Owner's Manual

Connections
Tips
Depending
on
your
TV
and other
equipment you
wish
to
connect,
there are various
ways you
could connect
the unit.
Please refer to the manuals of
your
TV,
Stereo
System
or other devices as
necessary
to make the
best connections.
For better sound
reproduction,
connect this unit's
AUDIO OUT
jacks
to the audio
in
jacks
of
your
amplifier,
receiver,
stereo or audio/video
equipment.
See
"Connecting
to
optional equipment"
on
page
10.
Caution
--
Make sure this unit is connected
directly
to the
TV.
Set the
TV
to the correct video
input
channel.
--
Do not connect this unit's AUDIO OUT
jack
to the
phono
in
jack (record deck)
of
your
audio
system.
Connecting
to a
TV
Make one of the
following
connections,
depending
on
the
capabilities
of
your
existing
equipment.
When
using
the COMPONENT/PROGRESSIVE
SCAN VIDEO OUT
jacks,
set TV's
input
to COMPO-
NENT
VIDEO.
When
using
the S-VIDEO OUT
jack,
set the TV's
input
to S-VIDEO.
Basic connection
(AV)
1
Connect the VIDEO
jack
on this unit's DVD/VCR
OUT to the video
in
jack
on the
TV
using
the video
cable.
2
Connect the Left and
Right
AUDIO
jacks
of this
unit's DVD/VCR OUT to the audio
left/right
in
jacks
on the
TV
using
the audio cables.
Basic connection
(RF)
1
Connect the antenna cable from
your
indoor/ out-
door antenna to
AERIAL
jack
on the rear
panel
of
this unit.
2
Connect the
supplied
RF
antenna cable from the
RF.OUT
jack
on the rear
panel
of this unit to
your
television's Antenna
Input.
DVD
exclusive out connection
Component
Video
(Color
Stream
)
connection
1
Connect the COMPONENT/PROGRESSIVE SCAN
VIDEO OUT
jacks
on the unit to the
corresponding
in
jacks
on the
TV
using
an
Y
Pb
Pr
cable.
2
Connect the Left and
Right
AUDIO OUT
jacks
of
the unit to the audio
left/right
in
jacks
on the
TV
using
the audio cables.
S-Video connection
1
Connect the S-VIDEO OUT
jack
on this unit to the
S-Video
in
jack
on the
TV
using
the S-Video cable.
2
Connect the Left and
Right
AUDIO OUT
jacks
of
this unit to the audio
left/right
in
jacks
on the
TV
using
the audio cables.
Progressive
Scan
(ColorStream Pro)
connection
If
your
television is a
high-definition
or
"digital ready"
television,
you may
take
advantage
of the
DVD
Player's progressive
scan
output
for the
highest
video resolution
possible.
If
your
TV
does not
accept
the
Progressive
Scan for-
mat,
the
picture
will
appear
scrambled
if
you try
Progressive
Scan on the
DVD
Player.
1
Connect the COMPONENT/PROGRESSIVE SCAN
VIDEO OUT
jacks
on the unit to the
corresponding
in
jacks
on the
TV
using
an
Y
Pb
Pr
cable.
2
Connect the Left and
Right
AUDIO OUT
jacks
of
the unit to the audio
left/right
in
jacks
on the
TV
using
the audio cables.
Notes
-
Set the
Progressive
to "On" on the
setup
menu for
progressive signal,
see
page
17.
-
Once the
setting
for
progressive
scan
output
is
entered,
an
image
will
only
be visible on a
progressive
scan
compatible
TV
or monitor.
If
you
set
Progressive
Scan to On
in
error,
you
must reset the unit.
1)
Remove
any
disc from the unit and close the disc
tray.
See that "NO DISC" is
displayed
on the dis-
play
window.
2)
Press STOP and hold
it
for five seconds before
releasing
it.
The video
output
will
be restored to
the standard
setting
and a
picture
will
once
again
be visible on a conventional
analog
TV
or monitor.
-
Progressive
scan does not work
with
the
analog
video connections
(yellow
VIDEO OUT
jack)
or S-
VIDEO connection.
Note
If
the
TV
has an S-Video
input,
connect this unit
with
the S-video cable. When
using
an S-video
cable,
do not
connect the
yellow
video cable.
PREPARATION
9
Y
Pb
Pr
L
R
L
R
Y
Pb
Pr
L
R
L
R
VIDEO
INPUT
S-VIDEO INPUT
AUDIO INPUT AERIAL
Rear of TV
Rear of this unit
(DVD
exclusive out
connection)
Rear of this unit
(Basic connection)
COMPONENT VIDEO INPUT
/PROGRESSIVE SCAN
Pr Pb Y
L R