DLP PROJECTOR Thank you for Please read this user's guide the DLP purchasing guide to Projector. ensure correct use of the device. Save this user's for future reference. OUTLINE This DLP Projector can display various computer signals and NTSC/PAL/SECAM video signals. 1. High Brightness 2. High 3. Compact Size, Resolution 4. Durable 5. RGB Weight for Portability Magnesium Alloy Body input 6. One Touch 7.
Copyright ⓒ 2002. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of the company.
Table of Contents Introduction...........................1 SafetyInstructions................................................1 FCCStatement...................................................2 ShippingContents................................................3 OptionalAccessories...........................................3 ProjectorDescription.............................................4 Projector.....................................................4 ExternalControlPanel......................................
iv DLP Personal Projector
INTRODUCTION Caution TO PREVENT SHOCK, DO NOT OPEN THE CABINET. NO USER --SER- VICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. PLEASE READ THIS USER'S GUIDE BEFORE YOU OPERATE YOUR PROJECTOR. SAVE THIS USER'S GUIDE FOR FUTURE REFERENCE Safety 1. . Instructions Read this user's guide before you operate your projector and save it for future reference. 2. The lamp becomes extremely hot during operation.
Do not touch the ventilation ? grill when the projector Save this user's in operating and guide: The information contained in maintaining your personal projector. is under operation. this manual will assist you FCC Statement FCC STATEMENT radio - CLASS A: This equipment generates, uses and can radiate energy, and if not installed and used in accordance with the instruction manual, may cause interference to radio communications.
Shipping Contents The Projector is shipped with the cables required for connection to standard PC laptop computers. Carefully unpack and verify that you have all the items shown below. If any of these items are missing, please contact personnel at the place of purchase. or Quick Start Guide User's Guide Projector User 's Guide Quick Start Guide Remote Control 3-2 Converter HDTV Cable Batteries 220V Audio Cable VGA Cable Optional Deluxe Soft India Power USB Cable (S.
Projector Description Projector 76 8 1 9 12 5 13 2 3 4 1 External control (see next panel 101114 15 11 Audio/ Video connector 12 Computer Audio 13 USB page) lens 2 Projection 3 Front 4 IR remote sensor 14 S-Video 5 Ventilation grill 15 RS-232C control 16 Rear 17 Kensington adjuster IN connector mouse jack port feet 6 Speaker 7 Projection 8 Computer signal input 18 AC power cord inlet 9 Computer signal output 19 Main power switch YPBPR connector 20 L
External Control Panel 4 3 5 6 7 2 1 8 9 1 Power 7 Presses the Power the projector on or key Source Selects to turn signal sources from among PC, YPBPR, Video and S- off. Video. 2 Auto Automatically determines the best picture settings for current received signals. 3 Left/ 5 Keystone + 46 menus Lamp Indicator will light up lamp needs service, or replacement. See cooling "Lamp Information" on page 20 for 9 on-screen menu +/- hot as Temp detailed information.
Adjuster The projector is equipped adjust its tilt angle. 1. Lift the 2. The Projector projector with 2 quick-release adjuster feet. up and press the adjuster will drop into position adjuster Push the buttons to button to release the Features The projector integrates high-performance optical engine projection friendly design to deliver high reliability and ease of use. The ? ? ? ? ? ? ? ? ? adjuster. and be locked.
Remote Control Description The remote control sensors are distance between the sensor located in the front/ back of the projector. The and the remote control should not exceed 6 meters. LED Power Laser Pointer Source Menu Exit 3 Left/ 4 Right/ Keystone Keystone - + Blank Auto Mouse Pad L-Mouse/ R-Mouse L R Zoom in/ out By pressing Mouse ZOOM IN +, the picture will be magnified.
Installing 1 or Replacing Batteries Push and slide the Install batteries 2 indicated battery as compartment lid in the the direction inside the by diagram compartment. 3 Position the lid over the compartment and snap it back into place. Caution Avoid excessive heat and humidity. There may be danger of an explosion if incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer.
INSTALLATION Screen Size Place the desired projector size picture at the required (see the table distance from the Screen Size (Max.) A. Width C. 30.4 61.8 46.3 100 60.8 123.7 92.7 200 91.2 185.3 138.9 300 121.5 247.0 185.2 151.9 308.7 231.6 182.3 370.5 277.9 212.8 432.2 243.1 494.0 273.5 303.9 The ? ? Screen Size (Min.) D. Height (cm) 24.9 50.7 38.0 49.9 101.3 76.0 74.7 151.9 113.9 400 99.7 202.5 151.9 500 124.6 253.2 189.9 600 149.5 303.
Please refer to "Menu System" on page 13 for information on the HDTV OSD selections. Connecting to Various It few seconds to connect your projector to your or other systems. However, a Mac adapter only takes a Equipment computer, VCR, accessory) is needed for connection to Macintosh desktop or notebook (an optional computers.
OPERATION Start Up 1. Plug the power cord into 2. Turn on 3. a wall socket. the main power switch. Press POWER to start the unit. The back-lit POWER and stays green when the power is turned 4. Switch on all connected flashes green Remote Control Projector (When the power is turned off, projector can be re-started.) key on. there is a 120-second cooling period before the equipment.
Digital Keystone Keystoning Correction refers to the situation where the at either the projected image is noticeably bottom. To correct this, press KEYSTONE +/- (hot key) top control panel of the projector or on the remote control, and then adjust the bar labeled image. or Keystone, Press - as to correct needed. Press keystoning + to correct keystoning image.
Source Selection When several input sources are selection from the control panel available, press the SOURCE key to make of the projector or a the remote control. Remote control Projector Source Auto Menu Source System Press Menu for the main menu, and then press Press Menu again 3or 4 to select a sub-menu. to select items in the sub-menu.
1. Display Menu FUNCTION DESCRIPTION Corrects any keystoning of the image. Keystone - the Adjusts brightness of the image. Brightness Adjusts the degree the image. of difference between dark and light in Contrast to avoid the Adjusts occurrence of flicker. Phase *This function is not available when the input mode is Video or is Video or S-Video. to fit in the desired Adjusts H Size image size. *This function is not available when the input mode S-Video.
2. Image Menu FUNCTION Ratio DESCRIPTION Users have 2 1. 4:3 options for the image ratio. 2. 16:9 Adjusts the horizontal Adjusts the vertical Adjusts the color position of the projected image. H Position positon of the projected image. V Position Color Temp Information preference. information will be shown: 1.NTSC 2. PAL 3.SECAM *The default Adjusts Sharpness to fit your Shows the current resolution. System System temperature the setting image for System is Auto.
3. Source Menu FUNCTION DESCRIPTION 1. Default Mirror 3. Rear screen projection 2. Ceiling 4. Ceiling screen Source Selects the input source Adjusts the volume level. Adjusts the treble level. Adjusts the bass level. Volume Treble Bass On Mute 16 DLP Personal projection mounted and rear- projection from among PC, YPBPR, Video and S- Video.
4. Control Menu FUNCTION DESCRIPTION sets the Language language for the OSD control menus. Language Use the 3 / 4 key to select the desired language from English, French, German, Italian, Spanish, Russian, Polish, Korean, Simplified Chinese and Traditional among Chinese. OSD Pos. Selects OSD a desired OSD position. OSD Time Sets the length of time the OSD will remain active after the last time you pressed the button. The range is from 5 to 60 seconds in 5-second increments.
5. PIP Menu These functions source is Video are or available when the only FUNCTION PIP Source mode is PC and the PIP input S-Video. DESCRIPTION Selects the Enables for the PIP. source of the 3 use / 4 key to scroll alternatives: Off, Small, Medium, through Large. the four PIP Size Selects a desired H. Position Adjusts the horizontal V. Position Adjusts the vertical position for the PIP. PIP Position Options tions ness of the PIP of the PIP image. image.
Shutdown 1. Press POWER and projector, a warning message again. will appear. To turn off the press POWER Projector Remote Control 2. The fan will continue to 3. Turn off the ON/OFF switch. 4. Disconnect the power cord from the wall socket. run for approximately two minutes. Caution ? ? Please do not unplug the power cord before POWER is shut down or during the two-minute cooling process.
MAINTENANCE Lamp Information Use and Replacement When the of the Lamp Indicator Lamp lights up red or a message appears suggesting the time of lamp replacement, please install a new lamp or consult your dealer. An old lamp could cause a malfunction in the projector and in rare instances may even explode. Lamp LED Indicators Lamp Life Indicators The Lamp is not properly attached Lamp temperature high When the LED lights up red, it is warning you that lamp uage has exceeded 1500 hours.
Caution To reduce the risk of 45 minutes before To reduce the risk of nents, use severe replacing burns, allow the projector the lamp. to cool for at least injuries to fingers and damage to internal comporemoving lamp glass that has shattered into caution when sharp pieces. To reduce the risk of injuries to fingers and/or compromising image quality by touching the lens, do not touch the empty lamp compartment when the lamp is removed. This lamp contains mercury.
TROUBLESHOOTING Common Problems & Solutions PROBLEMS TRY THESE SOLUTIONS ? Make ? NO POWER Make ? ? ? ? TRAPEZOID ? the power cord is inserted snuged into the power the power switch to the position "I". Wait two minutes after the projector is turned off before Toggle the ? IMAGE ? ? ? ? Adjust the ? ? CONTROL DOES NOT WORK 22 and contrast. brightness Remove the lens cap. Reposition the unit to improve its angle on the screen.
Status Messages On-Screen Description Messages SEARCHING ACQUIRING SIGNAL OUT OF RANGE Projector is for searching input. Projector has identified the input signal and ning the auto image adjustment function. Input signal frequency exceeds the is run- projector's range. LAMP WARNING - CHANGE LAMP AND RESET LAMP The lamp Install has been in a new lamp for operation for 1400 hours. optimal performance. TIMER! OUT OF LAMP USAGE TIME.
SPECIFICATIONS Projector Specifications Technical Note: All Specifications specifications are to subject change without notice. General Product Model name name Personal Projector RD-JT40 1024X768 XGA RD-JT41 800X600 SVGA Optical Display system 1-CHIP DMD Lens F/Number F/2.6 Lamp 210W NSH lamp Electrical Power supply AC100 Power consumption 330 W 240V, 3.
Timing Chart Resolution H Sync (kHz) V Sync (Hz) 640x350 31.5 70.1 640x400 37.9 85.1 720x400 31.5 70.0 Remark VESA 720x400 37.9 85.1 VESA 640x480 31.5 60.0 VESA 640x480 37.9 72.8 VESA 640x480 35.0 66.7 Macintosh 640x480 43.3 85.0 VESA 800x600 35.2 56.3 VESA 800x600 37.9 60.3 VESA 800x600 48.1 72.2 VESA 800x600 46.9 75.0 VESA 800x600 53.7 85.1 VESA 832x624 49.7 74.5 Macintosh 1024x768 48.4 60.0 VESA 1024x768 56.5 70.1 VESA 1024x768 60.
DIMENSIONS 308 238 95 Unit: 26 DLP Personal Projector mm