User's Guide E _V_akesureto read the [mpo_ant Precautions beforeusingthe product.Keep the User'sGuide(CD)in an accessibleplacefor future reference. See the label attachedon the product and give the informationto your dealer whenyou ask for seMce.
This unit has been engineered and manufactured to ensure your personal safety_ however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servidng.
On Installation Do not allow anything to rest upon or roll over the power cord, and do not place the display where the power cord is subject to damage, Do not use this display near water such as near a bathtub, washbowl, sink, laundry tub, in a wet basement, or near a swimming pool, kitchen Displays are provided with ventilation openings in the cabinet to allow the release of heat generated during operation, If these openings are blocked, built-up heat can cause failures which may result in a fire hazard,
On Cleaning [] Unplug the display before cleaning the face of the display screen, [] Use a slightly damp (not wet) cloth, Do not use an aerosol directly on the display screen because over-spraying may cause electrical shock, [] When cleaning the product, unplug the power cord and scrub gently with a soft cloth to prevent scratching, Do not clean with a wet cloth or spray water or other liquids directly onto the product, An electric shock may occur, (Do not use chemicals such as benzene, paint thinners or al
!!! Thankfor seleding LG£ produds !!! [] Please make sure the following items are included with your monitor, if any items are missing, User's Guide/Cards DVI-D Signal Cable (Thisfeature is not available in all countries._ contact your dealer. Power Cord (Dependingon the country) 15-pin D-Sub Signal Cable (Toset it up,this signal cable may be attachedto this product before shi 3ping out.,.
[] Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices are turned off. Connectingand Disassemblingthe stand 1, Place the monitor face down on the soft cloth. 2, Assemble the Stand Base into the Stand Body in the correct direction. Stand Stand Base 3, Turn the Stand Base Lock through 90° to fix the Stand Base to the Stand Body. Ba_ Lock 4, Once assembled, lift the monitor up carefully.
5, Turn the Stand Base Lock through 90 ° to separate the Stand Base from the Stand Body. If you can't release the Stand Base even the Locking Knob is at a release position, Please push the indicated knob down and retry it. LockingKnob 6, Pull out the Stand Base to remove.
[] Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display -After installation, adjust the angle as shown below. 1, Adjust the position of the panel in various ways for maximum comfort.
Connecting with the PC 1, Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. 2, Connect signal input cable @ and power cord O in order, then tighten the screw of the signal cable.
Connecting with the PC 1, Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. 2, Connect signal input cable @ and power cord @ in order, then tighten the screw of the signal cable.
Front Pane_Controls W1943TB/W2043TE/W2243T W1943SB/W2043SE/W2243S FUN Button Use this button to enter 4:3 IN WIDE, PHOTO EFFECT menus. For more information,refer to page 14. MENU Button Use this button to enter or exit the On Screen Display. OSD LOCKED/UNLOCKED This function allows you to lock the current control settings, so that they cannot be inadvertentlychanged. Press and hold the MENU button for several seconds. The message "OSD LOCKED" should appear.
• & Buttons JCENGINE Use this function to select optimal image conditions in accordance with the surrounding environment (Brightness, Image type). For more information, refer to page 15. (SOURCE Hot key) When two input signals are connected, you can select the input signal (D-SUB/DVl) you want. When only one signal is connected, it is automatically detected. The default setting is D-Sub. (Only W1943TBAN2043TF_JW2243T) UTO/SET Button Use this button to enter a selection in the On Screen Display.
Screen Adjus men Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make using the OSD. To make adjustments in the On Screen Display, follow these steps: Press the MENU Button, then the main menu of the OSD appears.
The following table indicates all the On Screen Display control, adjustment, and setting menus, • : Analog inputonly NORMAL GAUSSIAN BLUR SEPIA MONOCHROME MOVIE INTERNET USER NORMAL DEMO B qIGHTNESS CONTRAST GAMMA _iiii PRESET (sRGB/6500K/9300K) RED GREEN BLUE HORIZONTAL *VERTICAL *CLOCK *PHASE SHARPNESS LANGUAGE * WHITE BALANCE POWER INDICATOR O
The following OSD screen will appear when you press the FUN the front of the monitor. button on [] MENU Exit [] • • : Move [] SET :Select 4:3 IN WIDE To select the image size of the screen. • WIDE _ "Switch to full screen mode according to input image signal. Change the input image signal ratio to 4:3. • 4:3 _: PHOTO EFFECT To select the color effects of the screen. • NORMAL The PhotoEffect function is disabled. • GAUSSIAN Use the AUTO/SET button to go to sub-menu.
_,_The following OSD screen will appear when you press the ..f.ENGINEbutton on the front of the monitor.This feature lets you easily select the best desired image condition optimized to the environment (ambient illumination, image types etc). = MENU : Save & Exit Sub-menu [] •, Activestate • : Move Inactivestate When the F-ENGINE is executed, the screen is split to show the effects of the selected function. The active state is to the left and the inactive state is to the right side of the screen.
You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Press the MENU Button, then the main menu of the OSD appears.
PICTURE [] MENU [] • [] • [] SET BRIGHTNESS To adjust the brightness of the screen. CONTRAST To adjust the contrast of the screen. GAMMA Set your own gamma value. : -50 / 0 / 50 On the monitor, high gamma values display whitish images and low gamma values display blackish images. : Exit : Decrease :Increase : Select another sub-menu COLOR PRESET [] RED [] MENU : Exit [] • " Decrease [] • Select the screen color. • sRGB: Set the screen color to fit the sRGB standard color specification.
TRACKING [] MENU [] • [] • [] SET HORIZONTAL To move image left and right. VERTICAL To move image up and down. CLOCK To minimize any vertical bars or stripes visible on the screen background. The horizontal screen size will also change. PHASE To adjust the focus of the display. This item allows you to remove any horizontal noise and clear or sharpen the image of characters. Exit Decrease SHARPNESS increase Select another sub-menu O To adjust the clearness of the screen.
SETUP W1943SB/W2043SE!W2243S LANGUAGE To choose the language in which the control names are displayed. OSD POSITION To adjust position of the OSD window on the screen. WHITE BALANCE If the output of the video card is different the required specifications, the color level may deteriorate due to video signal distortion. Using this function, the signal level is adjusted to fit into the standard output level of the video card in order to provide the optimal image.
Check the following before calling for service. @is the power cord of the display connected? • Checkand see ifthe powercord isconnected properlyto the poweroutlet. @is the power indicator light on? Press the Powerbutton. @is the power on and the power indicator red? Adjust the brightnessand the contrast. @is the power indicator blinking? • If the display is in powersaving mode, try moving the mouse or pressingany key on the keyboardto bring up the screen. Try to turn on the PC.
@Display Position is incorrect. +Pressthe AUTO/SETbutton to automatically adjustyour display imageto the idealsetting. tf the resultsare unsatisfactory,adjustthe image positionusingthe H position and V position icon in the on screen display. @On the screen +Pressthe AUTO/SET button to automatically adjustyour display imageto the idealsetting. tf the resultsare unsatisfactory,decreasethe vertical barsor stripesusingthe CLOCK icon in the on screen display. background, vertical bars or stripes are visible.
@The screen color is mono or abnorrnal. @The screen blinks. @Haveyou installedthe display driver? • Checkif the signal cableis properlyconnected and usea screwdriverto fastenif necessary. Make surethe video card is properlyinsertedin the slot. Setthe colorsetting higherthan 24 bits (truecolor) at Control Panel- Settings. Checkif the screen is set to interlacemode and if yes, change itto the recommendresolution.
18.51 inches (47.01 cm} Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size : 47.01 cm 0.30 x 0.30 mm (Pixel pitch) Horizontal Freq. Vertical Freq. Input Form 30 - 61 kHz (Automatic) 56 -75 Hz (Automatic) Separate Sync. SOG (Sync On Green), Digital Signal Input 15 pin D-Sub Connector DVI-D Connector (Digital) RGB Analog (0.7 Vp-p/75 ohm), Digital Input Form VESA 1360 x 768 @60 Hz VESA 1360 x 768 @60 Hz Max Recommena DDC2B On Mode Sleep Mode Off Mode : _< _< 21W(Typ.
18.51 inches (47.01 cm) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size : 47.01 cm 0.30 x 0.30 mrn [Pixel pitch) Horizontal Freq. Vertical Freq. Input Form 30 - 61 kHz (Automatic) 56 - 75 Hz (Automatic) Separate Sync. SOG (Sync On Green) Signal Input Input Form 15 pin D-Sub Connector Max Recommend VESA 1360 x 768 @60 Hz VESA 1360 x 768 @60 Hz RGB Analog (0.7 Vp-p/75 ohm) DDC 2B On Mode Sleep Mode Off Mode : _< _< 21W(Typ.) 1W 1W With Stand i Width _ Width 44.90cm/17.
20.0 inches/50.8 cm) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size : 50.8 cm 0.2768 x 0.2766 mm (Pixel pitch) Horizontal Freq. Vertical Freq. Input Form 30 - 83 kHz (Automatic) 56 - 75 Hz (Automatic) SeDarate Sync. SOG (Sync On Green), Digital Signal Input 15 pin D-Sub Connector DVI-D Connector (Digital) qGB Analog (0.7 Vp-p/75 ohm), Digital Input Form luBon VESA 1600 x 900 @60 Hz VESA 1600x 900 @60 Hz Max Recommend DDC 2B On Mode Sleep Mode Off Moae • _< _< 25 W(Typ.
20.0 inches (50.8 cm) Flat Panel Active matrix-TFT LCD AntFGlare coating Visible diagonal size : 50.8 cm 0.2766 x 0.2766 mm (Pixel pitch) Horizontal Freq. Vertical Freq. Input Form 30 - 83 kHz (Automatic) 56 - 75 Hz (Automatic) Separate Sync. SOG (Sync On Green} Signal Input 15 pin D-Sub Connector Input Form RGB Analog (0.7 Vp-p/75 ohm) Max VESA 1600 x 900 @60 Hz VESA 1600 x 900 _ 60 Hz Recommend DDC 2B On Mode Sleep Mode Off Mode : _< _< 25 W(Typ.) 0.5 W 0.
21.53 nches (54.686 cm) Flat Panel Active matrix-TFT LCD AntFGlare coating Visible diagonal size : 54.686 cm 0.248 x 0.248 mm (Pixel pitch) Horizontal Freq. Vertical Freq. Input Form 30 - 83 kHz (Automatic) 56 - 75 Hz (Automatic) Separate Sync. SOG (Sync On Green], Digital Signal Input 15 pin D-Sub Connector DVI-D Connector (Digital) RGB Analog (0.7 Vp-p/75 ohm), Digital Input Form VESA 1920 x 1080 @60 Hz VESA 1920 x 1080 @60 Hz Max Recommend DDC2B On Mode Sleep Mode Off Mode : _< _< 40W(Typ.
21.53 inches (54.686 cm) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size : 54.686 cm 0.248 x 0.248 mm (Pixel pitch) Horizontal Freq. Vertical Freq. Input Form 30 - 83 kHz (Automatic) 56 - 75 Hz (Automatic) Separate Sync. SOG (Sync On Green) Signal Input Input Form 15 pin D-Sub Connector RGB Analog (0.7 Vp-pi 75 ohm) Max Recommend VESA 1920 x -080 @60 Hz VESA 1920 x 1080 @60 Hz DDC 2B On Mode Sleep Mode Off Mode : _< _< 40W(Typ.) 1W 1W With Stand i Width _ Width 51.
PresetModes (Resolution) W1943SB/W1943TB 1 2 3 4 5 6 7 8 *9 VGA VGA VESA VESA VESA MAC VESA VESA VESA 720 x 400 640 x 480 640 x 480 800 x 600 800 x 600 832 x 624 1024 x 768 1024x 768 1360x 768 31.468 31.469 37.500 37.879 46.875 49.725 48.363 60,123 47.712 70 60 75 60 75 75 60 75 60 W2043SE/W2043TE 1 2 3 4 5 6 7 8 *9 VGA VGA VESA VESA VESA VESA VESA VESA VESA 720 x 400 640 x 480 640 x 480 800 x 600 800 x 600 1024 x 768 1024 x 768 1152 x 864 1600 x 900 31.468 31.469 37.500 37.879 46.875 48.
W2243S/W2243T 1 2 3 4 5 6 7 8 9 10 11 "12 VGA VGA VGA VESA VESA VESA VESA VESA VESA VESA VESA VESA 720 x 400 640 x 480 640 x 480 800 x 600 800 x 600 1024 x 768 1024 x 768 1152 x 864 1280 x 1024 1280 x 1024 1680 x 1050 1920 x 1080 31.468 31.469 37.500 37.879 46.875 48.363 60,123 67.500 63.981 79.976 65,290 67.
This monitor satisfies the specifications or the interchange device. of the Wall mount plate 1, Place the monitor face down on the soft cloth. 2, Turn the Stand Base Lock through 90 ° to separate the Stand Base from the Stand Body. If you can't release the Stand Base even the Locking Knob is at a release position, Please push the indicated knob down and retry it. LockingKnob 3. Pull out the Stand Base to remove.
4, Install the Wall mount plate. Wall mount plate(Separate purchase) This is stand-type or wall mount type and is connectable with Wall mount plate. Please refer to the installation guide for more details, which is provided when Wall mount plate is purchased. LG recommends that wall mounting be performed by a qualified professional installer. Kensington Security Slot Connected to a locking cable that can be purchased separately at most computer stores.
D[gffa[[y yours oooooooo
