V-C7760NT V-C7760NE
Table of contents Information for Your Safety......................................................................................3 How to Use.................................................................................................................4 Assembling Using the Emptying the Cleaner ........................................................................................................4 cleaning head and Accessories...................................................................
Information for Your Safety Please read all the following information, which contains important instructions for the safety, the use and the maintenance of the appliance. This appliance complies with the following EC Directives: -73/23/EEC, 93/68/EEC-Low Voltage Directive-89/336EEC -EMC Directive. Do not use the appliance If the power cable is damaged or faulty. If the power cable is damaged, it must be replaced by an approved LG Electronics Service Agent to avoid a hazard.
Assembling Cleaner 2 Fit the large cleaning head onto the end of the tube. Spring latch Telescopic tube 1 Nozzle outlet Large cleaning head Push the head onto the Telescopic ? telescopic tube. Press the tube spring latch to release. ? Pull out the tube to the desired length. ? ? Release spring latch to lock the tube in position. Push telescopic tube into hose handle until catch clicks.
Head Flexible Hose Attachment Point Button 3 Connecting the hose to the cleaner Push the end of the head into the attachment To remove pull on the flexible hose the vacuum the flexible hose from the cleaner, press then point on on the button situated the head out of the vacuum cleaner. vacuum on the head, cleaner.
Using the Tear the cleaning head and vinyl bag and pull Accessory Nozzles out accessories. Attach the accessory holder into the side hole of And then, Fit the Dusting body. Brush & Crevice Tool and Upholstery Nozzle onto the accessory holder. Fit the accessory onto the end of the tube. Upholstery nozzle Dusting brush & Crevice tool 1 2 Upholstery Nozzle Dusting Upholstery Nozzle is for vacuuming upholstery, frames, furniture frames, books and other mattresses, etc. hard surfaces.
1 2 (Refer to Page 6) 3 5 4 3 (See below) (See below) (Refer to Page 10) 4 Pedal NE Head Spring latch Spring latch 3 Large cleaning head 4 Elbow tube (V-C7760NE) ? ? ? The 2 position cleaning head is equipped with a pedal which allows you to alter the brush position according to the type of floor to be Elbow tube is for cleaning under the sofa, table and bed easily. ? Connect the elbow tube to the cleaned. flexible hose and, connect the telescopic tube to the elbow tube.
Emptying the dust chamber The dust chamber needs emptying reaches the MAX indicator the dust tank. on when dust ? Turn off the ? Press the button of the ? cleaner and cover unplug it. and pull the dust chamber out. Remove the dust chamber cap and empty the dust chamber. To reinstall the dust chamber, replace the dust chamber cap and push 8 vacuum the dust chamber into the tank mount as far as it will go.
Operation 2 1 Operation ? Adjusting Pull out the power cord to the desired length and put plug into the socket. ? Press On/Off button to start the vacuum 3 ? the Suction power The flexible hose handle has a manual air flow regulator which allows you to reduce the suction level briefly. Park ? To store after vacuuming vacuuming. To ? Press the cable reel button to retract - stop it, press On/Off button again. the power cord after use.
Cleaning The permanent cap. When the filter motor filter is situated under the dust chamber light comes on ? Press the button of ? Open ? ? the Motor Filter/Air cleaner cover the motor filter and pull requires cleaning. the dust chamber out. the dust chamber cap. Remove the motor filter by rotating it counter-clockwise. Clean the motor filter with the brush under cold running water. ? ? Allow the motor filter to the motor filter should be cleaned every 6 months.
Cleaning the Dust Chamber Cleaning the Exhaust Filters 2 1 3 Open the dust chamber cap. Remove two plates from the dust chamber. ? The exhaust filter is ? To clean the exhaust filter, the filter cover on body by rotating the filter cover a the washable reusable HEPA filter. counter-clockwise. ? Pull out the exhaust filter. ? Clean it with Do not ? use remove cold, running the brush Allow exhaust filter to water. this will damage dry completely in a as the filter.
What to do if there is something wrong with your Vacuum Cleaner What to Do if Your Vacuum Cleaner Does Not Work Check that the vacuum cleaner is plugged in correctly and that the electrical socket is working. What to Do When Suction Performance Decreases ? Turn off the ? Check the ? Check that the dust chamber is not full. ? Check that the motor filter ? Check that the exhaust filter is not vacuum cleaner and telecsopic tube, it.
Notes 13
Notes 14
P/No.
