Operating Instructions LVC-S10/LVC-S101 LVC-S20/LVC-S201 Before installing and using the camera, please read these instructions throughly and retain them for later reference.
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
Contents Features ..................................................................................................................................3 Cautions for Safe Operation ......................................................................................................4 Operating Controls and Their Functions ..............................................................................5-6 Connections .................................................................................................
Cautions for Safe Operation Power Supply S10, S20 : They must be operated with a AC 24V class 2 power supply and DC12V alternatively. In the U.S.A, use a Power supply which is UL Listed. In the Canada, use a Power supply which is CSA Certified. * Notes:Be careful of AC frequency when the camera is operated with Line lock mode.
OPERATING CONTROLS AND THEIR FUNCTIONS 1 3 4 7 Control names and Location 2 5 6 8 POWER POWER AC 100-240V~ Da- Da+ Dr+ Dr- Alarm Out VCC Video GND AC 24V IN 1 DC 12V IN Da- Da+ Dr+ Dr- Alarm Out VCC Video GND 2 GEN-LOCK Class 1 Only 9 10 VIDEO OUT VIDEO ELC DC GND GEN-LOCK VIDEO OUT VIDEO ELC DC V.PHASE V.PHASE Class 2 Only 11 12 13 14 S101,S201’ S S10,S20’ S 1. Tripod adaptor This adaptor can also be attached on the bottom of the camera 2.
OPERATING CONTROLS AND THEIR FUNCTIONS 1 2 The Adjustment method of Line Lock Phase When using a camera switcher to connect 2 cameras or more to one monitor, there may be a vertical roll of the images when switched. In such a case, refer to the below. -The vertical sync phase can be manually adjusted within the range approximately from -90o to 90o. - Switch the display on the monitor from camera1 to camera2. Adjust the V.PHASE volume on camera2 until the vertical roll of the image stops.
CONNECTIONS Power Connection POWER LVC-S101, LVC-S201 (AC100V-AC240V) 1. Connect the AC power cord (supplied as an accessory) to the power cord socket of the camera. 2. Connect the AC power cord to an electrical outlet of 100V - 240V AC 100-240V~ G Cl 1O l DC 12V IN 12 V DC (10.5V~24V) AC 240V IN 1 2 24 VAC (19.5V~28V) GND 1 2 LVC-S10, LVC-S20 (DC12V/AC24V Compatible) 1.
Flange-Back Focus adjusting lever 1. Mount the lens by turning it clockwise on the lens mount of the camera. 2. Set the slide switch of rear panel to your lens type 3. Connect the lens cable to the auto iris lens connector on the side of the camera. 4. If the lens connection is not connector type but wired cable type, connect this cable to iris terminal block at rear panel. In this case, note the terminal assignment of DC or Video lens. Notes: Rotate the lever clockwise until it stops.
BACK FOCUS ADJUSTMENT 1. Loosen the screws on the flange -back adjusting lever. 2. Turn the flange-back adjusting lever to the proper focus position. 3.
INSTALLATION OF CAMERA This camera is mounted with tripod which makes it possible to install from both of the bottom and the top of the unit as illustrated.
FUNCTION SET UP 1. CAMERA SETUP MENU MENU 1 Brightness Brightness Up/Down Shutter ELC DC/Video Auto AGC On/Off Flickerless/ Shutter Up/Down Back Light On/Off Sharpness Normal/ Soft/ Sharp WBC Mode ATW/AWC ATW R/B Sync.
MENU 2 Motion DET On/Off Camera ID On/Off Level Set ID Set Area Set 12 Wide Burst On/Off Inital Set On/Off Sensitivity
2. SETTING THE MENU Up Button Left Button Set Switch Right Button Down Button This camera has user setting menu that is displayed on the monitor. To set OSD function, use the following buttons on the side panel. Up/Down Button ( / ) : This button is used to select function . Left/Right Button ( / ) : This button is used to set or adjust parameters. Center Button ( ) : This button is used to access menu mode and exit the menu. * The function of Digital Zoom is directly operated with Left / Right button.
• Editing the Camera Setup Menu 1 MENU 1 BRIGHTNESS SHUTTER 1/250 AGC ON BACKLIGHT OFF SHARPNESS NORMAL WBC MODE ATW SYNC MODE INT 1. BRIGHTNESS Adjustment - Use the button to move the cursor to “BRIGHTNESS” / - Use the button to adjust the degree of brightness. / 2. Shutter Speed Setting - Use the button to move the cursor to “SHUTTER” / Use the button to set the shutter speed mode.
MENU 1 BRIGHTNESS SHUTTER 1/250 AGC ON BACKLIGHT OFF SHARPNESS NORMAL WBC MODE ATW SYNC MODE INT ATW SETTING R POINT B POINT MOVE POSITION , CHANGE DATA , RETURN TO MAIN 6 WBC(White Balance Control)Mode setting - Use the button to move the cursor to “WBC MODE” / - Use the button to set the mode (ATW, AWC) / - Use the ( ) to move to submenu in ATW menu. - Use the button to move the cursor to “R POINT” or “B / POINT”.
• Editing the Camera Setup Menu 2 MENU 2 MOTION DET CAMERA ID ON ON WIDE BURST ON INITIAL SET OFF MOTION DETECT SENSITIVIY MASK AREA SET RETURN 16 MOVE POSITION , CHANGE DATA , 1. MOTION DETECTION Setting button to move the cursor to “MOTION DET”. - Use the / - Use the button to set the mode On or Off. / If the MOTION DET is set, “Motion Detected” appears on the top of monitor. * Set the SENSITIVITY - Press the button to move to submenu. button to move the cursor to “SENSITIVITY”.
ABCDEFGHIJKLMNOP QRSTUVWXYZabcdef ghijklmnopqrstuv wxyz0123456789., ’?!&* :()<>/+- RETURN POSI CLEAR FRONT DOOR *When the object is put in the place where the degree of light is not constant. *When the digital zoom is working, the Motion detection does not work . Please set the zoom switch to the end of wide mode. 2. CAMERA ID Setting - Use the button to move the cursor to “CAMERA ID” / - Press the button to move to submenu.
MENU 2 MOTION DET CAMERA ID ON ON WIDE BURST ON INITIAL SET OFF MENU 2 18 MOTION DET ON CAMERA ID ON WIDE BURST ON SENSITIVITY X2 AUTO INITIAL SET OFF 3. WIDE BURST Setting - Use the button to move the cursor to “WIDE BURST” / - Use the button to set the On / Off mode. / WIDE BURST Setting is useful to prevent attenuation of burst signal in case of long distance installation. 4.
Specification Model Signal System Total/Effective Pixels Pick-Up Device Lens Auto Iris Signal Process Digital Zoom Scanning System Sync. System Scanning Frequency Resolution S/N Ratio Standard Illuminance Sensitivity (1/3 Output) Video Output Signal Gain Control Electronic Exposure Shutter Speed White Balance Back Light Bright control Motion Detection Wide Burst Sharpness Power Source Power Consumption Operating Temp. Storage Temp.
Model Signal System Total/Effective Pixels Pick-Up Device Lens Auto Iris Signal Process Digital Zoom Scanning System Sync. System Scanning Frequency Resolution S/N Ratio Standard Illuminance Sensitivity (1/3 Output) Video Output Signal Gain Control Electronic Exposure Shutter Speed White Balance Back Light Bright control Motion Detection Wide Burst Sharpness Power Source Power Consumption Operating Temp. Storage Temp.
Model Signal System Total/Effective Pixels Pick-Up Device Lens Auto Iris Signal Process Digital Zoom Scanning System Sync. System Scanning Frequency Resolution S/N Ratio Standard Illuminance Sensitivity (1/3 Output) Video Output Signal Gain Control Electronic Exposure Shutter Speed White Balance Back Light Bright control Motion Detection Wide Burst Sharpness Power Source Power Consumption Operating Temp. Storage Temp.
Model Signal System Total/Effective Pixels Pick-Up Device Lens Auto Iris Signal Process Digital Zoom Scanning System Sync. System Scanning Frequency Resolution S/N Ratio Standard Illuminance Sensitivity (1/3 Output) Video Output Signal Gain Control Electronic Exposure Shutter Speed White Balance Back Light Bright control Motion Detection Wide Burst Sharpness Power Source Power Consumption Operating Temp. Storage Temp.
P/NO.
