Installation Guide

ManualsBrandsLG ManualsAppliances5.8 cu. ft. 27 Inch Top Load Washer

9INSTALLATION

ENGLISH

INSTALLATION

Before Installing

WARNING

may result in injury.

exposed to temperatures below freezing or exposed

to outdoor weather conditions. Failure to follow this warning can cause product or part failure, serious

injury, fire, electric shock, or death.

nform with all governing codes and ordinances. Failure to follow this

warning can cause serious injury, fire, electric shock, or death.

k, do not install the appliance in humid spaces. Failure to follow this

warning can cause serious injury, fire, electric shock, or death.

ening on the bottom of the washer with carpeting or

other materials.

. Do not use an adapter or extension cord. Plug

into a grounded 3-prong outlet. Failure to follow this warning can cause serious injury, fire, electric

shock, or death.

lly not grounded and may present a risk of electric shock only during

servicing. Service personnel - Do not contact the following parts while the appliance is energized: pump,

motor, noise filter cover, protective cover and heater (on applicable models).

Installation Overview

Please read the following installation instructions first after purchasing this washer or transporting it to

another location.

Choosing the Proper Location

Unpacking and Removing Shipping Material

Connecting the Water Inlet Hoses

Connecting the Drain Hose

Leveling the Washer

Summary of content (7 pages)

PAGE 1
INSTALLATION 9 INSTALLATION ENGLISH Before Installing WARNING may result in injury. exposed to temperatures below freezing or exposed to outdoor weather conditions. Failure to follow this warning can cause product or part failure, serious injury, fire, electric shock, or death. nform with all governing codes and ordinances. Failure to follow this warning can cause serious injury, fire, electric shock, or death. k, do not install the appliance in humid spaces.
PAGE 2
10 INSTALLATION f Connecting to the Power Supply g Final Installation Check Tools Needed a Pliers b Flat-Blade Screwdriver c Level Choosing the Proper Location Check the following requirements for the install location before installing the washer. the washer for installation. dust, dirt, water and oil so the leveling feet cannot slide easily. Leveling feet that can move or slide on the floor can contribute to excess vibration and noise. make it more rigid.
PAGE 3
INSTALLATION 11 samples from the tub until the washer is in the final location. Dimensions and Clearances D ENGLISH E F G H Unpacking and Removing Shipping Material NOTE foam insert for future use. If the washer needs to be moved, the foam insert will help prevent damage during transportation. Remove all shipping materials from the washer for proper operation and inspect it for shipping damage. CAUTION excessive noise and vibration. 3 Unfasten the power cord. the washer.
PAGE 4
12 INSTALLATION NOTE faucet and the red hose to the hot water faucet. make sure that they are not pinched, crushed or kinked by other objects. must be between 20 psi and 120 psi (138 - 827 kPa). If the water supply pressure is more than 120 psi, a pressure reducing valve must be installed. ld be set to deliver water at 120 - 135°F (48 - 57°C) to allow the washer to properly control wash temperatures. e washer in a location subject to freezing temperatures.
PAGE 5
INSTALLATION 13 hose can result in flooding and property damage. NOTE NOTE led in accordance with any applicable local codes and regulations. hose is not stretched, pinched, crushed, or kinked. se should be located a minimum of 29.5 inches (75 cm) and a maximum of 96 inches (244 cm) above the bottom of the washer. the end of the drain hose no higher than 66 inches (168 cm) above the bottom of the washer.
PAGE 6
14 INSTALLATION How to Level the Washer 1 the top of the lid. Using these surfaces will result in the washer being unlevel. Position the washer in its final location. crush the water and drain hoses. If you have a, you can use it to check that the washer is level. The slope beneath the washer should not exceed 1 inch, and all 4 leveling feet must rest firmly on the floor. 3 Adjust the leveling feet. raise the washer or the other direction to lower it.
PAGE 7
INSTALLATION 15 the power cord. Doing so may cause death, fire, electric shock, or product malfunction. 4 Press the Start/Pause button. lly checks the water inlet hoses and the drain hose. 5 Check the display for results. grounding conductor can result in risk of electric shock. Check with a qualified electrician or service technician if you are in doubt as to whether the appliance is properly grounded. If it does not fit the outlet, have a proper outlet installed by a qualified electrician.