OLED TV OLED55E6* OLED65E6* AA AA CR2032 X4 (M4 x L12) www.lg.
1 2 3 4
ANTENNA/ CABLE IN HDMI IN HDMI IN / ARC USB IN LAN AUDIO OUT/ H/P OUT OPTICAL DIGITAL AUDIO OUT AV IN COMPONENT IN
OPTICAL DIGITAL AUDIO OUT AV IN VIDEO L/MONO AUDIOR COMPONENT IN AUDIO VIDEO
1 2 2 1 1 2 3 3 AA 4 3 4
0 1 2 OLED55E6P-C OLED65E6P-C 1237 1461 767 893 175 200 767 893 56.7 56.7 18.5 24.8 17.1 22.
*MFL69355206*
Safety and Reference Please read this manual carefully before operating your TV and retain it for future reference. www.lg.
Safety instructions Please read these safety precautions carefully before using the product. WARNING ENGLISH Clean only with dry cloth.
Des icca nt Keep the anti-moisture packing material or vinyl packing out of the reach of children. Anti-moisture material is harmful if swallowed. If swallowed by mistake, force the patient to vomit and visit the nearest hospital. Additionally, vinyl packing can cause suffocation. Keep it out of the reach of children. Dispose of used batteries carefully to ensure that a small child does not consume them. Please seek Doctor- Medical Attention immediately if child consumes batteries.
CAUTION Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus. Install the product where no radio wave occurs. ENGLISH Do not install this product on a wall if it could be exposed to oil or oil mist. This may damage the product and cause it to fall. There should be enough distance between an outside antenna and power lines to keep the former from touching the latter even when the antenna falls.
Only use the specified type of battery. This could cause damage to the remote control. ENGLISH Do not mix new batteries with old batteries. This may cause the batteries to overheat and leak. Please follow the installation instructions below to prevent the product from overheating. •• The distance between the product and the wall should be more than 10 cm. •• Do not install the product in a place with no ventilation (e.g., on a bookshelf or in a cupboard).
Avoid touching the screen or holding your finger(s) against it for long periods of time. Doing so may produce some temporary or permanent distortion/damage to screen. ENGLISH When cleaning the product and its components, unplug the power first and wipe it with a soft cloth. Applying excessive force may cause scratches or discolouration. Do not spray with water or wipe with a wet cloth. Never use glass cleaner, car or industrial shiner, abrasives or wax, benzene, alcohol etc.
WARNING! Symbols Refers to alternating current(AC). Refers to direct current(DC). Refers to class II equipment. Viewing 3D imaging (Only 3D models) CAUTION •• Guardians should not leave children unsupervised who are watching a 3D video. Guardians should make children stop watching the video and take a rest if they experience eye fatigue, headache, or dizziness. •• When viewing a 3D video, some may experience discomfort such as a headache, dizziness, fatigue, or blurred vision.
Preparing Lifting and moving the TV NOTE ENGLISH •• If the TV is turned on for the first time after it was shipped from the factory, initialization of the TV may take a few minutes. •• Image shown may differ from your TV. •• Your TV’s OSD (On Screen Display) may differ slightly from that shown in this manual. •• The available menus and options may differ from the input source or product model that you are using. •• New features may be added to this TV in the future.
Using the button Mounting on a table (Depending on model) You can simply operate the TV functions, pressing or moving the button. 1 Lift and tilt the TV into its upright position on a table. -- Leave a 10 cm (minimum) space from the wall for proper ventilation. [A Type] 10 cm 10 cm ENGLISH m 10 c 10 cm 10 cm Joystick Button 2 Connect the power cord to a wall outlet. CAUTION [B Type] •• Do not place the TV near or on sources of heat, as this may result in fire or other damage.
Mounting on a wall CAUTION ENGLISH Attach an optional wall mount bracket at the rear of the TV carefully and install the wall mount bracket on a solid wall perpendicular to the floor. When you attach the TV to other building materials, please contact qualified personnel. LG recommends that wall mounting be performed by a qualified professional installer. We recommend the use of LG’s wall mount bracket. The LG wall mount is easy to adjust or to connect the cables.
Connections (notifications) Other connections Connect various external devices to the TV and switch input modes to select an external device. For more information of external device’s connection, refer to the manual provided with each device. Available external devices are: HD receivers, DVD players, VCRs, audio systems, USB storage devices, PC, gaming devices, and other external devices. Connect your TV to external devices.
ENGLISH Slim remote control Magic remote functions (Depending on model) The descriptions in this manual are based on the buttons on the remote control. Please read this manual carefully and use the TV correctly. To replace coin batteries, turn the battery cover counterclockwise by using a coin. Then, take the battery cover. Insert and fix the battery (CR2032) with the facing forward. And, Put the battery cover on the remote control and turn it clockwise to close.
Registering magic remote How to register the magic remote How to deregister the magic remote B (HOME) Accesses the Home menu. * Shows the previous history. Displays the set-top box Home menu. -- When you are not watching via a set-top box: the display changes to the set-top box screen. Wheel (OK) Press the center of the Wheel button to select a menu. You can change programmes by using the Wheel button. Navigation buttons (up/down/left/right) Press the up, down, left or right button to scroll the menu.
ENGLISH Troubleshooting Specifications •• Cannot control the TV with the remote control. -- Check the remote control sensor on the product and try again. -- Check if there is any obstacle between the product and the remote control. -- Check if the batteries are still working and properly installed ( to , to ). •• No image display and no sound is produced. -- Check if the product is turned on. -- Check if the power cord is connected to a wall outlet.
Record the model number and serial number of the TV. Refer to the label on the back cover and quote this information to your dealer when requiring any service.
OWNER’S MANUAL EXTERNAL CONTROL DEVICE SETUP Please read this manual carefully before operating the set and retain it for future reference. www.lg.
2 KEY CODES ENGLISH ENG KEY CODES • This feature is not available for all models.
EXTERNAL CONTROL DEVICE SETUP 3 • Image shown may differ from your TV. Connect the USB to Serial converter/RS-232C input jack to an external control device (such as a computer or an A/V control system) to control the product’s functions externally. Note: The type of control port on the TV can be different between model series. * Please be advised that not all models support this type of connectivity. * Cable is not provided.
USB USB IN IN 4 EXTERNAL CONTROL DEVICE SETUP (PC) (PC) (TV) (TV) RS-232C IN (CONTROL SERVICE) • You need to purchase the phone-jack to RS-232 cable required for &the connection between the PC and the TV, which is specified in the manual. RS-232C IN (PC) * For other models, connect to the USB port. (PC) (CONTROL & SERVICE) * The connection interface may differ from your TV.
EXTERNAL CONTROL DEVICE SETUP 5 • Baud rate : 9600 bps (UART) • Data length : 8 bits • Parity : None ENGLISH ENG Communication Parameters • Stop bit : 1 bit • Communication code : ASCII code • Use a crossed (reverse) cable. Command reference list (Depending on model) COMMAND1 COMMAND2 DATA (Hexadecimal) 01. Power* k a 00 to 01 02. Aspect Ratio k c (p.7) 03. Screen Mute k d (p.7) k e 00 to 01 k f 00 to 64 06. Contrast k g 00 to 64 07. Brightness k h 00 to 64 08.
6 EXTERNAL CONTROL DEVICE SETUP ENGLISH ENG Transmission / Receiving Protocol Transmission [Command1][Command2][ ][Set ID][ ][Data][Cr] [Command 1] : First command to control the TV. (j, k, m or x) [Command 2] : Second command to control the TV. [Set ID] : You can adjust the [Set ID] to choose desired monitor ID number in option menu. Adjustment range in TV is 1 to 99. If [Set ID] value is selected to ‘0’, every connected set can be controlled.
EXTERNAL CONTROL DEVICE SETUP 7 01. Power (Command: k a) ►► To control Power *On or Off of the set. Transmission[k][a][ ][Set ID][ ][Data][Cr] Data 00 : Power Off 01 : *Power On Ack [a][ ][Set ID][ ][OK/NG][Data][x] ►► To Show TV is Power On or *Off Transmission [k][a][ ][Set ID][ ][FF][Cr] Ack [a][ ][Set ID][ ][OK][Data][x] * Similarly, if other functions transmit ‘FF’ data based on this format, Acknowledgement feedback presents status about each function. 02.
8 EXTERNAL CONTROL DEVICE SETUP ENGLISH ENG Data Min : 00 to Max : 64 Data Min : 00 to Max : 64 Ack [i][ ][Set ID][ ][OK/NG][Data][x] Ack [r][ ][Set ID][ ][OK/NG][Data][x] 09. Tint (Command: k j) * (Depending on model) ►► To adjust the screen tint. You can also adjust tint in the PICTURE menu. 14. Bass (Command: k s) Transmission [k][j][ ][Set ID][ ][Data][Cr] Data Red : 00 to Green : 64 Ack [j][ ][Set ID][ ][OK/NG][Data][x] ►► To adjust Bass. You can also adjust in the AUDIO menu.
EXTERNAL CONTROL DEVICE SETUP 6 5 0 0 0 0 0 0 1 Frequency 4 3 2 1 0 Step 0 1st Band 0 0 0 0 0 0(decimal) 1 2nd Band 0 0 0 0 1 1(decimal) 1 0 3rd Band ... ... ... ... ... ... 1 1 4th Band 1 0 0 1 1 19(decimal) 0 0 5th Band 1 0 1 0 1 20(decimal) Acknowledgement [v][ ][Set ID][ ][OK/NG][Data][x] * It depends on model, and can adjust when sound mode is EQ adjustable value. 19. Energy Saving (Command: j q) ►► To reduce the power consumption of the TV.
10 EXTERNAL CONTROL DEVICE SETUP ENGLISH ENG * Digital Antenna/Cable Data 00 : xx (Don't care) [Data 01][Data 02]: Major Channel Number Data 01 : High byte Channel Data Data 02 : Low byte Channel Data - 00 01 ~ 27 0F (Decimal: 1 ~ 9999) [Data 03][Data 04]: Minor Channel Number Data 03 : High byte Channel Data Data 04 : Low byte Channel Data Data 05 : Input Source (Digital) - 02 : Antenna TV (DTV) – Use Physical Channel Number - 06 : Cable TV (CADTV) – Use Physical Channel Number - 22 : Antenna TV (DTV)
EXTERNAL CONTROL DEVICE SETUP ►► To send IR remote key code. Transmission [m][c][ ][Set ID][ ][Data][Cr] 25. 3D(Command: x t) (only 3D models) (Depending on model) ►► To change 3D mode for TV. Transmission [x][t][ ][Set ID][ ][Data 00][ ][Data 01] [ ][Data 02][ ][Data 03][Cr] Data Key code - p.2. Ack [c][ ][Set ID][ ][OK/NG][Data][x] 23. Control Backlight (Command: m g) • For LCD TV / LED TV ►► To control the backlight.
12 EXTERNAL CONTROL DEVICE SETUP ENGLISH ENG 26. Extended 3D(Command: x v) (only 3D models) (Depending on model) 27. Auto Configure (Command: j u) (Depending on model) ►► To change 3D option for TV. ►► To adjust picture position and minimize image shaking automatically. It works only in RGB (PC) mode.
