Specification

WT7000CW
4.5 cu. ft. Top Load Washer with
TurboDrum™ Technology
LG LAUNDRY
HOME APPLIANCES
QUICK INSTALL & CLEARANCES
For full installation directions/clearances please refer to
the corresponding User Manual and Installation Guide.
IMPORTANT
© 2021 LG Electronics USA, Inc. All rights reserved. "LG Life’s Good" is a registered trademark of LG Corp. All other product and brand names are trademarks or registered trademarks of their respective owners. Design, features and specifications are subject to
change without notice. Non-metric weights and measurements are approximate. Some features may require Internet access. Content and services may vary by product and are subject to change without notice. 6/17/21
DIMENSIONS AND CLEARANCES
ELECTRICAL REQUIREMENTS
•
LG recommends the use of LG hoses. Any leaking,
property damage, or damage to the washing machine
caused by an improper installation or by the use of
non-LG hoses is not covered under the terms of the LG
warranty and is the sole responsibility of the customer
and/or an installer.
•
Water supply pressure must be between 20 psi and
120 psi (138~827 kPa). If the water supply pressure
is more than 120 psi, a pressure reducing valve must
be installed.
•
Inspect the threaded tting on each hose and make
sure there is a rubber seal in place in both ends of
each hose.
•
Connect the water supply hoses to the HOT and COLD
water faucets tightly by hand and then tighten another
2/3 turn with pliers.
•
Always run a gallon or two of water through each inlet
hose to ush dirt, scale and other debris out of the
water lines. Doing so will help prevent future problems
with clogged lter screens, and will also allow you to
verify which water line is hot and which is cold.
•
Attach the hot water line to the hot water inlet on the
back of the washer. Attach the cold water line to the
cold water inlet on the back of the washer. Tighten the
ttings securely. Turn ON both faucets all the way and
check for leaks at both ends of the hoses.
•
The drain hose should always be
properly secured. Failure to properly
secure the drain hose can result in
ooding and property damage.
•
The drain must be installed in
accordance with any applicable local
codes and regulations.
•
Make sure that the drain hose is not
stretched, pinched, crushed, or kinked.
•
Normal height of the end of the hose
should be approximately 35”~47”
(0.9~1.2 m) from the oor.
•
Do not install the end of the drain
hose lower than
29 in. (73.7 cm) or higher than 96 in.
(243.8 cm) above the bottom of the
washer or more than 60 in.
(152.4 cm) away from the washer.
•
Never create an airtight seal between
the hose and the drain with tape or
other means. If no air gap is present,
water can be siphoned out of the
tub resulting in poor wash/rinse
performance or clothing damage.
Tie Stra p
39”
(99 cm)
39”
(99 cm)
Tie Stra p
8”(20 cm)
Tie Stra p
Drain Hose
STANDPIPE Option
LAUNDRY TUB Option
•
Do not insert the end of
the drain hose into the
standpipe more than 8
inches (20cm). Doing so
can cause siphoning,
odors, or improper
draining.
•
Do not use this drain
hose with a oor drain.
The end of the drain hose
must be at least 29 inches
above the oor for proper
draining to occur.
•
The washer should be plugged into a 120-VAC, 60-Hz grounded 3-prong outlet.
Plug in the washer. Improper connection of the equipment-grounding conductor
can result in risk of electric shock. Check with a qualied electrician or service
technician if you are in doubt as to whether the appliance is properly grounded.
Do not modify the plug provided with the appliance. If it does not t the outlet,
have a proper outlet installed by a qualied electrician. Failure to follow these
warnings can cause serious injury, re, electrical shock, or death.
•
The power outlet must be within 60 inches (1.5 m) of either side of the washer.
•
The appliance and outlet must be positioned so that the plug is easily accessible.
•
Do not overload the outlet with more than one appliance.
•
The outlet must be grounded in accordance with current wiring codes and
regulations.
•
Time-delay fuse or circuit breaker is recommended.
•
It is the personal responsibility and obligation of the product owner to have a
proper outlet installed by a qualied electrician.
CONNECTING THE WATER LINES
CONNECTING THE DRAIN HOSE
Rubber Seal
Water Hose
(to tap)
Water Hose
(to water inlet
on washer)
Rubber Seal
Water Faucet
Cold water inlet
Hot water inlet
•
To ensure sufcient clearance for water lines and airow, allow minimum clearances
of at least 1 in. (2.5 cm) at the sides and 4 in. (10 cm) behind the unit. Be sure to
allow for wall, door, or oor moldings that may increase the required clearances.
1" 1"
A
B
4"
3-1/2"
4"
D
C
DIMENSIONS/CLEARANCES/WEIGHTS
A Width 27"
B Height 44 1/2"
C Depth 28 3/8"
D Height with lid open 57 1/5"
Carton Dimensions (WxHxD) 29 19/32” x 46 3/8” x 31 3/8”
ENERGY / RATINGS
IMEF 1.57
IWF 6.5
Ratings CSA Listed
Electrical Requirements 120V @ 60Hz.