Before Operation 7
NOTE: Your air conditioner may differ from the one shown.
Parts supplied: Check that all parts are included in parts package. A. Top channel B. Foam seal C. Window lock bracket (3) A B ” screws (3) D. ” screws (7) E. F. Side curtains (2) G.Side curtain frames (2) D C E F G Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.
Window Installation Window opening measurements: MODEL 5000 BTU Dimension A(inch) Min A. Width A(inch) Max 23 1/4”(59.1cm) 36”(91.4cm) B(inch) Min 12 3/8”(31.4cm) B. Height A B Unpack the Air Conditioner Remove Packaging Materials NOTE:The air conditioner must set upright for one hour before operating. Remove and dispose of/recycle packaging materials. Remove tape and glue residue from surfaces before turning on the air conditioner.
Install Side Curtains 3. Slide the side curtain frame into the top channel on the top of the air conditioner and the track on the bottom of the air conditioner. 4. Slide the side curtain frame as close to the air conditioner as necessary to lock the side curtain to the frame. Repeat above steps for the left-hand side curtain and frame. NOTE: Attach curtains to the air conditioner before placing the air conditioner in window. 1.
Positioning the Air Conditioner A B ABOUT 1/4” NOTES: Handle the air conditioner gently. Be sure your air conditioner does not fall out of the opening during installation or removal. The place where the power cord exits the air conditioner should be no more than 6 ft (183 cm) from a grounded outlet. Do not block the louvers in the front panel. Do not block the louvers on the outside of the air conditioner. 1.Tilt the air conditioner about 1/4” down towards the outside for proper condensate water drainage.
Bottom View Completing the Installation 1. Insert the foam seal behind the top of the lower window sash and against the glass of the upper window. A B 5. A. Top of lower window sash B. Foam seal 2. Place the window lock bracket as shown. Use a ” drill bit to drill a starter hole through the hole in the window lock bracket and into the upper window. 3. Attach the window lock bracket to the upper window with one ” screw to secure the window in place. A 4.
POWER Turn air conditioner on or off. SPEED Low : Low speed fan operate with optional cooling. High: High speed fan operate with optional cooling. NORMAL FAN a. Turn the SPEED mode switch to the “HI“ or the “LOW“ setting. b. Set the thermostat control to the “FAN ONLY” setting . NORMAL COOLING a. Turn the SPEED mode switch to the “HI“ or the “LOW“ setting. b. Set the thermostat control to the desired temperature.(The mid-point is a good starting position .
Use the tab to direct the airflow right or left. A A. Tab NormalSounds When your air conditioner is operating normally, you may hear sounds such as: Droplets of water hitting the condenser, causing a pinging or clicking sound. The water droplets help cool the condenser. Air movement from the fan. Clicks from the thermostat cycle. Vibrations or noise due to poor wall or window construction.
Your new air conditioner is designed to give you many years of dependable service. This section tells you how to clean and care for your air conditioner properly. CleaningtheAirFilter filter helps remove dust, lint, and other particles from the air and is important for best cooling and operating efficiency.Check the filter every 2 weeks to see whether it needs cleaning. Note:Do not operate the air conditioner without the filter in place. 1. Turn off the air conditioner. 2.
/* &XVWRPHU ,QIRUPDWLRQ &HQWHU 5HJLVWHU \RXU SURGXFW 2QOLQH！ /* (/(&7521,&6 ,1& 6\OYDQ $YH (QJOHZRRG &OLIIV 1- ZZZ OJDSSOLDQFHV FRP
