INSTALLATION English, Spanish 07/09/2018 1, 737K

ENGLISH
1
BEFORE BEGINNING
Remove all tape and packing materials before using the oven. Dispose of all plastic bags after
unpacking the oven.
Never allow children to play with packing materials.
You can download an installation manual at http://www.lg.com.
IMPORTANT SAFETY INSTRUCTIONS
Read and follow all instructions before using the oven to prevent the risk of fire, electric shock,
injury to persons, or damage when using the oven. This guide does not cover all possible
conditions that may occur. For further assistance contact the service agent or manufacturer.
This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or
hurt you and others. All safety messages will follow the safety alert symbol and either the
word “WARNING” or “CAUTION”. These words mean :
WARNING
This symbol will alert you to hazards or unsafe practices which could cause
serious bodily harm or death.
CAUTION
This symbol will alert you to hazards or unsafe practices which could cause
bodily injury or property damage.
SAFETY INSTALLATION REQUIREMENTSPart 1 Part 2
• The information in this manual should be followed exactly.
- Failure to do so could result in fire or electrical shock, causing property damage, personal
injury or death.
• DO NOT put any weight on the oven door. Never allow anyone to climb, sit,
stand or hang on the oven door.
- The oven could be tipped and injury might result from contact with hot food or the oven itself.
•
The electrical power must be shut off while the electrical connections are being made.
- Failure to do so can result in severe personal injury, death or electrical shock.
• New branch-circuit installations (1996 NEC), mobile homes, recreational
vehicles, or installations where local codes prohibit grounding through the
neutral conductor require 4-wire branch-circuit connection.
• Improper connection of aluminum house wiring to copper leads can result in
an electrical hazard or fire. Use only connectors designed for joining copper to
aluminum and follow the manufacturer’s recommended procedure closely.
• Mounting screws must be used.
- Failure to do so can result in the oven falling out of the cabinet, causing serious injury.
WARNING
• Make sure the cabinets and wall coverings around the oven can withstand the
temperature (up to 194˚F[90˚C]) generated by the oven.
- Discoloration, delamination or melting may occur.
• DO NOT remove spacers on the side walls of the built-in oven.
- These spacers center the oven in the space provided. The oven must be centered to prevent
excess heat buildup that may result in heat damage or fire.
• DO NOT block the oven air exhaust located at the bottom of the oven.
- Blocking the exhaust may cause cabinet damage and product malfunction.
CAUTION
IMPORTANT NOTE
This installation must be completed by a qualified
installer or technician.
Proper installation is the responsibility of the
installer and product failure due to improper
installation is NOT covered under warranty.
• Installer: please retain these instructions for local
inspector’s reference, then leave them with the
consumer.
• Consumer: please read and keep these
instructions for future reference and be sure to
read the entire OWNER’S MANUAL prior to use.
• Do not use parts other than the provided
components when you install the product.
MATERIALS INCLUDED
4X14
6 Wood Screws(Black) For Lower Mounting
(4 needed for installation and 2 extras)
4X14
6 Wood Screws(Silver) For Upper Mounting
(4 needed for installation and 2 extras)
REQUIRED TOOLS
Phillips Screwdriver Drill
MATERIALS NEEDED
Junction Box Wire Nuts
36” (91 cm)
of String
3/4” Conduit
Connector
Measure the current cutout dimensions and compare them to the cutout dimensions shown
below. Little or no cabinet work may be necessary.
IMPORTANT NOTE
• The cabinet base platform must be able to support 202 lbs (91.65 kg) for a Microwave Combination
Wall Oven. If the cabinet does not have a solid bottom, two braces or runners must be installed level
with the bottom of the cutout to support the weight of the oven. Make sure the base is level and the
front of the cabinet is square. If the cabinet base is not level, the oven racks will tend to slide out
when opening the door.
• If marks, blemishes or the cutout opening are visible above the installed oven, it may be necessary
to add wood shims under the runners and front trim until the marks or opening are covered.
• If the cabinet does not have a front frame and the sides are less than 3/4” (1.9 cm) thick, shim both
sides equally to establish the cutout width.
• The junction box must be flush with the rear wall of the cabinet as shown below.
• Allow at least a 23” clearance for the door depth when it is open.
• Kitchen cabinets in contact with the oven must be heat resistant up to 194°F (90°C), and fronts of
nearby units up to at least 158°F (70°C).
1
INSTALLATION DRAWINGS (FOR 30” MICROWAVE COMBINATION WALL OVEN)
Cutout Dimensions
Junction Box
Location
41”
(1041.0 mm)
30”
23”
5”
28 1/2” Min.
28 5/8” Max.
43 7/16” Min.
(1103 mm)
43 1/2” Max.
(1106 mm)
Allow 1”
minimum for
overlap of oven
Allow 1”
minimum for
overlap of oven
23 1/2”
Minimum cutout location from floor 12”
Cabinet Width 30” (762 mm)
Recommended
Minimum
Cutout Location
from Floor 12” (304.8 mm)
Cutout Depth 23 1/2” Min. (596.9 mm)
Cutout Width 28 1/2” Min. (723.9 mm)
28 5/8” Max. (727 mm)
Cutout Height 43 7/16” Min. (1103 mm)
43 1/2” Max. (1106 mm)
Product Dimensions
27 3/8” (69.5 cm)
43 13/16”
(111.3cm)
43 3/16”
(109.7 cm)
27 1/6”
(69 cm)
29 3/4” (75.5 cm) 23 3/8” (59.3cm)
2
PREPARATION FOR MOVING THE OVEN
Remove any packing material from the oven before installing the oven.
1. Remove all tape from around the oven.
2. Open the oven door and remove packaging materials and oven racks inside the oven.
3. Door removal is not a requirement for installation of the oven, but is an added convenience.
To remove the door, follow the steps below.
4. Place the oven on a table or platform even with the cutout opening. (The table or platform
must support 202 lbs [91.65 kg] for a Microwave Combination Wall Oven.)
5. Remove the metal bottom trim from the oven. It will be installed at the end of the installation
process. The trim is wrapped separately and taped to the top of the unit.
Step. 1
Fully open the door.
Hinge
lock
Slot
Lock
Unlock
Step. 2
Pull the hinge locks
up towards the
door's frame, to the
unlocked position.
Step. 3
Firmly grasp both sides of the door at the top.
Step. 4
about 5
Close door to the door
removal position, which is
approximately 5 degrees.
Step. 5
Lift door up and out until
the hinge arm is clear of
the slot.
IMPORTANT NOTE
• Do not lift the door by the handle. The oven
door is very heavy. Firmly grasp the door by
the sides before lifting it off the hinges.
• Do not lay the oven door on its handle. Doing
so may cause dents or scratches.
• Use two or more people to lift or move the
oven into the cabinet opening. Use caution
when lifting the oven and wear gloves to
protect hands from any sharp edges. Failure to
follow these instructions may result in injury.
Spacer
1
ELECTRICAL CONNECTION REQUIREMENTS
Follow the electrical connection requirements below.
Ensure that dedicated circuit protection is prepared as recommended and that the oven is
grounded properly.
IMPORTANT NOTE
Be sure the wall oven is installed and grounded properly by a qualified installer or service
technician.
• This wall oven must be electrically grounded in accordance with local codes or, in their
absence, with the National Electrical Code ANSI/NFPA No.70- latest edition in United States, or
with CSA Standard C22.1-1982 and C22.2 No.01982 (or latest edition), Canadian Electrical Code,
Part1, and all local codes and ordinances.
• This wall oven must be supplied with the proper voltage and frequency, and connected to
an individual, properly grounded branch circuit, protected by a circuit breaker or fuse. For
the circuit breaker or fuse required by this model, see the rating plate to find the wattage
consumption and refer to the table below to get the circuit breaker or fuse amperage.
• A Microwave Combination Wall Oven can consume up to 7,800 W at 240 VAC.
A 50 Amp circuit breaker with wire gauge #8 AWG must be used.
• Do Not ground to a gas pipe.
• Do Not have a fuse in the neutral or grounding circuit.
• A U.L.-listed conduit connector must be provided at the junction box.
2
ELECTRICAL CONNECTION
Prepare the electrical connection as follows:
1. Turn off the circuit breaker or remove fuses to the oven branch circuit.
2. With the oven positioned directly in front of the cabinet opening, connect the flexible conduit
to the electrical junction box as shown below. Position the conduit in such a manner that it
will lie on top of the oven in a natural loop when the oven is installed.
Junction Box
Location
41” Min
for Microwave Combination Wall Oven
Junction Box must be recessed
and conduit connector must be
used at Junction Box.
5” Min
3. If local codes permit connection of the frame grounding conductor to the neutral(white) wire,
follow the instructions for a 3-wire circuit connection.
4. If used in mobile homes or new construction, or a recreational vehicle, or local codes do not
permit connection of the frame grounding conductor to the neutral(white) wire, follow the
instructions for a 4-wire circuit connection.
1
CABINET INSTALLATION
Install the oven into the cabinet as follows:
1. Slide the oven into the opening.
a. Loop (do not tie) a 36” (91 cm) string around the conduit before the oven is slid into place. Lay
the string over the top of the oven and use it to keep the conduit from falling behind the oven.
b. Lift oven into cabinet cutout using the oven opening as a grip. Carefully push against the oven
front frame.
Do not push against outside edges.
c. While sliding the oven back, pull the string so that the conduit lies on the top of the oven in a
natural loop.
d. When you are sure the conduit is out of the way, slide the oven 3/4 way back into the opening.
Remove the string by pulling on one end of the loop.
2. Secure the oven.
a. Using the mounting holes on the oven side
trim as a guide, drill pilot holes for screws
provided. (For securing the Combi Oven, use
a minimum of 4 screws, one on each side in
both the upper and lower ovens.)
b. Secure the oven to the cabinet with screws
provided.
If the cabinet is particle board, you must use
3/4” particle board screws. These may be
purchased at any hardware store.
3. Install the metal bottom trim.
a. Place the metal bottom trim centered over the
pre-drilled mounting holes on the lower base.
b. Using 3 screws provided, secure the bottom
trim to the bottom edge of the cabinet.
4. Reinstall the oven door.
ELECTRICAL CONNECTIONS INSTALL THE OVENPart 3 Part 4
IMPORTANT NOTE
• The wall ovens must be hard wired (direct wired) into an approved junction box. A plug and
receptacle is not permitted on these products.
• DO NOT shorten the flexible conduit. The conduit connector must be securely attached to the
junction box and the flexible conduit must be securely attached to the conduit connector. If the
flexible conduit will not fit within the connector, do not install the oven until a connector of the
proper size is obtained.
• You will need to purchase an appropriate conduit connector to complete the connection of the
conduit to the junction box.
NOTE TO ELECTRICIAN
The power leads supplied with the appliance are UL, CSA recognized for connection to larger
gauge household wiring. The insulation of these leads is rated at temperatures much higher than
the temperature rating of household wiring. The current carrying capacity of the conductor is
governed by the wire gauge and the temperature rating of the insulation around the wire.
To connect to a three-wire circuit, follow these
steps:
1. Connect the oven ground (green) wire and
neutral (white) wire to the branch circuit
neutral (white or gray) wire, using a wire
nut.
2. Connect the oven red wire to the branch
circuit red (L2) wire in accordance with local
codes, using a wire nut.
3. Connect the oven black wire to the branch
circuit black (L1) wire in accordance
with local codes, using a wire nut. If the
residence red, black or white wires are
aluminum conductors, see WARNING.
4. Install the junction box cover.
White
Green
Black
Red
Neutral
Wire nut
Junction Box
To connect to a four-wire circuit, follow these
steps:
1. Separate the oven ground and white wires
if necessary.
2. Connect the oven ground (green) wire
to the branch circuit ground (green) wire
in accordance with local codes, using a
wire nut. If the residence red, black or
white wires are aluminum conductors, see
WARNING.
3. Connect the oven white wire to the branch
circuit neutral (white or gray) wire in
accordance with local codes, using a wire
nut.
4. Connect the oven red wire to the branch
circuit red (L2) wire in accordance with local
codes, using a wire nut.
5. Connect the oven black wire to the branch
circuit black (L1) wire in accordance
with local codes, using a wire nut. If the
residence red, black or white wires are
aluminum conductors, see WARNING.
6. Install the junction box cover.
White
Green
Black
Red
Neutral
Wire nut
Junction Box
3-Wire Circuit Connection 4-Wire Circuit Connection
Step. 1
Firmly grasp both
sides of the door
at the top.
Step. 2
With the door at the
same angle as the
removal position,
seat the indentation
of the hinge arm into the bottom edge of the hinge
slot. The notch in the hinge arm must be fully
seated into the bottom of the slot.
Step. 3
Fully open the door. If the door will not fully
open, the indentation is not seated correctly in
the bottom edge of the slot.
Step. 4
Push the hinge locks up
against the front frame
of the oven cavity to the
locked position.
Step. 5
Close the oven door.
Hinge arm
Bottom
edge of
slot
Indentation
Hinge arm
Hinge lock
Mounting
Hole
Locations
Mounting
Hole
Locations
Trim Screws
Side
Trim
Side Trim
Lower base
Metal Trim:
Correct
position
Metal Trim:
Wrong
position
Metal
bottom
trim
1
CHECKING OPERATION
Each of the functions has been factory checked before shipping. However, it is suggested that you
verify the operation of the oven once more. Refer to the Owner’s Manual. Follow the instructions for
the basic check.
- Turn on power supply. The initial signal sound is heard and the Clock segment appears in the display.
Common
1. Check the operation of the broil mode. When the oven is set to broil, the upper element in the oven
should become red. After a few minutes, partially open the oven door. You should feel heat from
the oven. Press CLEAR/OFF.
2. Check the operation of the convection bake mode. After setting the oven to 350 °F / 177 °C for
convection baking, the fan inside the oven should come on with the door closed. Press CLEAR/OFF.
3. Turn on and off the oven light to check the lights are in normal condition.
Upper Oven
1. Check the Microwave function. Place a glass bowl filled with water in upper oven. Turn the
microwave on for 1 minute. The water should be hot. Press CLEAR/OFF.
Lower Oven
1. Check the operation of the bake mode. Set the oven to bake at 350 °F /177 °C. After a few minutes,
the temperature in the display should increase. Press CLEAR/OFF.
2.
Check the operation of the burner for each convection mode. After setting the oven to 350 °F / 177 °C
for each convection mode, the back element should light up and the fan inside the oven should come
on with door closed.
IMPORTANT NOTE
• A small amount of smoke and odor may be noticeable during the initial break-in period.
• If the oven does not operate properly or an F-, followed by a number, appears in the display, see the
Owner’s Manual for the troubleshooting list. The list includes common occurrences that are not the
result of defective workmanship or materials in this product. If the problem occurs continuously,
contact the dealer.
• Refer to the warranty in the Owner’s Manual for the LG toll-free service number and address.
OPERATION CHECKLISTPart 5
COMbINATION WALL OVEN Installation Guide
MHK66625101_02