For U.K. Customer P/No.: 3828ER3026V CUSTOMER SERVICES Tel. : Fax. :0870-872-7337 LGEUK SERVICE WEB-SITE : 0870 - 873 - LGLG(5454) http://uk.lge.
Washing Machine OWNER'S MANUAL WD(M)-12270BD WD(M)-12275BD WD-12271BD WD-12276BD Thank you for buying a LG Fully Automatic Washing machine. Please read your owner's manual carefully, it provides on safe installation, use and maintenance. instructions Retain it for future reference. Record the model and serial numbers of your washing machine.
P roduct Feature Direct Drive ■ System The advanced Brushless DC motor belt and directly drives the drum without pulley. Tilted Drum and Extra ■ Large Door Opening large opening make it possible clothing more easily. Tilted drum and extra and unload to load Water Circulation ■ Spray detergent Clothes are solution and water onto the load soaked more quickly and The detergent suds can be removed shower during rinse cycle. The water water and detergent more efficiently.
W arnings READ ALL INSTRUCTIONS BEFORE USE For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, personal injury, or loss of life. WARNING! ! IMPORTANT SAFETY INSTRUCTIONS WARNING : To reduce the risk of fire, electric shock, the washer, follow basic ? Do not install be ? ? or precautions, including the ignite a ? ? or whole explode.
S pecification Name : Front loading washing : 220 240V~,50Hz Size : Weight Wash capacity : 686mm(W)×767mm(D)×982mm(H) 86kg Refer to the Rating Label Max. Watt : Spin speed consumption : No Water : 89ℓ Permissible water pressure : 0.3-10kgf/㎠ (30-1000kPa) Power supply : The appearance and units - machine 2200W spin/400/800/1000/1200 may be varied without notice to raise the specifications quality.
nstallation I Install or store where it will not be exposed to temperatures below freezing or exposed to the weather. Properly ground washer to conform with all governing codes and ordinances. The base opening must not be obstructed by carpeting when the washing machine carpeted floor.
I nstallation Installation place requirement Level floor : Allowable slope under entire washer is 1˚ Power outlet : Must be within 1.5 meters of either side of location of washer. Do not overload the outlet with more than one appliance. Additional Clearance : For wall, door and floor (10cm modeling is required. /2cm:right & left side) place or store laundry products on top : rear Do not of washer at any times. They damage can the finish or controls.
I nstallation Electrical connection 1. Do not use an extension cord or double adapter. supply cord is damaged, it must be replaced by the manufacturer or its service agents similarly qualified person in order to avoid a hazard. Always unplug the machine and turn off the water supply after use. Connect the machine to an earthed socket in accordance with current wiring regulations. The appliance must be positioned so that the plug is easily accessible. 2. If the 3. 4. 5.
nstallation I Normal Tap without thread & 1. Unscrew the fixing attach the tap. screw to screw 2. Push the rubber with type inlet hose connector up till the packing is 3. in tight contact the tap. Then tighten the 4 screws. Normal Tap without thread & 1. Untighten the upper connector screw. one touch type inlet hose 2.
I This nstallation equipment is not designed for maritime use or for use mobile installations such as caravans, aircraft etc. stopcock if the machine is to be left for any length of time (e.g. holiday), especially if there is no floor drain(gully) in the immediate vicinity. When disposing of the appliance, cut off the mains cable, and destroy the plug Disable the door lock to prevent young children being trapped inside. Packaging material (e.g. Films, Styrofoam) can be dangerous for children.
I nstallation Level adjustment 1. Adjusting the washing machine level properly prevents excessive noise and vibration. Install the corner appliance of the Timber NOTE on a solid and level floor surface, suspended type flooring or excessive vibration and unblance 2. If the floor is uneven, insert pieces Make sure that all four feet In the case platform, stable and are is may contribute to feet as required.
C are before Before the first Select washing washing cycle (COTTON 60°C, clothing. a without This will remove add a half load of allow the unit to wash detergent) residues from the drum that may have been left during manufacturing. Caring before washing 1. Care Labels Look for garment 2. label on your clothes. This will tell you about the fabric content of your and how it should be washed.
A dding detergent Adding detergent and fabric softener 1. The Dispenser Drawer 3. Detergent The ? dosage detergent should be used according to of the detergent manufacture. the instruction If too ? much detergent is recommended amount, occur heavy malfunction) Use powder loading ? Main wash only U load to the than the can washing result (Causing a motor. detergent only for the front washer.
unction F Recommended Energy courses label data based Fabric Program Cotton according on to the program cotton Proper Temp. (Option) Type Color fast garments is the in Cotton. Wool/Silk Hand Wash Quick 30 60˚C (Cold, 40˚C) "Hand Wash" marked delicate and wool laundry. (30˚C,40˚C) Colored Landry which is lightely soiled fast. (Cold, 40˚C) Water with light filling. Temperature : Rating 139 Rating 159 5.0kg 82 4.0kg 64 3.0kg 61 3.0kg 52 5.
H ow to use washer Bio 1. Cotton selected upon power ? ? ? Press the Power( Press the Start/Pause( ) button Initial condition - Wash : Main wash - Rinse : 3 times - Water temperature Program : Cotton 14 on. to start. ) button. ? ? : 60˚C Press the Selecting Power( ) button to start. Select the conditions which you want to use, by pressing each button. For selecting the each conditions, please refer to the page15~page20 ? -Spin:800rpm - 2.
H (1) (2) (3) (4) ow Button Dial : : to use washer Power (5) (6) (7) (8) Program Button : Start/Pause Button : Option Child lock Button : Rinse Button : Button : Spin Temperature (9) Button : Beeper (10) Button : Time Save (11) Button : Time Delay Power Program 1. Power ? Press the Power( on and off. power ? ) (Program) button to turn ? To cancel the Time Delay function, the Power( ) button should be pressed. 9 programs 2.
ow H to use washer Start/Pause Option By pressing the option one option ? button, only function be selected. 1. Start ? This Start/Pause button is used to start wash cycle or pause the wash cycle. 1. Bio 2. Pause ? ? ? If temporary stop of wash cycle is needed, press "Start/Pause" button. If you want to eliminate ? function When in Pause, the power is turned off automatically after 4 minutes. NB.
H ow to use washer Child lock Rinse ? By pressing the Rinse button, the Rinse type can be selected. ? If you choose to lock the buttons on the control assembly to prevent tampering, this function may be selected. ? Child lock Option can be set by pressing and holding the simultaneously. and Rinse button 1.
to ow H use Time washer Spin Delay ? By pressing the Spin button, speed can be the spin chosen. Preparing washing before starting Turn on the water tap. "Time Delay" - - - Load laundry and close the door. detergent and fabric softener Place the in the drawer. 1. Spin selection ? ? How to set "Time - - - Press Delay" ) button. program Power( Program dial to select the program you require.
H ow to use washer Beeper Water Temperature ? By pressing the Temp. High button, the water temperature can be Low ? selected. - Press the Beeper button repeatedly to adjust the volume of the Beeper. (High/Low/Off) Off Cold -30˚C/40˚C/60˚C/95˚C Beeper ? - Water temperature can be selected below according to the program.
ow H to washer use Display 3. Completion of ? When washing cycle is completed, is displayed on the "Multi display". " 1. Special function display When Child lock is selected, the lamp is on. ? " washing " " 4. Time left delay is selected, it shows remaining times to finish the selected When time ? the ? program. During washing cycle, the remaining washing time is displayed. Recommended program ? 2. Self diagnose display - - ? If the washer encounters operation, displayed.
aintenance M Before cleaning the washer interior, unplug the electrical power cord to avoid electrical shock to avoid electrical shock hazards. When of the appliance, cut off the mains cable, and destroy the plug Disable the door prevent young children being trapped inside. disposing lock to The water inlet filter " -" - message will blink error detergent on the control panel when water does not enter the drawer.
aintenance M Dispenser drawer After ? ? a while and fabric softeners leave detergents a deposit in the drawer. It should be cleaned from time to time with If necessary it can be removed a jet of running water. completely from the machine by pressing by pulling it out.
aintenance M The water circulation nozzle ? Clean the water circulation nozzle, if Cleaning clogged. your washer 1. Exterior of your washer can extend its life. The outside of the machine can be cleaned with Proper care household detergent. Immediately wipe off any spills. Wipe Try water and a neutral non abrasive warm not to hit surface with IMPORTANT: Do not with damp cloth. sharp objects. methylated spirits, diluents use or similar products. 2.
T roubleshooting guide washing machine is equipped with automatic safety functions which detect and diagnose faults at an early stage and react appropriately. When the machine does not function properly or does not function at all, check the following points before you contact your service provider. This Possible Cause Symptom Rattling and clanking noise ? Solution Foreign objects such as coins safety pins maybe in drum or or Stop washer and check drum and drain filter.
T roubleshooting guide Possible Cause Symptom Washer does not start ? Electrical power cord may not plugged in or connection be Solution Make plug fits tightly sure in wall outlet. may be loose. ? House fuse blown, circuit Reset circuit breaker breaker Do not increase fuse tripped,or a power outage has occurred. If problem is a replace capacity. or fuse. circuit overload, have it corrected ? Water supply tap is not turned by a qualified electrician. on water supply tap.
T roubleshooting guide Possible Cause Symptom ? ? ? ? Water Water supply is not adequate in area supply taps are not completely open. Water inlet hose(s) are The filter of the inlet kinked. hose(s) are Solution Check another tap in the house. Fully open tap. Straighten hose(s). Check the filter of the inlet hose(s). clogged. ? ? ? ? ? Drain hose is kinked Clean and The drain filter is Clean the drain filter. or clogged. clogged. straighten the Load is too small.
T of Warranty erms of your old Disposal appliance 1. When this crossed-out wheeled bin product it means the product symbol is attached to by the European a is covered Directive 2002/96/EC. 2. All electrical and electronic products should be disposed of municipal waste stream via designated appointed by the government or the local from the separately collection facilities authorities.