LCD PROJECTION TV OWNER'S MANUAL Please read this manual carefully before operating your set. Retain it for future reference. Record model number and serial number of the set. See the label attached on the back information to your dealer when you Model number : Serial number : P/NO : 3828VA0401A (MB03CA, 100E TX) a and quote this require service.
Contents Installation 3 Location and function of controls Remote control handset Battery installation Front panel / Rear panel 4 Basic operation On and off / Programme selection Volume adjustment / Quick view / Mute function On screen language selection (option) 8 On 9 screen menus Menu selection SETUP menu Auto programme tuning Manual programme tuning Fine Tuning / Programme edit Calling the programme table 10 PICTURE 15 menu PSM(Picture Status Memory) Picture adjustment AUDIO menu SSM (Soun
Installation Power This set operates on an AC mains supply, the voltage is as indicated on the label on the back cover. Never apply DC power to the set. In the event of thunderstorms ial and mains or powercuts, please pull out the aer- plugs. Warning To prevent fire moisture. or shock hazard, do not expose the set to rain or Service Never remove the back high voltage properly, unplug it very cover of the set as this can expose you to and other hazards.
Location and function of controls All the functions Some functions panel can can be controlled with the remote control handset. also be adjusted with the buttons on the front of the set. Remote control handset Before you use the remote control handset, teries. See the next page. POWER 1 1. MULTIMEDIA TV/AV 2 MUTE 2. SLEEP 3 PIP TEXT 4 3. PR- PR+ SWAP INPUT 5 MENU PR 4. CANCEL/EXIT OK VOL 7 PR 123 456 8 7 8 9 PSM 0 SSM POSITION SIZE STILL INDEX TIME REVEAL 5. 6.
Location and function of controls 12. TV/AV selects the remote switches the set 13. SLEEP sets the sleep on operating mode. from standby. timer. POWER 14. TELETEXT BUTTONS These buttons are used for teletext. For further details, see the 'Teletext' section. MULTIMEDIA TV/AV 12 MUTE 13 15. CANCEL/EXIT Clears all on-screen SLEEP PIP displays and returns to TV viewing TEXT 14 from any menu. PR- PR+ SWAP 16. SSM (Sound Status Memory) recalls your preferred sound setting.
Location and function of controls Front panel Lamp indicator, operation indicator, and temperature indicator, trols reveal the operating status of the LCD projection TV. located below the front panel con- ON/OFF TV/AV TV/AV 2 10 MENU MENU OK VOL ON/OFF PR OK 34 1. MAIN POWER (ON/OFF) switches the set on or off. 2. TV/AV selects the remote operating mode. switches the set on from standby. VOL PR 5 6 789 1 7. OPERATION INDICATOR (Refer 8. LAMP INDICATOR to 9.
Location and function of controls Rear panel A/V 3 INPUT S-VIDEO S-VIDEO INPUT SOCKET VIDEO L/MON AV3 INPUT SOCKET AUDIO A/V3 NPUT S-VDEO V DEO L/MON R AUDO R SIDEAV SIDE A/V NTN L 5Ω R1 DTV (GA 48p 2p 10i U P G R P A O D R T G12 Y PB PR PDT GA 48p 2p 10i RB2 DTDD 4i48p2/1i) ANT IN L L 75Ω PC/DTV INPUT SOCKETS AERIAL SOCKET PC/DTV INPUT UP GRADE UPGRADE PORT This port is used upgrade PO RT to the software RGB 576i/480i 576i/480i (XGA/ 576p/ 480p/ 720p/ 1080i) 576p/480p
Basic Operation On and off Before turning the set on, be sure that the main power switch the set is pushed on. When the main switch is pushed on, the LED will be lit up red. This mode is Stand-by. If the set is in stand-by mode, press the POWER, Δ / Ε, TV/AV, MULTIMEDIA or NUMBER button on the remote control handset to turn it on fully. The LED will blink orange for a while and then lit up green when the power is successfully on. To turn the set off, press the power button on the remote control handset.
On Screen Menus The dialogue between you and your set takes place required for the operating steps are also displayed. on screen with an operator menu. The buttons Menu selection 1. Press the MENU button and then Δ / Ε button to 2. Press the Γ button and then the Δ / Ε button to select 3. Repeatedly press Note : On some display each a menu the MENU button to return to normal TV menu. item. viewing. models, the Language will not display.
SETUP Menu SETUP SETUP Γ Auto programme Manual programme PICTURE Programme edit Up to 100 TV stations can be stored in this set by programme numbers (0 to 99). Once you have preset the stations, you will be able to use the Δ / Ε or NUMBER buttons to scan the stations you programmed. Stations can be tuned using automatic or manual modes. Note In : some models up to 200 TV stations Auto programme AUDIO can be stored. tuning All stations that can be received are stored by this method.
SETUP Menu Manual programme tuning Manual programme lets you manually tune and arrange the stations in whatever order you desire. Also you can assign a station name SETUP Γ Auto programme Manual programme PICTURE with five characters to each programme number. Programme edit AUDIO AUDIO 1. Press the MENU button and then Δ SETUP / Ε button to select the menu. TIME 2. Press the Γ button and then Δ 3. programme.
SETUP Menu Assigning a station name 1. Repeat the 'Manual programme tuning' steps SETUP Γ Auto programme Manual programme PICTURE Programme 2. 3. edit 4. AUDIO 5. 6. TIME 1 to 3. Press the Γ button to select Name. Press the Δ button. You can use a blank, +, -, the numeric 0 to 9 and the alphabet A to Z. With the Ε button you can select in the opposite direction. Select the next position by pressing the Γ button and then take your choice of the second character, and so on. Press the OK button.
SETUP Menu Programme edit This function enables you to delete or skip the stored programmes. Also you can move some stations to other programme numbers or copy a blank station data into the selected programme number. 1. 2. 3. Press the MENU button and then Δ / Ε button to select the SETUP menu. Press the Γ button and then Δ / Ε button to select Programme edit. Press the Γ button to display the Programme edit menu.
SETUP Menu Calling the programme table You can check the programmes stored in the memory the programme table. by displaying table Press the LIST button to display the Programme table The programme table appears on the screen. Displaying programme C1 menu.
PICTURE Menu PSM 1. 2. 3. (Picture Status Memory) Press the MENU button and then Δ / Ε button to select the PICTURE menu. Press the Γ button and then Δ / Ε button to select PSM. Press the Γ button and then Δ / Ε button to select a picture setting on the PSM pull-down menu.
AUDIO MENU SSM You SSM SETUP SETUP Internal speaker Γ select your or grammes. Balance AUDIO preferred sound setting; Dolby Virtual, Flat, Speech and you can also adjust the sound frequency of equalizer, balance. If you switch AVL to on, the set automatically keeps on an equal volume level even if you change procan Music, Movie, AVL PICTURE (Sound Status Memory) 1. Equalizer 2. 3. TIME Press the MENU button and then Δ / Ε button to select the AUDIO menu.
AUDIO MENU Speaker adjustment You 1. 2. 3. can adjust internal speaker status. Press the MENU button and then Δ / Ε button to select the AUDIO menu. Press the Γ button and then Δ / Ε button to select Internal PICTURE speaker. AUDIO Press the Γ button and then Δ / Ε button to select On, Center or Off on the Internal speaker pull-down menu.
AUDIO MENU Equalizer (option) 1. SSM SETUP SETUP AVL PICTURE Internal speaker Balance AUDIO Γ 2. 3. Press the MENU button and then Δ / Ε button to select the AUDIO menu. Press the Γ button and then Δ / Ε button to select Equalizer. Press the Γ button in Equalizer to display the Equalizer sub menu. Equalizer SETUP SETUP TIME SSM AVL PICTURE PICTURE Internal speaker SPECIAL Balance AUDIO AUDIO Equalizer TIME TIME 120 500 1.5k 5k 10k (Hz) SPECIAL SPECIAL Φ Prev. 4. 5. 6. 7.
AUDIO MENU Stereo/Dual reception When a programme is selected, the sound information for the station appears after the programme number and station name disappear. Broadcast On Screen Mono MONO Stereo STEREO Dual DUAL I Display Mono sound selection In stereo reception if the stereo signal is weak, you can switch to by pressing the I/II button twice. In mono reception the depth of sound is improved. To switch back to stereo, press the I/II button twice again.
TIME MENU Auto SETUP SETUP Auto sleep Sleep timer 1. PICTURE 2. 3. AUDIO TIME sleep If there is minutes. no input signal, the set will turn off automatically after 10 Press the MENU button and then Δ / Ε button to select the Time menu. Press the Γ button and then Δ / Ε button to select Auto sleep. Press the Γ button and then Δ / Ε button to select On or Off. Γ SETUP SETUP SPECIAL Auto sleep Sleep timer Γ Off On PICTURE AUDIO AUDIO TIME TV/AV SPECIAL SPECIAL Φ Prev. SLEEP 4.
SPECIAL MENU Main Picture Source Selection Inputs can be set for TV cassette recorder or (VCR), AV mode. AV mode is used when or other equipment a video is connected to the set. Main SETUP PIP PICTURE input input Child lock ARC Note : When a VCR is connected via the aerial socket the set is used in TV mode. See the 'Connection of external AUDIO Language equipment' section. TIME 1. Press the MENU button and then Δ / Ε button to select the SPECIAL menu. 2.
SPECIAL MENU Child Lock Main SETUP SETUP PIP PICTURE input input The TV can be set that the remote control handset is needed to so control it. This feature can be used to prevent unauthorized view- ing. Child lock Press the MENU button and then Δ 1. ARC AUDIO SPECIAL Language / Ε button to select the menu. Press the Γ button and then Δ / Ε button to select Child lock. Press the Γ button and then Δ / Ε button to select On or Off. 2. 3.
Picture In Picture Option : PIP (Picture in Picture) displays a picture within a (PIP) Function picture. On and off Press the PIP button to switch on the sub picture. Press CANCEL/EXIT button to switch it off. Each press of PIP button button changes the screen shown below. display as PIP PR- Note ture : When the sub picture quality might get poor.
Teletext (option) Teletext (or TOP text) is an optional function, therefore only with the teletext system can receive the teletext broadcast. a set free service broadcast by most TV stations which gives information on news, weather, television proshare grammes, prices and many other topics. Teletext is a up-to-the-minute TV/AV TEXT The teletext decoder of this TV can support the SIMPLE, TOP and FASTEXT systems.
Teletext TOP text The user (option) (option) guide displays the bottom of the four fields-red, green, yellow and blue at The yellow field denotes the next group screen. and the blue field indicates the next block. Block / group / page selection 1. With the blue button you can progress from block to block. 2. Use the yellow button to proceed to the next group with auto- TV/AV matic overflow to the next block. 3.
Teletext Special (option) teletext functions REVEAL Press this button to display concealed information, such as puzzles. again to remove the information from the solutions of riddles Press this button or display. SIZE Selects double height text. enlarge the top button again to enlarge Press this button to Press this page. Press this button PR again half of the page. the bottom half of the to return to the normal display.
Connection of PC PC in socket 1. Connect the cable from the monitor output socket of the input socket of the set. signal ANT IN L L 75Ω PERSONAL COMPUTER to the PC PC/DTV INPUT COMPONENT COMPONENT INPUT 1 INPUT 2 U 2. Connect the audio cable from the PC to the PC/DTV INPUT AUDIO sockets G R A D E P O the back of the set. on P RGB 576i/480i (XGA/ 576p/ 480p/ 720p/ 1080i) 576p/480p 720p/ Press the TV/AV or 576i/480i 576p/480p 720p/ 1080i Y T (L) AUDIO 3.
Connection of PC RGB-PC Mode Main SETUP SETUP PIP PICTURE input 1. iInput ARC AUDIO Press the MENU button and then Δ / Ε button to select the SPECIAL Child lock Language (option) menu. 2. Press the Γ button and then Δ / Ε button to select Main 3. Press the Γ button and then Δ / Ε button to select RGB-PC. RGB-PC Input. Adjust TIME SPECIAL H-Position 0 V-Position 0 H-Size 0 Γ V-Size 0 Phase -15 ΔΕ Select 4. picture appropriate adjustments.
Connection of external You can connect additional equipment, such as equipment VCRs, camcorders ANT IN etc. to your set. L L 75Ω PC/DTV INPUT Here shown may be somewhat different from your set. COMPONENT COMPONENT INPUT 1 Aerial socket UP RGB GRADE (XGA/ 576p/ 480p/ 720p/ PO RT 1080i) INPUT 2 576i/480i 576i/480i 576p/480p 720p/ 576p/480p 720p/ 1080i 1080i Y (L) S-VIDEO PB AUDIO (R) A/V 1 INPUT PR A/V 2 INPUT MONITOR OUT AUDIO CENTER MODE IN 1.
Connection of external Audio/Video input ANT IN L L 75Ω PC/DTV INPUT RGB (XGA/ 576p/ 480p/ 720p/ RADE P sockets (option) COMPONENT COMPONENT INPUT 1 UPG equipment INPUT 2 576i/480i 576i/480i 576p/480p 720p/ 576p/480p 720p/ 1080i 1080i 1. Connect the audio/video out sockets of the VCR to audio/video 1080i) O R T in sockets of the set. Y (L) S-VIDEO PB AUDIO (R) A/V 1 INPUT PR A/V 2 INPUT MONITOR OUT AUDIO CENTER MODE IN VA A U R I A O DI BL E O 2.
Troubleshooting check list Symptoms No picture, no sound Sound OK, poor picture Picture OK, poor sound Picture blurred Lines or streaks in Poor picture reception on some channels No colour Poor colour Remote control does not work Poor brightness Strange sound from inside the monitor Check these items and try to adjust these The mains plug-(plugged in and switched on) Is the TV switched on? Try another channel (weak signal) Check aerial (plugged into Check aerial (broken lead?)
