Table of contents Information for your How to use the cleaner cleaning Operation Adjusting How to ........................................................................................... head and the dust chamber Emptying Accessory Nozzles .................................................... ................................................................................. ........................................................................................................
Information for your safety Please read all the following information, which contains important instructions for the safety, the use and the maintenance of the appliance. appliance complies with the following EC Directives: -73/23/EEC, 93/68/EEC-Low Voltage Directive-89/336EEC -EMC Directive. Never allow children to use the appliance unsupervised. Do not use the appliance If the mains lead is damaged or faulty.
How to Fit the use Assembling large cleaning Cleaner head onto the end of the tube. 2 1 Nozzle outlet 1 The 2 Push position telescopic nozzle outlet. 4 head tube into 2 Telescopic Push tube telescopic tube into hose handle until catch clicks.
Attachment Point 3 Button Head Flexible Hose 3 Connecting the flexible hose Push the end of the head into the attachment To remove pull on on the flexible hose the vacuum the flexible hose from the cleaner, press then point on the button situated cleaner. vacuum on the head, forward.
How to Open use Using the cleaning the accessory Fit the cleaning cover and pull head and Accessory Nozzles out accessory you want. head onto the end of the tube. 2 1 3 1 Upholstery Nozzle Dusting brush & Crevice Tool frames, furniture outlines, books and other mattresses, etc. uneven The thread collectors Crevice Tool is for to pick up the threads and lint.
1 2 3 4 5 6 Spring Head 4 latch 6 5 Pedal 4 Large cleaning ? head position heads equipped pedal which allows you to position according to the type 5 its a punch Refer to The 2 with Sani Page nozzle 12~14. 6 Adjusting the telescopic tube length Telescopic tube alter ? Pull out tube to required length. of ? Release latch. spring floor to be cleaned. ? Hard floor position(tiles, parquets floor) pedal to lower brush.
How to use Emptying the dust chamber Button Dust chamber The dust chamber needs full by emptying MAX which is marked on when the dust is the dust chamber. ? Turn off the ? Your appliance and unplug it. appliance is equipped with both the dust chamber and the motor filter. Press the button of the ? cover and into the tank mount until it will go 8 pull the dust chamber forward. Remove the dust chamber cap and empty the dust chamber.
Operation Switch button Hose handle 2 1 3 POWER CONTROL STOP AUTO MIN MAX BOOSTER Key pad Cord reel button Light 1 Adjusting ? ? Adjust power with the power control switch in the handle. If you press the key that you want, the light which is located on body is on ? the power level In 2 How to ? of auto, the power and light by the amount of dust. in and 3 use Pull out the mains lead to the desired length and plug ? is controlled ? To cleaner.
How to use Cleaning the motor filter/Air cleaner The motor filter is situated under the tank cap and you can use it WARNING! permanently. Each time the light and brush and then is on and replace off, clean the it in the motor filter with water vacuum cleaner. Press the button of cover and pull the dust chamber forward. Open the chamber cap. Separate the motor filter by rotaing it counter-clockwise. Clean the motor filter with the brush under a running tap. ?Dryitinshadeforaday.
Cleaning Cleaning the dust chamber the exhaust filters Plate dust chamber 2 1 Filter cover Wheel 3 Tank cap 1 Open the tank cap. 2 Remove two plates from ? the dust chamber. ? ? The exhaust filter is washable HEPA filter. so you To change can use it permanently. the exhaust the filter cover on the filter cover the filter, remove body by rotating counter-clockwise. Pull out the exhaust filter. Clean it with water.
User's guide for sani punch nozzle vacuum Features How to This nozzle Follow the directions below for proper picks up even dust inside through beating. The bottom part can be separated to be cleaned. Since the bottom does not stick to the surface, vacuuming is easy. use Assembly Connect the nozzle to the use. telescopic tube. Use Set the suction power control switch to MAX POWER before vacuuming.
This Sani Punch nozzle is for effective Effective cleaning of beds and blankets to remove mites and dust. cleaning Bed & blanket Bulky When using on Lay out the blanket and vacuum it on the bed the bed & heavy When blanket Light using on It is easier to clean by pushing blanket & sheet the floor light blanket or sheet the nozzle to the direction of the arrow. To increase lay on cleaning efficiency for light blankets, top of a bulky blanket and then clean.
User's guide for sani For simple cleaning of the vacuum and attach the crevice tool to Top punch vacuum nozzle Cleaning Vacuum Nozzle for nozzle, detach the Sani Punch nozzle from the telescopic tube vacuum dust. Bottom Since the vibrator inside is composed of precision parts, never disassemble the body. foreign objects clog the air sunction part on top of the vacuum nozzle. Since removal of the punch bar may cause performance problems, do not warp or remove it.
Follow the instruction below for not soak the entire (Do body through washing. of the vacuum nozzle in water, it may cause the vibrator to malfunction) Bottom 2 1 plate 3 Punch bar Bottom 4 plate 6 5 Punch bar 1 Press the button rear side of the nozzle to bottom on 2 the all the soiled Wipe of the vacuum separate the body with a parts 3 nozzle vacuum Wash the removed bottom plate with water and dry it. cloth. plate.
What to do if your Check that the appliance is appliance correctly plugged in and that the electrical socket is What to do when the suction the appliance and working. performance reduces? it. ? Stop ? Check that the ? Check that the dust chamber is not full. ? Check that the ? Check that the exhaust filter is not blocked. unplug does not work tubes, flexible hose and cleaning tool. light is not on Empty if necessary. because of motor filter's blockage. Clean the filter. .
Note 17
Note 18
P/No.