WD WD WD WD WD WD 6011 6012 8013 8014 1011 1013 C C C C C C - - - - - - WD WD WD WD WD WD 6011 6012 8011 8012 1012 1014 CH CH CH CH C C
This product has been manufactured at environmental friendly modern facilities.
Dear Customer, We wish that this you the best and keep product, performance. manufactured at modern facilities with total In order to guarantee quality notions, will deliver this, please read this instruction manual thoroughly it for your future reference. www.lge.co.kr CONTENTS Part 1: Part 4: Steps before operating Fullautomatic Washing Machine and safety precautions. Program Part 2: Care and Maintanence. selection and washing operations. Part 5: Technical features.
Part Steps before operating Fullautomatic Washing Machine and safety precautions 1: The current requirement in order for safe operation of this machine is 16 electrician to connect a 16 Amp fuse, if there is not enough current load. Ampheres. You will need to have a certified Your washing machine is set to 220-230 Volts. Do not forget to check the for any damages In order to bring caused grounding in all cases of use with or without the by operations without grounding.
Part 2: Control Top features Technical panel lid Detergent dispenser Front door WD 1012C WD 6011CH WD 6012CH WD 8011CH WD 8012CH WD 1011CH WD 1012CH 85 cm. Width 60 cm. 60 cm. Depth 54 cm. 45 cm. Net 60 kg. 57 kg. weight requirement 4.5 kg. (11.1 lbs) 220-230 V, 10 A. 300 Watts. Heater power 1900 Watts. 50 rpm. Spin speed WD 8011C WD 8012C WD 1011C WD 1012C - - - - - - WD 6011CH WD 6012CH WD 8011CH WD 8012CH WD 1011CH WD 1012CH ) ) ) kg. (10 lbs) 50 Hz.
Part 3: 1. Removing transport safety Determining bolts at the rear location and installation of the machine C C P C C C The transport safety bolts must be removed before any operation of "C", should be turned in the machine. Bolt heads, marked until the bolt can be "C". a anti clockwise direction partially withdrawn. Remove transport safety bolts and rubber bushes by pulling outwards. (A up/down action and a small squirt of washing up liquid should ease removal.
2. Feet adjustment In order for quiet and stable operation, the machine should be placed properly and leveled on is its feet. Your machine unstable, loosen the plastic until the machine is leveled comes with two counternut and perfectly. After adjustable screw or unscrew feet. If the machine the positioning, tighten the foot adjustable counternut for stability. 3.
b) 4. Electrical connection Water drain hose Water drain hose could be placed either at the side of the bath tub, or directly to the drain. The hose should not be bent. Water drain hose should be secured with the elbow so that it would not fall down on the Connect the power cord to the appropirate electrical system which is being supported by the maximum voltage and current rating indicated plate placed inside the kick plate. ground. The hose should be 100 cm.
Control Panel Program selection WD 1011C WD 1012C - - WD 1011CH WD 1012CH Wash selection Temperature Start/ selection Pause Rinse selection Option selection Power Detergent drawer : ( Spin speed selection for : ( WD 6011C WD 6012C Spin speed selection for WD 8011C WD 8012C - - - - WD 6011CH WD 6012CH ) WD 8011CH WD 8012CH ) 7 Spin speed selection
Preparation Loading the machine Place the fabrics no clothing uniformly inside the machine. Hand knits should be at the side of the door. Close the door by pushing lightly. placed inside not be started-a Front door is locked untill the end of the minutes program. safety measure. following the end of the out in the machine.
Program selection Program for white cloths Program for coloured cloths Designed for synthetic fabrics, naylon clothing, curtains and fabrics. Clothing are washed with more water delicately. Shortens iron free wool washing time for lightly soiled fabrics. This function can be synthetic programs for temperatures below 60ºC.
Detergent dispenser Temp. Selection Using this button, you can select final up to 90˚C in whites, temperature up to 60˚C in coloureds, synthetics, wash, Rapid, up to 40˚C in Hand Wool programs. If you don't want to apply heating, you can select also cold wash. Compartment I. detergent compartment prewash cycle. b. Compartment II. detergent compartment for wash cycle. c." Compartment for fabric a.
Rinse Selection Using this button, you can select normal rinse, super rinse, normal rinse + rinse hold, super rinse + rinse hold. If you don't want to apply rinsing, you can select also no rinse, by pressing the rinse button till the leds turn off. Rinse Hold: If you desire to leave your synthetic and wool fabrics in the machine after the wash program you may select the Rinse hold to either press the Rinse button you discharge the water. can Super: prevent them getting wrinkled.
Program selection table OPTIONS PROGRAMMES * Options ** You TEMP. (˚C) RINSE PREWASH HALF RINSE LOAD PLUS ** ECO DRAIN WD 6012C WD 8012C WD 1012C WD 6012CH WD 8012CH WD 1012CH LOAD LOAD kg. kg. FABRIC TYPE soiled cottons and linens 40-90 * * * * * * 5 4.5 Heavy Cold-60 * * * * * * 5 4.5 Normally soiled cottons and linens Cold-60 * * * * * * 2.5 2.5 Normally soiled Cold-40 * * * * 1.5 1.5 Lightly soiled synthetics Cold-40 * * * * 5 4.
Machine operation Place your clothes into the machine and close the front door. Determine the program after referring to the program selection table. Put powder detergent and the fabric softener to the compartments and close the detergent dispenser. Push the POWER button to turn on the washing machine. Program and option leds are turn on.
Child-Care Lock in order to During washing, pressed buttons, lock, press the washing there is a prevent child-care any lock, Temp. and Spin buttons interruptions during as a safety at the same process has been started. All the program and amounts of time. The child-care lock will lock all the When the program finishes, with an measure.
Program operation The selected program can be started by pushing the Star t/Pause button. Front door will be locked and the led indicator will go on. To stop the machine during the program press the start/pause button again. If fabric softener is added in the softener compartment, it will be used in the last cycle. If rinse hold is selected, by re-pressing this button, you can continue rinse the program. If no spin is desired, you may leave the rinse hold button pushed.
Part 5: Care and maintanence Detergent dispenser To clean the detergent residues, by pressing on the area marked the dispenser to its place. the detergent dispenser from its place siphon. Wash the dispenser with water and also clean the dispenser housing before inserting remove on Siphon Clean the siphon (coloured piece in the dispenser) every 30-40 washes. Pull out the siphon by holding from its edges.
Hoses To prevent any leakage, have a technician to control the hoses every two years. If the machine is placed at cold ambient temperatures, the water remining inside the pump and hoses should be removed from the filters. Also to prevent freezing, empty the water intake hoses disconnecting from taps. by Water intake filter At the end of the water intake connection module and water inlet hose-tap side, there exists filters. These filters prevent any dirt and objects passing into the machine.
Cleaning the pump filter To prevent objects entering to the pump, your machine comes with a filter system that extends the pump life. It is advisable that you should clean the filter at every 30-40 washes. Before opening of kick plate opening the filter door, disconnect the screws 90° with a help of screw driver power. Turn the or a coin. Place little pan infront of the filter door to prevent a the machine. Remove the filter it counter-clockwise direction.
The following stain removing tips are approximate and can only washing information of the fabric manufacturer. be used at the washable fabrics. Please Ratios consult the Alcoholic Shoe the fabric first with water, then solution and rinse with vinegar-water solution. baverages: Wipe water-glycerine Without harming the fabric, remove the stain and grind it with detergent. If this doesn't help, prepare a water to alcohol solution (2 to 1) and rub the fabric, then wash it with warm water.
Before Part 7: You turned the machine on, but the leds on the panel. Check the grounding on the power cable Check the front door proper closure. or a are Check if the 8 or planced as the international textile Foam coming out of the detergent dispenser. Check whether your detergent is suitable for automatic machines. Next time use less detergent. are Pump does not drain water. Clean the pump filter. Check whether the drain hose is bent or not.
