W1_MCD112-212_ENG_MFL40387022 MODEL : MCD112 MCD212 ENGLISH
There is so much your Hi-Fi system can do Record from a CD, AUX, USB or radio to cassette Go to page 8 Contents Setting up About Player About Remote control Listening to CDs Connecting your portable USB player - OPTIONAL Listening to the radio Listen to cassette tapes Recording USER EQ Setting the Clock Use your player as an alarm clock About MP3/WMA Safety Precaution Troubleshooting Specifications 3 4 5 6 6 7 7 8 8 8 9 9 10 11 11 Lull me to sleep and wake me up Go to page 9 Before connecting, operatin
Setting up 1 Connect the speaker cables to the player Cables from the left-hand speaker connect to the terminal marked L (left) + (plus) and - (minus). Cables from the right-hand speaker are connected to the terminal marked R (right) + (plus) and - (minus). To connect the cable to the player, press each of the four square plastic finger pads on the rear of the player. The connector will open ready to receive a cable.
About Player POWER You can set up the unit into an economic power save mode. In the power-on status, press and hold 1/] (POWER) for about 3 seconds. To cancel power save mode, press 1/] (POWER). ST./MONO Press ST./MONO. This will change the tuner from stereo to mono and usually improve the reception. MP3 OPT. (MP3 Optimizer) This function is optimized for compressible MP3 files so that it improves the bass sound. DEMO Press DEMO in power off state to demonstrate the function on display window.
About Remote control Search for a folder of MP3/WMA files When a CD containing MP3/WMA files in several folders is being played, press PRESET/FOLDER to select the folder you want to play. Fall asleep while listening to your player Firstly, start a radio station or music. Press SLEEP on the remote one or more times to select a delay of between 10 and 180 minutes, after which the player will turn off.
Listening to CDs ON PLAYER 1. Open the CD drawer: 2. Select the CD tray : 3. Insert the CD : Label facing up. 4. Close the CD drawer: The display will show the total number of tracks (files). 5. Select the CD function: 6. Start the CD playing: 7. To stop a CD playing: Z OP./CL. D.SKIP ON REMOTE D.SKIP Connecting your portable USB player - OPTIONAL The advantage of connecting your portable USB player through the system’s USB port is that the portable device can be controlled from the system.
Listening to the radio Make sure both the FM and AM aerials are connected. Choose a ‘preset number’ for a radio station When storing a radio station, the preset number can be chosen. When the player automatically shows a preset number press PRESET/FOLDER then. Press PROGRAM/MEMO to save the number. Delete all the saved stations 1. Select either AM or FM: 2. Select the radio station: 3. To ‘save’ a radio station: A preset number will show in the display. 4.
Recording USER EQ Record from a CD, AUX, USB or radio to cassette You can listen to music with the desired sound effect (BASS, MIDDLE and TREBLE). Wind the tape to the point recording starts. Use only normal tapes. ON PLAYER 1. Open the TAPE 2 door : 2. Insert a blank tape : 3. Close the TAPE 2 door : 4. Select a mode (FM, AM, CD, USB (OPTIONAL) or AUX) in which you want to record : - Start playing the source you want to record. 5. Puts the unit in standby more for recording: 6.
Use your player as an alarm clock Press and hold TIMER for two seconds. Each function, TUNER, CD, USB, TAPE flashes for two seconds. Press SET when the function you want to be woken by is showing. If you choose TUNER, ‘PLAY’ and ‘REC’ flash, PLAY and REC. Choose one of them. If you choose TUNER and PLAY you will be shown the stations you have saved as presets. Use TUNING (-) or TUNING (+) to select the station you want, then press SET. You will be shown the ON TIME display.
Safety Precaution CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
Troubleshooting Symptom No power. No sound. The unit does not start playback. The remote control does not work properly. Unable to record. Specifications Cause Correction • Plug the power cord into the wall outlet securely. • The power of the external source • Switch on the external source equipment. equipment is turned off. • Set the speaker cable to the • The speaker cable is connected correct position, then turn on the to a wrong position. unit again by pressing POWER. • Insert a playable disc.
P/NO : MFL40387022
