipe it gently. Before operating, please check proper temperature, humidity and power source ratings.
2 What's in the box Video Cable Camera Body M4 Tapping Screws (2EA) (Pan Lock Screw) Optional Adapter (DC 12V, 300mA)
3 Construction Front View LG logo 4-pin Dip Switch Tilt Base Zoom Lever Tilting Lock Screw Focus Lever Side View Dome Cover Lens Tilting Lock Screw Dome Cover Separatory Spring
4 Construction Rear View Dome Cover Separatory Spring Power In Video Out (+) (-) DC12V VIDEO NC N.C (Option: Ext. Sync.
5 Installation Video Cable Connection RED Cable BLACK Cable (+) (-) DC12V VIDEO NC WHITE Cable 1. RED : Connect the RED Cable to 1(+). 2. BLACK : Connect the BLACK Cable to 2(-). 3. WHITE : Connect the WHITE Cable to 3(V).
6 Installation Camera Installation 1. Aim the LG logo of the Dome Camera to face the place that you wish to watch. 2. Tighten the M4 Tapping Screws to fix the Dome Camera on the ceiling, then adjust the Pan (Left / Right) by moving the Pan Base. Tighten the M4 Tapping Screws after adjustment. 3. Loosen the Tilting Lock Screw. Adjust the Tilt (Up / Down) by moving the Tilt Base then tighten Tilting Lock Screw. 4.
7 Installation NOTE • When you disassemble the Dome Cover, lift the Dome Cover Separatory Spring on the opposite side of LG Logo and turn the Dome Cover clockwise simultaneously. Dome Cover Separatory Spring • When you install the camera, handle with care. The camera could be damaged by improper handling or storage. • If this camera is mounted on the other places except ceiling, you need an extra bracket for mounting.
8 Installation Camera Connection Connect the Power Adapter (DC12V, 300mA; optional) to the Power Input Jack of the camera as shown below.
9 Setup 4-pin Dip Switch Setting This camera has the 4-pin Dip Switch inside of the camera for setting. 1. ALC / ELC : ELC (Electronic IRIS), ALC (Auto IRIS) The default setting is ALC. 2. Y/ DC IRIS : When you use Video Lens or DC IRIS Lens The default setting is DC. (using the fixed lens) 3. BLC : Backlight Compensation The default setting is OFF. 4. ABL : Auto BLC The default setting is OFF. ALC Y ELC DC BLC ABL OFF OFF NOTE No. 1 and 2 must be set as a default mode.
10 Setup Backlight Compensation Setting Backlight compensation eliminates strong background light which makes the camera picture dark such as a spotlight. You can select the mode for adjusting the iris lens. There are two mode as follows. 1. BLC : Set the BLC to ON. The lens iris is manually fixed at the value that you have set regardless of an object. ALC Y ELC DC BLC ABL OFF OFF 2. ABL : Set the ABL to ON. The lens iris is automatically adjusted according to the brightness of an object.
11 Troubleshooting Check the following guide for the possible cause of a problem before contacting service. • The picture is poor. Does the Dome Cover have lots of dust on the surface? Use a dry cloth to clean the camera when it is dirty. Smear may be caused to the screen of night than daytime. Adjust the Focus by moving the Focus Lever. • Contrast of the screen is not clear. Check the condition of the monitor. Alight source such as a spot light causes burn-in on the display screen.
12 Dimension ø100 91mm 10mm 31mm ø121.
13 Specifications Model Signal System Total / Effective Pixels Pick-Up Device Lens Angular Field of View Focus Signal Process Scanning System Sync. System Scanning Frequency Resolution S/N Ratio Standard Illuminance Sensitivity (1/3 output) Video Output Signal Gain Control Shutter Speed White Balance Back Light Power Source Power Consumption Operating Temp. Storage Temp.
MEMO
