For U.K. Customer P/No.: 3828ER3026V CUSTOMER SERVICES Tel. : 0870 - 873 - LGLG(5454) Fax. : 0870 - 872 - 7337 LGEUK SERVICE WEB-SITE : http://uk.lge.
Washing Machine OWNER’S MANUAL WD(M)-12270BD WD(M)-12275BD WD-12271BD WD-12276BD Thank you for buying a LG Fully Automatic Washing machine. Please read your owner's manual carefully, it provides instructions on safe installation, use and maintenance. Retain it for future reference. Record the model and serial numbers of your washing machine.
P roduct Feature 추가선택, 예약, C ■ Direct Drive System The advanced Brushless DC motor directly drives the drum without belt and pulley. ■ Tilted Drum and Extra Large Door Opening Tilted drum and extra large opening make it possible to load and unload clothing more easily. ■ Water Circulation Spray detergent solution and water onto the load over and over. Clothes are soaked more quickly and thoroughly during wash cycle.
W arnings READ ALL INSTRUCTIONS BEFORE USE ! WARNING! For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, personal injury, or loss of life. IMPORTANT SAFETY INSTRUCTIONS WARNING : To reduce the risk of fire, electric shock, or injury to persons when using the washer, follow basic precautions, including the following: • Do not install or store the washer where it will be exposed to the weather.
S pecification Name Power supply Size Weight Wash capacity Max. Watt Spin speed Water consumption Permissible water pressure : Front loading washing machine : 220 - 240V~, 50Hz : 686mm(W)×767mm(D)×982mm(H) : 86kg : Refer to the Rating Label : 2200W : No spin/400/800/1000/1200 : 89ℓ : 0.3-10kgf/㎠ (30-1000kPa) ❋ The appearance and specifications may be varied without notice to raise the units quality.
I nstallation Install or store where it will not be exposed to temperatures below freezing or exposed to the weather. Properly ground washer to conform with all governing codes and ordinances. The base opening must not be obstructed by carpeting when the washing machine is installed on a carpeted floor.
I nstallation Installation place requirement Level floor : Allowable slope under entire washer is 1˚ Power outlet : Must be within 1.5 meters of either side of location of washer. Do not overload the outlet with more than one appliance. Additional Clearance : For wall, door and floor modeling is required. (10cm : rear /2cm:right & left side) Do not place or store laundry products on top of washer at any times. They can damage the finish or controls.
I nstallation Electrical connection 1. Do not use an extension cord or double adapter. 2. If the supply cord is damaged, it must be replaced by the manufacturer or its service agents or similarly qualified person in order to avoid a hazard. 3. Always unplug the machine and turn off the water supply after use. 4. Connect the machine to an earthed socket in accordance with current wiring regulations. 5. The appliance must be positioned so that the plug is easily accessible.
nstallation I Normal Tap without thread & screw type inlet hose 1. Unscrew the fixing screw to attach the tap. 2. Push the connector up till the rubber packing is in tight contact with the tap. Then tighten the 4 screws. 3. Push the water supply hose vertically upwards so that the rubber packing within in the hose can adhere completely to the tap and then tighten it by screwing it to the right. Normal Tap without thread & one touch type inlet hose 1. Untighten the upper connector screw.
I nstallation This equipment is not designed for maritime use or for use mobile installations such as caravans, aircraft etc. Turn off the stopcock if the machine is to be left for any length of time (e.g. holiday), especially if there is no floor drain(gully) in the immediate vicinity. When disposing of the appliance, cut off the mains cable, and destroy the plug Disable the door lock to prevent young children being trapped inside. Packaging material (e.g. Films, Styrofoam) can be dangerous for children.
I nstallation Level adjustment 1. Adjusting the washing machine level properly prevents excessive noise and vibration. Install the appliance on a solid and level floor surface, preferably in a corner of the room. NOTE Timber or suspended type flooring may contribute to excessive vibration and unblance errors. 2. If the floor is uneven, adjust the adjustable feet as required. (do not insert pieces of wood etc.
C are before washing Before the first washing Select a cycle (COTTON 60°C, add a half load of detergent) allow the unit to wash without clothing. This will remove residues from the drum that may have been left during manufacturing. Caring before washing 1. Care Labels Look for a care label on your clothes. This will tell you about the fabric content of your garment and how it should be washed. 2. Sorting To get the best results, Sort clothes into loads that can be washed with the same wash cycle.
A dding detergent Adding detergent and fabric softener 1. The Dispenser Drawer 3. Detergent dosage • The detergent should be used according to the instruction of the detergent manufacture. • If too much detergent is used more than the recommended amount, too many suds can occur and this will decrease the washing result or cause heavy load to the motor. (Causing a malfunction) • Use powder detergent only for the front loading washer. • Main wash only U • Pre Wash + Main Wash U 2.
F unction Recommended courses according to the laundry type ❋ Energy label data based on program cotton 60˚C, tested in accordance with EN60456. Program Fabric Type Proper Temp. (Option) Cotton Color fast garments (shirts, night dresses, pajamas...)and lightly soiled white cotton (underwear...) 60˚C (Cold, 30˚C, 40˚C, 95˚C) Cotton-Eco Laundry type is the same in Cotton.
H ow to use washer Bio 1. Cotton automatically selected upon power on. • Press the Power( ) button to start. • Press the Start/Pause( • Initial condition - Wash : Main wash - Rinse : 3 times - Spin : 800 rpm - Water temperature : 60˚C - Program : Cotton 14 ) button. 2. Manual Selecting • Press the Power( ) button to start. • Select the conditions which you want to use, by pressing each button. For selecting the each conditions, please refer to the page15~page20 • Press the Start/Pause button.
H ow to use washer (1) Button : Power (2) Dial : Program (3) Button : Start/Pause (4) Button : Option (5) Child lock (6) Button : Rinse (7) Button : Spin (8) Button : Temperature Power (9) Button : Beeper (10) Button : Time Save (11) Button : Time Delay Program 1. Power • Press the Power( ) button to turn power on and off. • To cancel the Time Delay function, the Power( ) button should be pressed. 2. Initial Program • When the Power( ) button is pressed, the washer is ready for Cotton program.
H ow to use washer Start/Pause Option • By pressing the option button, only one option function be selected. 1. Start • This Start/Pause button is used to start wash cycle or pause the wash cycle. 2. Pause • If temporary stop of wash cycle is needed, press “Start/Pause” button. • When in Pause, the power is turned off automatically after 4 minutes. • NB. The door will not open before 1 to 2 minutes when Pause is selected, or at the end of the wash cycle. 1.
H ow to use washer Child lock Rinse • By pressing the Rinse button, the Rinse type can be selected. • If you choose to lock the buttons on the control assembly to prevent tampering, this function may be selected. • Child lock can be set by pressing and holding the Option and Rinse button simultaneously. 1. Normal • Cotton-Eco / Cotton / Synthetic performs 3 Rinses • When child lock is set, all buttons are inoperable.
H ow to use washer Time Delay Spin • By pressing the Spin button, the spin speed can be chosen. Preparing washing before starting “Time Delay” - Turn on the water tap. - Load laundry and close the door. - Place the detergent and fabric softener in the drawer. • How to set “Time Delay” - Press Power( ) button. - Turn the Program dial to select the program you require. - Press Time Delay button and set the desired time. - Press the Start/Pause( ) button.
H ow to use washer Beeper Water Temperature • By pressing the Temp. button, the water temperature can be selected. High - Cold Off Low • Press the Beeper button repeatedly to adjust the volume of the Beeper. (High/Low/Off) - 30˚C / 40˚C / 60˚C / 95˚C Beeper • Water temperature can be selected as below according to the program.
H ow to use washer Display 3. Completion of washing 1. Special function display • When washing cycle is completed, “ ” is displayed on the “Multi display”. • When Child lock is selected, the “ ” lamp is on. 4. Time left • When time delay is selected, it shows the remaining times to finish the selected program. 2. Self diagnose display • If the washer encounters a fault during operation, the associated fault will be displayed.
M aintenance ❋ Before cleaning the washer interior, unplug the electrical power cord to avoid electrical shock to avoid electrical shock hazards. ❋ When disposing of the appliance, cut off the mains cable, and destroy the plug Disable the door lock to prevent young children being trapped inside. The water inlet filter -" " error message will blink on the control panel when water does not enter the detergent drawer.
M aintenance Dispenser drawer ❋ After a while detergents and fabric softeners leave a deposit in the drawer. • It should be cleaned from time to time with a jet of running water. • If necessary it can be removed completely from the machine by pressing the catch downward and by pulling it out. • To facilitate cleaning, the upper part of the fabric softener compartment can be removed.
M aintenance The water circulation nozzle • Clean the water circulation nozzle, if clogged. Cleaning your washer 1. Exterior Proper care of your washer can extend its life. The outside of the machine can be cleaned with warm water and a neutral non abrasive household detergent. Immediately wipe off any spills. Wipe with damp cloth. Try not to hit surface with sharp objects. ❋ IMPORTANT: Do not use methylated spirits, diluents or similar products. 2.
T roubleshooting guide ❋ This washing machine is equipped with automatic safety functions which detect and diagnose faults at an early stage and react appropriately. When the machine does not function properly or does not function at all, check the following points before you contact your service provider. Symptom Possible Cause Solution Rattling and clanking noise • Foreign objects such as coins or safety pins maybe in drum or pump. Stop washer and check drum and drain filter.
T roubleshooting guide Symptom Washer does not start Possible Cause • Electrical power cord may not be plugged in or connection may be loose. Make sure plug fits tightly in wall outlet. • House fuse blown, circuit breaker tripped,or a power outage has occurred. Reset circuit breaker or replace fuse. Do not increase fuse capacity. If problem is a circuit overload, have it corrected by a qualified electrician. Turn on water supply tap. • Water supply tap is not turned on.
T roubleshooting guide Symptom Possible Cause Solution • Water supply is not adequate in area • Water supply taps are not completely open. • Water inlet hose(s) are kinked. • The filter of the inlet hose(s) are clogged. Check another tap in the house. Fully open tap. • Drain hose is kinked or clogged. • The drain filter is clogged. Clean and straighten the drain hose. Clean the drain filter. Straighten hose(s). Check the filter of the inlet hose(s).
T erms of Warranty Disposal of your old appliance 1. When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC. 2. All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities. 3.