OLED TV OLED55B7* OLED65B7* a AA 12 14 b 16 c X5 (M5 X L12) 20 d X4 (M4 X L12) : Depending on model / Abhängig vom Modell / Selon le modèle / In base al modello / En función del modelo / Dependendo do modelo / Afhankelijk van het model / Ανάλογα με το μοντέλο / Odvisno od modela / Típusfüggő / Zależnie od modelu / Závisí na modelu / V závislosti od modelu / În funcţie de model / В зависимост от модела / Sõltub mudelist / Priklauso nuo modelio / Atkarībā no modeļa / U zavisnosti od modela / Ovisno o
1 2 3 c 4 d a b 5 6 a + b 7
ANTENNA / CABLE IN HDMI IN HDMI IN/ARC USB IN LAN AUDIO OUT/ H/P OUT
LAN AUDIO OUT/ H/P OUT Satellite IN PCMCIA CARD SLOT OPTICAL DIGITAL AUDIO OUT
AV IN VIDEO L/MONO AUDIO R COMPONENT IN AUDIO VIDEO
1 2 3 4
0 1 A 2 E D B G F B A OLED55B7D-Z OLED55B7V-Z OLED65B7D-Z OLED65B7V-Z C C D E F G F 1229 764 254 708 48.6 18.6 17.2 1451 887 282 831 48.6 24.5 23.
*MFL69649022*
Safety and Reference Please read this manual carefully before operating your set and retain it for future reference. www.lg.com *MFL69727203* P/NO : MFL69727203 (1705-REV02) Printed in Korea Copyright ⓒ 2017 LG Electronics Inc. All Rights Reserved.
Warning! Safety instructions ENGLISH CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL. This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
•• Be careful in handling the adapter to prevent any external shocks to it. An external shock may cause damage to the adapter. •• Make sure the power cord is connected securely to the power plug on the TV. •• Install the product where no radio wave occurs. •• There should be enough distance between an outside antenna and power lines to keep the former from touching the latter even when the antenna falls. This may cause an electric shock.
ENGLISH •• Please follow the installation instructions below to prevent the product from overheating. -- The distance between the product and the wall should be more than 10 cm. -- Do not install the product in a place with no ventilation (e.g., on a bookshelf or in a cupboard). -- Do not install the product on a carpet or cushion. -- Make sure the air vent is not blocked by a tablecloth or curtain. This may result in fire.
•• Do not use any unapproved items to ensure the safety and product life span. •• Any damage or injuries caused by using unapproved items are not covered by the warranty. •• Some models have a thin film attached on to the screen and this must not be removed. •• When attaching the stand to the TV set, place the screen facing down on a cushioned table or flat surface to protect the screen from scratches. •• Make sure that the screws are fastened completely.
•• Do not apply excessive pressure to cause flexing/bending of frame chassis as it may damage screen. •• When handling the TV, be careful not to damage the protruding buttons. Basic functions Power On (Press) Power Off (Press and hold)1 ENGLISH •• Avoid touching the screen at all times, as this may result in damage to the screen. •• Do not move the TV by holding the cable holders, as the cable holders may break, and injuries and damage to the TV may occur.
Securing the TV to a wall (This feature is not available for all models.) Mounting on a wall 1 Insert and tighten the eye-bolts, or TV brackets and bolts on the back of the TV. • If there are bolts inserted at the eye-bolts position, remove the bolts first. 2 Mount the wall brackets with the bolts to the wall. Match the location of the wall bracket and the eye-bolts on the rear of the TV. 3 Connect the eye-bolts and wall brackets tightly with a sturdy rope.
•• To remove the stand, hold the top and bottom of stand, then pull it out while also lowering it as shown below. (Only OLED55E7*) ENGLISH 2 1 2 1 •• To install the wall mount, use the stand assembly screws to attach the Wall mount cover to the bottom of the product as shown in the figure below.
USB connection (Depending on model) Some USB Hubs may not work. If a USB device connected through a USB Hub is not detected, connect it directly to the USB port on the TV. ENGLISH STB PWR Other connections 1. @ 2 abc 3 def Connect your TV to external devices. For the best picture and audio 4 ghi and5 quality, connect the external device thejklTV with the HDMI cable. 6 mno Some separate cable is not provided.
v 6 mno 9wxyz 1 STB MENU ENGLISH GUIDE B 2 1 Control buttons ( ) Controls media contents. By zooming in on the selected area, you can view it in full screen. * You can zoom in on the area where the remote control is pointed. , , , These access special functions in some menus. * To use the button, press and hold for more than 3 seconds. (Depending on model) FOCUS LIVE ZOOM B (HOME) Accesses the Home menu. * Shows the previous history. Displays the set-top box Home menu.
B 2 1 B Adjusts the volume level. Scrolls through the saved programmes. (MUTE) Mutes all sounds. -- Pressing and holding the button accesses the Accessibility menu. (Voice recognition) Network connection is required to use the voice recognition function. 1 Press the voice recognition button. 2 Speak when the voice display window appears on the TV screen. (SEARCH)* Search for content such as TV programmes, movies and other videos, or perform a web search by entering text in the search bar.
Licenses Troubleshooting Supported licenses may differ by model. For more information about licenses, visit www.lg.com. Cannot control the TV with the remote control. ENGLISH •• Check the remote control sensor on the product and try again. •• Check if there is any obstacle between the product and the remote control. •• Check if the batteries are still working and properly installed ( to , to ). No image display and no sound is produced. •• Check if the product is turned on.
Abnormal Display Generated Sound •• “Cracking” noise: A cracking noise that occurs when watching or turning off the TV is generated by plastic thermal contraction due to temperature and humidity. This noise is common for products where thermal deformation is required. •• Electrical circuit humming/panel buzzing: A low level noise is generated from a high-speed switching circuit, which supplies a large amount of current to operate a product. It varies depending on the product.
(Depending on country) ENGLISH Television system DVB-S/S2 Channel coverage (Band) Maximum number of storable programmes External antenna impedance 14 950 ~ 2150 MHz Digital TV Analogue TV DVB-T DVB-T2 DVB-C DVB-S/S2 PAL/SECAM, B/G, D/K, I SECAM L DVB-C DVB-T/T2 46 ~ 890 MHz VHF III : 174 ~ 230 MHz UHF IV : 470 ~ 606 MHz UHF V : 606 ~ 862 MHz S Band II : 230 ~ 300 MHz S Band III : 300 ~ 470 MHz 6,000 2,000 75 Ω 46 ~ 862 MHz
OWNER’S MANUAL EXTERNAL CONTROL DEVICE SETUP Please read this manual carefully before operating the set and retain it for future reference. www.lg.
2 KEY CODES ENGLISH ENG KEY CODES • This feature is not available for all models.
EXTERNAL CONTROL DEVICE SETUP 3 • Image shown may differ from your TV. Connect the USB to Serial converter/RS-232C input jack to an external control device (such as a computer or an A/V control system) to control the product’s functions externally. Note: The type of control port on the TV can be different between model series. * Please be advised that not all models support this type of connectivity. * Cable is not provided.
USB USB IN IN 4 EXTERNAL CONTROL DEVICE SETUP (PC) (PC) (TV) (TV) RS-232C IN (CONTROL SERVICE) • You need to purchase the phone-jack to RS-232 cable required for &the connection between the PC and the TV, which is specified in the manual. RS-232C IN (PC) (PC) (CONTROL & SERVICE) * For other models, connect to the USB port. * The connection interface may differ from your TV.
EXTERNAL CONTROL DEVICE SETUP 5 • Baud rate : 9600 bps (UART) • Data length : 8 bits • Parity : None ENGLISH ENG Communication Parameters • Stop bit : 1 bit • Communication code : ASCII code • Use a crossed (reverse) cable. Command reference list (Depending on model) COMMAND1 COMMAND2 DATA (Hexadecimal) 01. Power* k a 00 to 01 02. Aspect Ratio k c (p.7) 03. Screen Mute k d (p.7) k e 00 to 01 k f 00 to 64 06. Contrast k g 00 to 64 07. Brightness k h 00 to 64 08.
6 EXTERNAL CONTROL DEVICE SETUP ENGLISH ENG Transmission / Receiving Protocol Transmission [Command1][Command2][ ][Set ID][ ][Data][Cr] [Command 1] : First command to control the TV. (j, k, m or x) [Command 2] : Second command to control the TV. [Set ID] : You can adjust the [Set ID] to choose desired monitor ID number in option menu. Adjustment range in TV is 1 to 99. If [Set ID] value is selected to ‘0’, every connected set can be controlled.
EXTERNAL CONTROL DEVICE SETUP 7 01. Power (Command: k a) ►► To control Power *On or Off of the set. Transmission[k][a][ ][Set ID][ ][Data][Cr] Data 00 : Power Off 01 : *Power On Ack [a][ ][Set ID][ ][OK/NG][Data][x] ►► To Show TV is Power On or *Off Transmission [k][a][ ][Set ID][ ][FF][Cr] Ack [a][ ][Set ID][ ][OK][Data][x] * Similarly, if other functions transmit ‘FF’ data based on this format, Acknowledgement feedback presents status about each function. 02.
8 EXTERNAL CONTROL DEVICE SETUP ENGLISH ENG Data Min : 00 to Max : 64 * (Depending on model) Ack [i][ ][Set ID][ ][OK/NG][Data][x] 09. Tint (Command: k j) ►► To adjust the screen tint. You can also adjust tint in the PICTURE menu. Transmission [k][j][ ][Set ID][ ][Data][Cr] Data Red : 0 0 to Green : 64 Ack [j][ ][Set ID][ ][OK/NG][Data][x] 10. Sharpness (Command: k k) ►► To adjust the screen sharpness. You can also adjust sharpness in the PICTURE menu.
EXTERNAL CONTROL DEVICE SETUP 0 0 5th Band 1 0 1 0 0 20(decimal) Acknowledgement [v][ ][Set ID][ ][OK/NG][Data][x] * It depends on model, and can adjust when sound mode is EQ adjustable value. 19. Energy Saving (Command: j q) ►► To reduce the power consumption of the TV. You can also adjust Energy Saving in PICTURE menu.
10 EXTERNAL CONTROL DEVICE SETUP ENGLISH ENG Number - 22 : Antenna TV (DTV) – Don’t Use Physical Channel Number - 26 : Cable TV (CADTV) - Don’t Use Physical Channel Number - 46 : Cable TV (CADTV) – Use Major Channel Number Only (One Part Channel) Two bytes are available for each major and minor channel data, but usually the low byte is used alone (high byte is 0). * Tune Command Examples: 1. Tune to the Analog cable (NTSC) channel 35.
EXTERNAL CONTROL DEVICE SETUP ►► To select input source for main picture. Transmission [x][b][ ][Set ID][ ][Data][Cr] Data 00 : DTV 01 : CADTV 02 : Satellite DTV 10 : ATV ISDB-BS (Japan) 03 : ISDB-CS1 (Japan) 04 : ISDB-CS2 (Japan) 11 : CATV O 01 X X X 02 X X X 03 X O O [Data03][x] [t][ ][Set ID][ ][NG][Data00][x] 21 : AV2 41 : Component2 90 : HDMI1 92 : HDMI3 91 : HDMI2 93 : HDMI4 26. Extended 3D(Command: x v) (only 3D models) (Depending on model) ►► To change 3D option for TV.
12 EXTERNAL CONTROL DEVICE SETUP ENGLISH ENG 27. Auto Configure (Command: j u) (Depending on model) ►► To adjust picture position and minimize image shaking automatically. It works only in RGB (PC) mode.
